Enter your search terms Submit search form
	Web pdp-10.trailing-edge.com

SETSPD.DOC -- Changes from V4(15) to V5(25)
October 1981






























COPYRIGHT (C) 1978,1980,1982 BY
DIGITAL EQUIPMENT CORPORATION, MAYNARD, MASS.


THIS SOFTWARE IS FURNISHED UNDER A LICENSE AND MAY BE USED AND  COPIED
ONLY  IN  ACCORDANCE  WITH  THE  TERMS  OF  SUCH  LICENSE AND WITH THE
INCLUSION OF THE ABOVE COPYRIGHT NOTICE.  THIS SOFTWARE OR  ANY  OTHER
COPIES  THEREOF MAY NOT BE PROVIDED OR OTHERWISE MADE AVAILABLE TO ANY
OTHER PERSON.  NO TITLE TO AND OWNERSHIP OF  THE  SOFTWARE  IS  HEREBY
TRANSFERRED.

THE INFORMATION IN THIS SOFTWARE IS SUBJECT TO CHANGE  WITHOUT  NOTICE
AND  SHOULD  NOT  BE  CONSTRUED  AS  A COMMITMENT BY DIGITAL EQUIPMENT
CORPORATION.

DIGITAL ASSUMES NO RESPONSIBILITY FOR THE USE OR  RELIABILITY  OF  ITS
SOFTWARE ON EQUIPMENT WHICH IS NOT SUPPLIED BY DIGITAL.

STP5.DOC                                                        Page 2


SETSPD.DOC -- Changes from V4(15) to V5(25)
October 1981



1.0  SUMMARY

5-SETSPD  is  a  privileged  system  program   which   processes   the
5-CONFIG.CMD file and, in so doing, sets many initial parameters about
the system such as:  initial line speeds, system  logical  names,  and
magtape logical to physical correspondences.

5-SETSPD version 5(15) runs only on Release 5 of TOPS-20.

5-SETSPD depends on the file PS:<SYSTEM>5-CONFIG.CMD.



2.0  EXTERNAL CHANGES

None.



3.0  KNOWN BUGS AND DEFICIENCIES

None.



4.0  INSTALLATION INSTRUCTIONS


4.1  Files Needed to Run 5-SETSPD

5-SETSPD consists of one file, 5-SETSPD.EXE and it reads  the  command
file PS:<SYSTEM>5-CONFIG.CMD.


4.2  Instructions for Loading and Installing SETSPD

Mount the tape labeled  Installation  Tape  on  MTA0:   and  type  the
following commands:

     SKIP MTA0:5 FILES
     R DUMPER
     TAPE MTA0:
     REWIND
     DENSITY 1600-BPI
     RESTORE <*>5-SETSPD.EXE (TO) SYSTEM:*.*.-1
     REWIND
     ^C

STP5.DOC                                                        Page 3


4.3  Files Needed to Build SETSPD

5-SETSPD is built from the following files:

     SETSPD.MAC
     SERCOD.UNV
     SERCOD.REL

In addition, the following files must be on SYS:

     MACREL.REL
     MACSYM.UNV
     MONSYM.UNV


4.4  Instructions for Building SETSPD

Mount the tape labeled  Distribution  Tape  on  MTA0:   and  type  the
following commands:

     R DUMPER
     TAPE MTA0:
     REWIND
     DENSITY 1600-BPI
     SKIP 1
     RESTORE <*>*.*.* (TO) <self>*.*.*
     REWIND
     ^C
     SUBMIT SETSPD.CTL/TIME/UNIQ:0/REST

The command file PS:<SYSTEM>5-CONFIG.CMD is produced by using EDIT and
typing in the appropriate commands.


4.5  Special Considerations

SETSPD is run automatically by the monitor  when  it  is  started  and
whenever  one  of  the  front  end  PDP11's  is reloaded.  It need not
however be run under timesharing.



5.0  INTERNAL CHANGES

Refer to SETSPD.TCO for detailed information about changes.



6.0  SUGGESTIONS

None.



[End of STP5.DOC]