Google
 

Trailing-Edge - PDP-10 Archives - 6.1_emacs_manuals_1er - manuals/makvfu.doc
There are 23 other files named makvfu.doc in the archive. Click here to see a list.


MAKVFU.DOC -- Changes from V4(3) to V5(3)
October 1981






























COPYRIGHT (C) 1976,1979,1982 BY
DIGITAL EQUIPMENT CORPORATION, MAYNARD, MASS.


THIS SOFTWARE IS FURNISHED UNDER A LICENSE AND MAY BE USED AND  COPIED
ONLY  IN  ACCORDANCE  WITH  THE  TERMS  OF  SUCH  LICENSE AND WITH THE
INCLUSION OF THE ABOVE COPYRIGHT NOTICE.  THIS SOFTWARE OR  ANY  OTHER
COPIES  THEREOF MAY NOT BE PROVIDED OR OTHERWISE MADE AVAILABLE TO ANY
OTHER PERSON.  NO TITLE TO AND OWNERSHIP OF  THE  SOFTWARE  IS  HEREBY
TRANSFERRED.

THE INFORMATION IN THIS SOFTWARE IS SUBJECT TO CHANGE  WITHOUT  NOTICE
AND  SHOULD  NOT  BE  CONSTRUED  AS  A COMMITMENT BY DIGITAL EQUIPMENT
CORPORATION.

DIGITAL ASSUMES NO RESPONSIBILITY FOR THE USE OR  RELIABILITY  OF  ITS
SOFTWARE ON EQUIPMENT WHICH IS NOT SUPPLIED BY DIGITAL.
VFU5.DOC                                                        Page 2


MAKVFU.DOC -- Changes from V4(3) to V5(3)
October 1981



1.0  SUMMARY

MAKVFU is a utility program to generate LP05/LP07/LP14  Direct  Access
Vertical Format files.  MAKVFU commands are described in MAKVFU.HLP.

MAKVFU runs on all releases of TOPS-20.



2.0  EXTERNAL CHANGES

The LINES-PER-INCH command  was  added  for  LP07  printers,  and  the
INFORMATION command will report the setting.



3.0  KNOWN BUGS AND DEFICIENCIES

None.



4.0  INSTALLATION INSTRUCTIONS


4.1  Files Needed to Run MAKVFU

MAKVFU consists of two files, MAKVFU.EXE and MAKVFU.HLP.


4.2  Instructions for Installing MAKVFU

Mount the tape labeled  Installation  Tape  on  MTA0:   and  type  the
following commands:

     SKIP MTA0:5 FILES
     R DUMPER
     TAPE MTA0:
     REWIND
     DENSITY 1600-BPI
     SKIP 1
     RESTORE <*>MAKVFU.EXE,<*>MAKVFU.HLP (TO) SYS:*.*.-1
     REWIND
VFU5.DOC                                                        Page 3


4.3  Files Needed to Build MAKVFU

MAKVFU is built from the following files:

     MAKVFU.MAC

In addition the following files must be on SYS:

     MONSYM.UNV
     MACSYM.UNV
     MACREL.REL



4.4  Instructions for Building MAKVFU

Mount the tape labeled  Distribution  Tape  on  MTA0:   and  type  the
following commands:

     R DUMPER
     TAPE MTA0:
     REWIND
     DENSITY 1600-BPI
     SKIP 1
     RESTORE <*>*.*.* (TO) <self>*.*.*
     REWIND
     ^C
     SUBMIT MAKVFU.CTL/TIME/UNIQ:0/REST


4.5  Special Considerations

None.



5.0  INTERNAL CHANGES

Refer to MAKVFU.TCO for changes to MAKVFU.



6.0  SUGGESTIONS

None.
VFU5.DOC                                                        Page 4


7.0  EXAMPLES

The following sequence of commands  to  MAKVFU  will  produce  a  file
equivalent to the standard VFU file NORMAL.VFU which is distributed by
DEC.  It is possible that other sequences of input  will  produce  the
same VFU file.

     LENGTH 66
     PAGE-SIZE 60
     CHANNEL 1 EVERY 60
     CHANNEL 2 EVERY 30
     CHANNEL 3 EVERY 2
     CHANNEL 4 EVERY 3
     CHANNEL 5 ALL
     FORMS-BREAK 5
     CHANNEL 6 EVERY 10
     CHANNEL 7 EVERY 20
     CHANNEL 8 ALL
     CHANNEL 12 BOTTOM



[End of VFU5.DOC]