Trailing-Edge
-
PDP-10 Archives
-
BB-JR93K-BB_1990
-
10,7/mon/cd2ser.mac
There are 7 other files named cd2ser.mac in the archive. Click here to see a list.
TITLE CD2SER - CARD READER SERVICE FOR CD20 CONTROLLER ON 2020 - V024
SUBTTL D. DETROY/DBD 7 MARCH 89
SEARCH F,S,DEVPRM
$RELOC
$HIGH
;THIS SOFTWARE IS FURNISHED UNDER A LICENSE AND MAY BE USED
; OR COPIED ONLY IN ACCORDANCE WITH THE TERMS OF SUCH LICENSE.
;
;COPYRIGHT (c) DIGITAL EQUIPMENT CORPORATION 1978,1979,1980,1982,1984,1986,1988.
;ALL RIGHTS RESERVED.
.CPYRT<1978,1988>
;
XP VCD2SR,024 ;DEFINE GLOBAL VERSION NUMBER FOR LOADER MAP
CD2SER: ENTRY CD2SER
SUBTTL CD20 REGISTER DEFINITIONS
;OFFSETS INTO THE EXTERNAL PAGE REGISTERS
CDST==0 ;STATUS AND CONTROL REGISTER
CDCC==2 ;COLUMN COUNT REGISTER
CDBA==4 ;BUS ADDRESS REGISTER
CDDB==6 ;DATA BUFFER REGISTER
;STATUS REGISTER BIT DEFINITIONS
CS.ERR==100000 ;ERROR
CS.RDK==040000 ;READER CHECK
CS.EOF==020000 ;END OF FILE
CS.OFL==010000 ;OFF LINE
CS.DER==004000 ;DATA ERROR
CS.DLT==002000 ;DATA LATE
CS.NXM==001000 ;NXM
CS.PWR==000400 ;POWER CLEAR
CS.RDY==000200 ;READY
CS.IEN==000100 ;INTERRUPT ENABLE
CS.TOL==000010 ;TRANSITION TO ON-LINE
CS.HCK==000004 ;HOPPER CHECK
CS.DPK==000002 ;DATA PACKING
CS.RED==000001 ;READ
;DATA BUFFER REGISTER BIT DEFINITOONS
CB.RCK==040000 ;READ CHECK
CB.PCK==020000 ;PICK CHECK
CB.SCK==010000 ;STACK CHECK
SUBTTL SYMBOL DEFINITIONS
;COLUMN 1 SPECIAL CARD CODES
COD029==5252 ;12-0-2-4-6-8
COD026==4242 ;12-2-4-8
CODEOF==7400 ;12-11-0-1
NEWEOF==0017 ;6-7-8-9 PUNCH.
;DEVICE DEPENDENT BITS IN LH OF DEVIOS
CRLAST==100 ;SET WHEN PROCESSING LAST CARD BEFORE OFF-LINE
CR026==200 ;SET WHEN 026 TRANSLTN TO BE MADE.
CRTRBL==4000 ;TROUBLE AT INTERRUPT LEVEL
IOSMON==400000 ;SET TO INDICATE MONITOR IO TO MAPIO
;DEVICE DEPENDENT BITS IN RH OF DEVIOS
SPIMBT==1B29 ;IO STATUS BIT FOR SUPER-IMAGE MODE.
;BUFFER SIZES
ASBFSZ==^D18 ;BUFFER SIZE FOR ASCII MODE.
BIBFSZ==^D27 ;BUFFER SIZE FOR BINARY MODE.
IMBFSZ==^D28 ;BUFFER SIZE FOR IMAGE MODE.
SIBFSZ==^D41 ;BUFFER SIZE FOR SUPER-IMAGE MODE.
SUBTTL CD20 SYSERR DATA BLOCK DEFINITIONS
;WORDS ARE IN EACH CARD READER DDB FOR DAEMON ERROR REPORTING.
.HCNAM==0 ;DEVICE NAME
.HCTYP==1 ;CONTROLLER/DEVICE TYPE
HC.CTL==77B5 ;CONTROLLER TYPE BYTE
.CTILL==0 ;ILLEGAL
.CTB10==1 ;BA10
.CTLP1==2 ;LP100
.CTLP2==3 ;LP20
.CTCD2==4 ;CD20
HC.DEV==77B11 ;DEVICE TYPE BYTE
.DEILL==0 ;ILLEGAL
.DELPT==1 ;LPT
.DECDR==2 ;CDR
.DECDP==3 ;CDP
.DEPLT==4 ;PLT
HC.RTY==777777B35 ;RETRY COUNT FIELD
.RTNON==1B17 ;NON-RECOVERABLE FLAG
.HCUID==2 ;PPN OF USER
.HCPGM==3 ;PROGRAM NAME
.HCSBP==4 ;SUB-BLOCK POINTER
; (XWD .HCL23-.HCSBP,,.HCL20)
.HCL20==5 ;UBA STATUS REGISTER
.HCL21==6 ;UBA MAP SLOT
.HCL22==7 ;CDST,,CDCC
.HCL23==10 ;CDBA,,CDDB
.HCSIZ==11 ;SIZE OF BLOCK
SUBTTL AUTOCONFIGURE
;DRIVER CHARARCTERISTICS
; CR2 = CR2CNF
; CDR = DEVICE TYPE (CARD READER)
; 7 = MAXIMUM DEVICES IN SYSTEM
; 0 = KONTROLLER TYPE
; 0 = MAXIMUM DRIVES PER KONTROLLER
; 0 = HIGHEST DRIVE NUMBER ON KONTROLLER
; MDSEC0 = SECTION FOR KDB/UDB
; MDSEC0 = SECTION FOR DDB
DRVCHR (CR2,CDR,7,0,0,0,MDSEC0,MDSEC0,<DR.GCC!DR.NET>)
.ORG DEVLEN
CDRCNT:!BLOCK 1 ;NUMBER OF CARDS READ
CDRDAP:!BLOCK 1 ;PLACE TO BUILD AOBJN POINTER TO CDRDAE
CDRDAE:!BLOCK .HCSIZ ;SYSERR BLOCK
CDRCHK:!BLOCK 1 ;CHECKSUM OF CURRENT INPUT BINARY CARD
CDRVEC:!BLOCK 1 ;ADDRESS OF VECTOR INTERRUPT CODE
CDRBAS:!BLOCK 1 ;CD20 BASE DEVICE ADDRESS
CDRCDB:!BLOCK 1 ;ADDRESS OF CHANNEL DATA BLOCK
CDRBUF:!BLOCK ^D40 ;INTERNAL BUFFER FOR ONE CARD
CDRBFZ==.-CDRBUF ;SIZE OF THE CDR BUFFER
CR2LEN:! ;LENGTH OF CDR DDB
.ORG
CR2DDB: DDBBEG (CDR,CR2LEN)
SETWRD (DEVCHR,<6*HUNGST,,0>) ;DEVCHR
SETWRD (DEVSER,<MCSEC0+CDRDSP>) ;DEVSER
SETWRD (DEVMOD,<DVIN!DVCDR,,14403>) ;DEVMOD
SETWRD (DEVTYP,<<.TYCDR*.TYEST>!.SPCDR,,0>) ;DEVTYP
SETWRD (DEVCPU,<CDRCHN##>) ;DEVCPU
SETWRD (DEVHCW,<3B11>) ;DEVHCW
SETWRD (CDRDAP,<-.HCSIZ,,CDRDAE>) ;CDRDAP
DDBEND
;CONSO SKIP CHAIN CODE (AUTCON WILL FILL IN THE BLANKS)
CR2ICD: PHASE 0
EXP 0 ;(00) OLD PC FLAGS
EXP 0 ;(01) OLD PC
EXP IC.UOU ;(02) NEW PC FLAGS
EXP .+1 ;(03) NEW PC
JSR PIERR## ;(04) SAVE ACS AND SETUP PDL
DMOVE T1,0 ;(05) GET INTERRUPT FLAGS AND PC
DMOVEM T1,-1 ;(06) SAVE IN TRADITIONAL PLACE FOR XJEN CH'N
SKIPA F,.+1 ;(07) SET UP DDB ADDRESS
EXP 0 ;(10) DDB ADDRESS
XJRST .+1 ;(11) CALL INTERRUPT HANDLER
EXP 0 ;(12) INTERRUPT HANDLER ADDRESS
DEPHASE
CR2ICL==.-CR2ICD ;LENGTH OF CONSO SKIP CHAIN CODE
EQUATE (LOCAL,0,<CR2CKT,CR2KDB,CR2KLN,CR2UDB,CR2ULN>)
EQUATE (LOCAL,0,<CR2ULB,CR2ULP>)
CD2DSP: DRVDSP (CR2,CDRCHN##,CR2DDB,CR2LEN,URDDIA##)
;DEFAULT MONGEN'ED DEVICE TABLE
DEFMDT: MDKS10 (7,CDRIVT,CD11BA,0,0,<MD.KON>)
EXP 0
CR2CFG: XMOVEI T1,CR2MDT## ;MONGEN'ED DEVICE TABLE
XMOVEI T2,DEFMDT ;DEFAULT TABLE
MOVNI T3,1 ;NO MASSBUS UNIT OR DRIVE INFORMATION
MOVEI T4,MD.KON ;MATCH ON KONTROLLER DEFINITION
PUSHJ P,AUTMDT## ;SCAN THE TABLES
JRST CPOPJ1## ;NO MATCHES
PUSH P,T1 ;SAVE MDT DATA
MOVEI T1,CDRBAS ;WORD CONTAINING AN I/O INSTRUCTION
PUSHJ P,AUTFND## ;SEE IF THERE'S ALREADY A DDB
JRST CD2CF1 ;JUST MAKE SURE THE NUMBERS ARE OK
PUSHJ P,AUTADN## ;ALLOCATE A DEVICE NUMBER
HRLI T1,'CDR' ;INCLUDE GENERIC NAME
SETZ T2, ;LOCAL DEVICE
PUSHJ P,AUTDDB## ;CREATE A DDB
JRST TPOPJ## ;NO CORE
ADDM F,CDRDAP(F) ;FIX UP DAEMON ERROR POINTER
CD2CF1: LDB T1,[POINT 21,.CPDVC##,35] ;GET UNIBUS ADDRESS
MOVEM T1,CDRBAS(F) ;SAVE IN DDB
MOVSI T1,CP.CD2 ;GET CHANNEL TYPE BITS
PUSHJ P,AUTCHN## ;ALLOCATE CHANNEL DATA BLOCK
JRST CDRCF2 ;NO CORE
MOVE T1,.CPCHA## ;GET CHANNEL DATA BLOCK ADDRESS
MOVEM T1,CDRCDB(F) ;SALT IT AWAY
HLRZ T1,CDRBAS(F) ;GET UNIBUS ADAPTER NUMBER
MOVEI T2,2 ;NUMBER OF MAPPING REGISTERS NEEDED
PUSHJ P,AUTAMR## ;ALLOCATE MAPPING REGISTERS
JRST CDRCF2 ;NO CORE
MOVE T4,CDRCDB(F) ;GET CHANNEL DATA BLOCK ADDRESS BACK
MOVEM T1,CHNIMR(T4) ;STORE THE DATA AWAY
MOVEM T2,CHNMRC(T4)
MOVEM T3,CHNIEA(T4)
SKIPE CDRVEC(F) ;BEEN HERE BEFORE?
JRST CDRCF4 ;THEN DON'T MESS WITH INTERRUPT CODE
MOVE T1,F ;DATA BLOCK ADDRESS
XMOVEI T2,CR2INT ;INTERRUPT SERVICE
PUSHJ P,AUTICD## ;GENERATE INTERRUPT ROUTINES
CDRCF2: SKIPA T2,F ;NO CORE
JRST CDRCF3 ;ONWARD
MOVEI T1,CR2LEN ;GET DDB LENGTH
PUSHJ P,AUTKIL## ;DELETE THE DDB
PUSHJ P,AUTDDN## ;DEALLOCATE DEVICE NUMBER
JRST TPOPJ## ;PHASE STACK AND RETURN
CDRCF3: MOVEM T2,CDRVEC(F) ;SAVE IN CASE ANYONE IS INTERESTED
PUSHJ P,AUTVII## ;COMPUTE VECTOR INSTRUCTION ADDRESS
MOVE T2,CDRVEC(F) ;GET VECTOR ROUTINE ADDRESS
HRLI T2,(XPCW) ;INTERRUPT INSTRUCTION
MOVEM T2,(T1) ;SAVE IN VECTOR TABLE
MOVE T1,DEVNAM(F) ;GET DEVICE NAME
MOVEM T1,CDRDAE+.HCNAM(F) ;SET IT UP
MOVE T1,[XWD .HCL23-.HCSBP,.HCL20] ;GET SUB-BLOCK POINTER
MOVEM T1,CDRDAE+.HCSBP(F) ;SET IT UP
SETZ T3, ;CLEAR T3
MOVEI T2,.CTCD2 ;INDICATE CD20
DPB T2,[POINT 6,CDRDAE+.HCTYP(F),5] ;STORE CONTROLLER TYPE
MOVEI T2,.DECDR ;INDICATE CDR DEVICE
DPB T2,[POINT 6,CDRDAE+.HCTYP(F),11] ;STORE IT
CDRCF4: POP P,T1 ;GET MDT DATA BACK
POPJ P, ;ALL DONE
SUBTTL CDR SERVICE DISPATCH TABLE
;CARD READER SERVICE DISPATCH TABLE
;DISPATCH TABLE
JRST CDRONL ;ON-LINE CHECK
JRST ECOD2## ;SPECIAL ERROR STATUS
JRST GTBFSZ ;GET BUFFER SIZE AS FCTN OF MODE
JRST CR2INI ;INITIALIZATION
JRST CDRHNG ;HUNG DEVICE
CDRDSP: JRST CDRREL ;RELEASE
JRST ILLOUT## ;CLOSE CALLED ONLY ON ILLEGAL OUTPUT
JRST ILLOUT## ;OUTPUT IS ILLEGAL
JRST CDRINP ;INPUT
SUBTTL INITIALIZATION
CR2INI: MOVEI T1,CDRCNT ;OFFSET TO CARDS READ
MOVEM T1,CDROCR## ;SAVE FOR GETTABS
CAIN F,CR2DDB ;PROTOTYPE?
JRST CPOPJ1## ;YES, SKIP RETURN SO INI ROUTINE CALLED AGAIN
MOVE T1,CDRBAS(F) ;GET BASE ADDRESS OF I/O REGISTERS
MOVEI T2,CS.PWR ;POWER CLEAR BIT
WRIO T2,CDST(T1) ;RESET THE THING
MOVSI T3,DVOFLN ;OFF-LINE BIT
ANDCAM T3,DEVCHR(F) ;ASSUME CDR IS ON-LINE
PUSHJ P,CDRONL ;IS IT REALLY?
IORM T3,DEVCHR(F) ;NO--SET OFF-LINE BIT
MOVEI T2,CS.IEN ;INTERRUPT ENABLE BIT
WRIO T2,CDST(T1) ;ALLOW THEM
PJRST CPOPJ1## ;SKIP RETURN TO FORCE CALL FOR EACH CDR
SUBTTL IN/INPUT UUO
CDRINP: MOVSI T1,DVOFLN ;OFF-LINE BIT
TLZN S,CRTRBL ;TROUBLE AT INTERRUPT LEVEL
TDNE T1,DEVCHR(F) ; OR OFF-LINE?
JRST TKUSER ;YES--TELL USER
TLZN S,IOBEG ;FIRST INPUT?
JRST CDRGO ;NO--JUST DO NEXT BUFFER
TLZ S,CR026 ;YES--ASSUME ANSI CARD CODE
MOVSI T2,PCDRAS## ;SET UP FOR ASCII CARDS
TRNN S,10 ;REALLY ASCII?
JRST CDRIN0 ;YES--PROCEED
MOVSI T2,PCDRBI## ;NO--BINARY AND IMAGE BYTE SIZE= 12.
TRNE S,SPIMBT ;IS IT REALLY SUPER-IMAGE MODE?
HRLI T2,(POINT 16,) ;YES--BYTE SIZE IS 16
CDRIN0: MOVEM T2,DEVPTR(F) ;SET BYTE SIZE
;HERE TO START THE CDR GOING
CDRGO: PUSH P,J ;SAVE J
PUSHJ P,NEWBUF## ;INITIALIZE NEW BUFFER
PJRST ADRERR## ;ADDRESS ERROR
POP P,J ;RESTORE J
HRRI T2,CDRBUF-1(F) ;BUFFER ADDRESS-1 TO T2
HRLI T2,-CDRBFZ ;FORM COMPLETE IOWD FOR MAPIO
TLO S,IOSMON ;INDICATE MONITOR IO TO MAPIO
SETZB P1,P4 ;FIRST CALL,NO FRAME COUNT
MOVE P3,CDRCDB(F) ;GET POINTER TO CHANNEL DATA BLOCK
PUSHJ P,MAPIO## ;SET UP UNIBUS ADAPTOR REGISTERS
JRST CDRSTP ;SHOULDN'T HAPPEN
TLZ S,IOSMON ;CLEAR MONITOR IO BIT
TRO S,IOACT ;SET IO ACTIVE
MOVEM S,DEVIOS(F) ;UPDATE DDB
MOVE T1,CDRBAS(F) ;GET BASE ADDRESS OF I/O REGISTERS
MOVNI T2,^D80 ;80 COLUMNS/CARD
WRIO T2,CDCC(T1) ;SET COLUMN COUNT REGISTER
MOVE T2,CHNIEA(P3) ;GET -11 STYLE ADDRESS
WRIO T2,CDBA(T1) ;SET IN BUS ADDRESS REGISTER
LSH T2,-14 ;ISOLATE TWO HIGH ORDER BITS OF ADDRESS
TRZ T2,777717 ; ON PROPER POSITION FOR CDST
IORI T2,CS.IEN+CS.RED ;INCLUDE INTERRUPT ENABLE AND READ BITS
WRIOB T2,CDST(T1) ;READ A CARD!
PJRST SETHNG## ;SET HUNG TIMER & EXIT
;HERE ON OFF-LINE CARD READER
TKUSER: MOVEM S,DEVIOS(F) ;UPDATE DDB
HRRZ T2,DEVBUF(F) ;ADDRESS OF BUFFER HEADER
EXCTUX <HRRZ T1,@T2> ;CURRENT USER BUFFER
PUSHJ P,UADRCK## ;ADDRESS CHECK IT
EXCTUX <SKIPGE @T1> ;ANY DATA THERE?
PJRST RTEVMI## ;YES--RETURN IT TO USER
PUSHJ P,HNGSTP## ;NO--NOTIFY OPERATOR
JRST CDRINP ;TRY AGAIN
SUBTTL RELEASE UUO & HUNG DEVICE
CDRREL: MOVE T1,CDRBAS(F) ;GET BASE ADDRESS OF I/O REGISTERS
PUSHJ P,UBGOOD## ;IS CD20 ALIVE ON THE UNIBUS?
PJRST CDRST2 ;NO--DO SHORT VERSION OF CDRSTP
PJRST CDRSTP ;YES--SHUT DOWN I/O NORMALLY
CDRHNG: TLO S,CRTRBL ;SET TROUBLE BIT
AOS (P) ;SKIP RETURN TO AVOID HUNG MESSAGE
MOVSI T1,DVOFLN ;OFF-LINE BIT
IORM T1,DEVCHR(F) ;MARK CDR OFF-LINE
PJRST CDRREL ;DO RELEASE CODE
SUBTTL GENERAL INTERRUPT ROUTINE
;ENTER HERE ON ALL INTERRUPTS
CR2INT: PUSHJ P,IOSET## ;SETUP ACS R AND S
LDB J,PJOBN## ;SET UP J WITH JOB NUMBER
MOVE T1,CDRBAS(F) ;GET BASE ADDRESS OF I/O REGISTERS
RDIO T2,CDST(T1) ;READ STATUS REGISTER
HRRM T2,DEVSTS(F) ;SAVE IN DEVSTS
RDIO T3,CDDB(T1) ;READ SECONDARY STATUS REGISTER
HRLM T3,DEVSTS(F) ;SAVE IN DEVSTS
TRNE T2,CS.ERR!CS.TOL ;ERROR OR COMING ON-LINE?
PJRST CDRERR ;YES--GO PROCESS
PJRST CONVRT ;NO--PERFORM ANY DATA CONVERSIONS
CDRDON: MOVEI T1,@DEVPTR(F) ;LAST ADDRESS
MOVEI T2,@DEVIAD(F) ;FIRST ADDRESS (-1)
SUBI T1,1(T2) ;COMPUTE NO. OF WORDS STORED
HRRM T1,1(T2) ;STORE IN 1ST WORD OF BUFFER
AOS CDRCNT(F) ;INCREMENT THE CARD COUNTER
PUSHJ P,ADVBFF## ;ANY BUFFERS LEFT?
PJRST CDRSTP ;NO--SHUT DOWN IO
TLNE S,CRLAST ;YES--IS THIS A "LAST CARD" CONDITION?
PJRST CDRSTP ;YES--SHUT DOWN I/O
PUSHJ P,SETIOD## ;NO--ARRANGE FOR JOB TO RUN AGAIN
PJRST CDRGO ;GO READ NEXT CARD
SUBTTL ERROR INTERRUPT ROUTINES -- DISPATCH
CDRERR: TRNE T2,CS.EOF ;EOF CONDITION?
TLO S,IOEND ;YES--SET FLAG
TRNE T2,CS.OFL ;OFF-LINE?
JRST CDRNOL ;YES--GO HANDLE
;HERE IF MUST BE ON-LINE INTERRUPT
MOVE T3,DEVCHR(F) ;GET OLD STATUS
MOVSI T1,DVOFLN ;OFF-LINE BIT
ANDCAM T1,DEVCHR(F) ;MARK ON-LINE
TLNE T3,DVOFLN ;WAS IT OFF-LINE?
PUSHJ P,PSIONL## ;YES--TELL USER CDR IS NOW ON-LINE
POPJ P, ;DISMISS
SUBTTL ERROR INTERRUPT ROUTINES -- HANDLERS
;HERE TO GIVE USER AN ERROR
CDRSYE: PUSHJ P,CDRSYR ;DO SYSERR REPORTING
MOVE U,CDRCDB(F) ;GET CHANNEL DATA BLOCK
MOVEI T1,UNBTMO!UNBBME
BSIO T1,@CHNUBA(U) ;CLEAR POSSIBLE UBA ERRORS
CDRIOE: TRO S,IODERR ;SET DEVICE ERROR
TLO S,CRTRBL ;SET TROUBLE BIT
PJRST DEVERR## ;CAUSE UUOCON TO RETRY ON UUO LEVEL
;HERE WHEN CDR IS OFF-LINE
CDRNOL: MOVSI T1,DVOFLN ;MARK CDR OFF-LINE
IORM T1,DEVCHR(F) ; FOR ON-LINE INTERRUPT
TRNE T2,CS.NXM!CS.DLT!CS.DER ;IS IT BECAUSE OF ANY OF THESE?
JRST CDRSYE ;YES--LET USER AND F/S KNOW
TRNE T3,CB.RCK!CB.PCK!CB.SCK ;NO--IS IT A HARD READER CHECK?
JRST CDRIOE ;YES--LET USER KNOW
TLO S,CRLAST ;NO--NOW PROCESSING LAST CARD READ BEFORE HOPPER
JRST CONVRT ; EMPTY/STACKER FULL OR STOP BUTTON PUSHED
SUBTTL DATA CONVERSION ROUTINES
CONVRT: MOVEI T4,^D80 ;80 COLS./CARD
CAMLE T4,DEVCTR(F) ;BUFFER SMALLER THAN CARD?
MOVE T4,DEVCTR(F) ;YES--USE SMALLER NUMBER
MOVE T3,[POINT 18,CDRBUF(F)] ;BYTE POINTER TO INPUT
TRNN S,7 ;SKIP IF NOT ASCII OR IMAGE
TRNN S,10 ;SKIP IF IMAGE MODE
JRST NOTIMG ;ASCII OR BINARY
;FALL INTO HERE TO PROCESS IMAGE/SUPER-IMAGE MODE CARD
CDRIMG: ILDB U,T3 ;GET A COLUMN
IDPB U,DEVPTR(F) ;PUT INTO USER BUFFER
SOJG T4,CDRIMG ;LOOP THRU CARD
PJRST CDRDON ;FINISH UP
;HERE IF DATA IS IN ASCII OR BINARY MODE
NOTIMG: ILDB U,T3 ;GET COLUMN 1
MOVE T1,U ;SAVE HERE
TRZ U,770000 ;JUST COLUMN DATA
CAIE U,CODEOF+NEWEOF ;IS IT AN EOF CARD?
CAIN U,CODEOF ;OR THIS TYPE?
PJRST EOFCRD ;YES--SET FLAGS
CAIN U,NEWEOF ;IS IT NEW TYPE EOF?
PJRST EOFCRD ;YES--SET FLAGS
TRNE S,14 ;BINARY MODE?
PJRST CDRBIN ;YES--GO PROCESS IT
;HERE TO PROCESS AN ASCII CARD
CAIN U,COD026 ;026 CARD?
PJRST SET026 ;YES--SET MODE
CAIN U,COD029 ;029 CARD?
PJRST SET029 ;YES--SET MODE
SKIPA U,T1 ;RESTORE COLUMN 1 AND SKIP NEXT
ASCLOP: ILDB U,T3 ;GET NEXT COLUMN
TRNE U,100000 ;MULTI-PUNCHED COLUMN?
JRST [MOVEI U,"\" ;YES--GET INVALID CHARACTER
JRST ASCLO1] ; AND STORE THAT
SETZB T1,T2
CAIN U,5000 ;CONVERT "["
MOVEI U,24202 ; TO INTERNAL FORM
CAIN U,3000 ;CONVERT "]"
MOVEI U,22202 ; TO INTERNAL FORM
LDB T2,[POINT 3,U,26] ;GET ZONES PLUS LOW ENCODED BIT
TRNE U,3 ;AN 8 OR 9 PUNCH?
TRC T2,7 ;YES--ENCODE THAT
TRZE U,40000 ;COPY THIS BIT
TRO T2,10 ; TO HERE
TRNE U,1 ;THIS BIT ON
TRO U,10000 ; MEANS THIS BIT SHOULD BE ON
LSH U,-^D12 ;POSITION REMAINING CODE BITS
TLNE S,CR026 ;026 MODE?
TRO T2,20 ;YES--BUMP T2 TO 026 TABLE
LDB U,CRCVPT##(U) ;PICK UP ASCII CHAR FROM TABLE
ASCLO1: IDPB U,DEVPTR(F) ;PUT INTO USER BUFFER
SOJG T4,ASCLOP ;LOOP THRU CARD
MOVEI T1,15 ;INSERT <CR>
IDPB T1,DEVPTR(F)
MOVEI T1,12 ;INSERT <LF>
IDPB T1,DEVPTR(F)
PJRST CDRDON ;FINISH UP
;HERE TO PROCESS A BINARY CARD
CDRBIN: MOVEI T1,-5(U) ;COL1 - IS THERE A 7-9 PUNCH?
TRNE T1,17
TRO S,IOIMPM ;NO. SET ERROR BIT
LSH U,-6 ;COLUMNS 12-3 ARE WORD COUNT
JUMPE U,CDRGO ;FORGET CARD IF WRDCNT=0
HRRM U,@DEVPTR(F) ;PUT IN R.H. OF 1ST DATA WORD OF BUFFER
IMULI U,3 ;COMPUTE BYTE COUNT
CAMGE U,DEVCTR(F) ;MORE THAN THE BUFFER CAN HOLD?
MOVE T4,U ;NO--USE AS REAL COUNT
ILDB U,T3 ;GET COLUMN 2
TRZ U,770000 ;ONLY COLUMN DATA
HRLM U,@DEVPTR(F) ;STORE CHECKSUM IN USER BUFFER
MOVSM U,CDRCHK(F) ; AND SAVE IN DDB
CDRBI2: ILDB U,T3 ;GET NEXT COLUMN
IDPB U,DEVPTR(F) ;PUT INTO USER BUFFER
SOJG T4,CDRBI2 ;LOOP THRU CARD
MOVEI T2,@DEVIAD(F) ;ADDRESS OF BUFFER
PUSHJ P,CKS12## ;COMPUTE THE CHECKSUM
CAME T1,CDRCHK(F) ;DOES IT COMPARE WITH THAT ON CARD?
TRO S,IODTER ;NO--SET DATA ERROR
PJRST CDRDON ;FINISH UP
SUBTTL VARIOUS UTILITY ROUTINES
;SET CARD CODE MODE
SET026: TLOA S,CR026 ;SET 026 MODE
SET029: TLZ S,CR026 ;SET 029 MODE
TLNN S,CRLAST ;WAS THIS LAST CARD?
PJRST CDRGO ;NO--READ ANOTHER CARD
PJRST CDRSTP ;YES--SHUT DOWN I/O
;HERE TO SET EOF
EOFCRD: TLO S,IOEND ;SET END OF FILE
PJRST CDRSTP ;BACK TO USER
;HERE TO GET BUFFER SIZE, CALLED DURING INIT UUO.
GTBFSZ: MOVEI T1,ASBFSZ ;ASSUME ASCII.
TRNN M,10 ;C(UUO) IS USER'S INIT ARG.
JRST GPBFS1 ;ASCII.
MOVEI T1,BIBFSZ ;NOT ASCII. ASSUME BINARY.
TRNE M,4 ;BINARY?
JRST GPBFS1 ;YES.
MOVEI T1,IMBFSZ ;MUST BE IMAGE MODE.
TRNE M,SPIMBT ;SUPER-IMAGE?
MOVEI T1,SIBFSZ ;YES, 80 WORDS OF DATA/BUFFER.
POPJ P, ;RETURN WITH BUFFER SIZE IN TAC.
GPBFS1: TRZ M,SPIMBT ;SUPER-IMAGE ALLOWED ONLY
POPJ P, ;IF INITIALIZED FOR IMAGE MODE.
;HERE TO STOP THE CDR AND START USER
CDRSTP: MOVE T1,CDRBAS(F) ;GET BASE ADDRESS OF I/O REGISTERS
MOVEI T2,CS.PWR ;POWER CLEAR BIT
WRIO T2,CDST(T1) ;RESET THE CDR
MOVEI T2,CS.IEN ;INTERRUPT ENABLE
WRIO T2,CDST(T1) ;SET IT
CDRST2: TLZ S,CRLAST ;CLEAR LAST CARD BIT
PUSHJ P,SETIOD## ;TAKE OUT OF IO WAIT
PUSHJ P,CLRACT## ;CLEAR IOACT
PJRST RTEVMI## ;RETURN ANY EVM
;HERE TO SEE IF THE CDR IS ON-LINE
CDRONL: MOVE T1,CDRBAS(F) ;GET BASE ADDRESS OF I/O REGISTERS
PUSHJ P,UBGOOD## ;IS CD20 ALIVE ON THE UNIBUS?
POPJ P, ;NO--RETURN OFF-LINE
RDIO T2,CDST(T1) ;READ STATUS REGISTER
TRNN T2,CS.OFL ;IS READER OFF-LINE?
AOS (P) ;NO--IT'S ON-LINE, SO SKIP RETURN
POPJ P, ;RETURN ON-LINE OR OFF-LINE
;HERE TO DO DAEMON ERROR REPORTING FOR SYSERR
CDRSYR: MOVE U,CDRCDB(F) ;GET CHAN DATA BLOCK
RDIO T1,@CHNUBA(U) ;READ UBA STATUS REGISTER
MOVEM T1,CDRDAE+.HCL20(F) ;SAVE IT
LSH T2,-4 ;POSITION 2 BIT ADDRESS EXTENSION
MOVE T1,CDRBAS(F) ;GET BASE ADDRESS OF I/O REGISTERS
RDIO T3,CDBA(T1) ;GET ENDING BUS ADDRESS
DPB T2,[POINT 2,T3,19] ; AND PUT IN HIGH ORDER BITS
IDIVI T3,UBAMUL ;COMPUTE MAP REGISTER OFFSET
ADDI T3,UBAEXP ;ADD IN THE BASE ADDRESS
HLL T3,CHNUBA(U) ;PUT IN PROPER UBA NUMBER
RDIO T2,(T3) ;READ OUT MAP SLOT OF LAST WORD XFER'ED
MOVEM T2,CDRDAE+.HCL21(F) ;SAVE IT
RDIO U,CDST(T1) ;GET CDST
RDIO T2,CDCC(T1) ;GET CDCC
HRLI T2,(U) ;PUT IN LH(T2)
MOVEM T2,CDRDAE+.HCL22(F) ;SAVE IT
RDIO U,CDBA(T1) ;GET CDBA
RDIO T2,CDDB(T1) ;GET CDDB
HRLI T2,(U) ;PUT IN LH(T2)
MOVEM T2,CDRDAE+.HCL23(F) ;SAVE IT
SETZ T1, ;CAUSE SEB ALLOCATION TO HAPPEN
XMOVEI T2,ELGTBL ;POINT TO TRANSFER TABLE
PUSHJ P,XFRSEB## ;FILL AND QUEUE UP RECORD
JFCL ;NO CORE
POPJ P, ;RETURN
ELGTBL: SEBTBL (.ERHCC,ELGEND,<EX.QUE!EX.SYE!EX.DEL>)
MOVE DEVNAM(F) ;(R00) DEVICE NAME
MOVE CDRDAE+.HCTYP(F) ;(R01) CONTROLLER TYPE, ETC.
MOVE JBTPPN##(J) ;(R02) PPN
MOVE JBTNAM##(J) ;(R03) PROGRAM NAME
MOVE CDRDAP(F) ;(R04) WORDS IN SUB-BLOCK,,OFFSET
MOVE CDRDAE+.HCL20(F) ;(R05) UBA STATUS REGISTER
MOVE CDRDAE+.HCL21(F) ;(R06) UBA MAP SLOT
MOVE CDRDAE+.HCL22(F) ;(R07) CDST,,CDCC
MOVE CDRDAE+.HCL23(F) ;(R10) CDBA,,CDDB
ELGEND:! ;END OF TABLE
END