Trailing-Edge
-
PDP-10 Archives
-
klad_sources
-
klad.sources/dfkebd.txt
There are no other files named dfkebd.txt in the archive.
;DFKEB
IDENTIFICATION
--------------
PRODUCT CODE: AH-7323C-DD
DIAGNOSTIC CODE: DFKEB
PRODUCT NAME: DFKEBC0 KL10 MONITOR UUO AND MODE DIAGNOSTIC
VERSION: 0.3
DATE RELEASED: APRIL 1985
MAINTAINED BY: 36-BIT DIAGNOSTIC ENGINEERING
AUTHOR: JOHN R. KIRCHOFF
COPYRIGHT (C) 1975, 1985
DIGITAL EQUIPMENT CORPORATION, MAYNARD, MASS.
THIS SOFTWARE IS FURNISHED UNDER A LICENSE FOR USE ONLY ON A
SINGLE COMPUTER SYSTEM AND MAY BE COPIED ONLY WITH THE INCLUSION
OF THE ABOVE COPYRIGHT NOTICE. THIS SOFTWARE, OR ANY OTHER
COPIES THEREOF, MAY NOT BE PROVIDED OR OTHERWISE MADE AVAILABLE
TO ANY OTHER PERSON EXCEPT FOR USE ON SUCH SYSTEM AND TO ONE WHO
AGREES TO THESE LICENSE TERMS. TITLE TO AND OWNERSHIP OF THE
SOFTWARE SHALL AT ALL TIMES REMAIN IN DIGITAL EQUIPMENT
CORPORATION.
THE INFORMATION IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT
NOTICE AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY DIGITAL
EQUIPMENT CORPORATION.
DIGITAL EQUIPMENT CORPORATION ASSUMES NO RESPONSIBILITY FOR THE
USE OR RELIABILITY OF ITS SOFTWARE IN EQUIPMENT WHICH IS NOT
SUPPLIED BY DIGITAL EQUIPMENT CORPORATION.
MAINDEC-10-DFKEB.TXT
PAGE 2
TABLE OF CONTENTS
-----------------
1.0 ABSTRACT
2.0 REQUIREMENTS
2.1 EQUIPMENT
2.2 STORAGE
2.3 PRELIMINARY PROGRAMS
3.0 PROGRAM PROCEDURES
3.1 LOADING PROCEDURE
3.2 STARTING PROCEDURE
3.3 OPERATING PROCEDURE
4.0 DATA SWITCH FUNCTIONS
5.0 ERRORS
6.0 ITERATION COUNTER
7.0 CYCLE TIME
8.0 OPERATIONAL VARIATIONS
9.0 MISCELLANEOUS
10.0 LISTING
MAINDEC-10-DFKEB.TXT
PAGE 3
1.0 ABSTRACT
THIS PDP-10 KL10 DIAGNOSTIC TESTS THE MONITOR UUO'S AND
VARIOUS MACHINE MODES. THE DIAGNOSTIC TESTS MUUO'S IN KERNAL,
SUPERVISOR, CONCEALED AND PUBLIC MODES. IT ALSO TESTS THE
MUUO TRAP LOGIC.
2.0 REQUIREMENTS
2.1 EQUIPMENT
A PDP-10 KL10 EQUIPPED WITH A MINIMUM OF 32K OF MEMORY
CONSOLE PROCESSOR
CONSOLE TELETYPE
DECTAPE
LINE PRINTER (OPTIONAL)
2.2 STORAGE
THE PROGRAM RUNS WITHIN 32K OF MEMORY.
2.3 PRELIMINARY PROGRAMS
PREVIOUS PROCESSOR DIAGNOSTICS
3.0 PROGRAM PROCEDURES
3.1 LOADING PROCEDURE
THIS DIAGNOSTIC REQUIRES THAT THE DECSYSTEM10 SUBROUTINE
PROGRAM BE RESIDENT IN THE PDP-10.
LOAD VIA CONSOLE PROCESSOR OR VIA "DIAMON".
MAINDEC-10-DFKEB.TXT
PAGE 4
3.2 STARTING PROCEDURE
A. SELECT OPERATIONAL CONSOLE DATA SWITCH SETTINGS (REFER TO
4.0 DATA SWITCH FUNCTIONS).
B. EXEC MODE
STAND-ALONE STARTING ADDRESS IS 30000.
3.3 OPERATING PROCEDURE
A. TO THROUGHLY TEST ALL HARDWARE, ALL TEST CONTROL DATA
SWITCHES SHOULD BE SET TO 0.
B. WHEN DEBUGGING HARDWARE, SET SWITCHES TO 0. ALLOW THE
TELETYPE TO PRINT THE ERROR MESSAGES. THIS ALLOWS THE
PROGRAM TO RUN A COMPLETE PASS AND THEN THE ERROR MESSAGES
MAY BE CORRELATED TO QUICKLY DIAGNOSE THE FAILURE. IF A
HARDWARE PROBLEM IS SUCH THAT THE ERROR MESSAGES, AFTER THE
FIRST ONE, HAVE NO MEANING (FIRST ERROR CAUSES ALL FOLLOWING
TESTS TO FAIL) SET THE LOOP ON ERROR SWITCH AND RESTART THE
TEST FROM THE BEGINNING. THE FIRST FAILURE WILL THEN CAUSE
THE PROGRAM TO ENTER A LOOP SUITABLE FOR SCOPING.
THE ERROR MESSAGE USED IN CONJUNCTION WITH THE LISTING AND
SCOPING IF NECESSARY SHOULD ALLOW THE FAILING CONPONENT
TO BE ISOLATED AND REPLACED AND/OR REPAIRED.
C. WHEN TAKING MARGINS, SET DATA SWITCHES 'NOPNT' AND 'DING'.
THIS WILL INHIBIT PRINTOUT BUT WILL ALLOW THE TELETYPE
BELL TO BE RUNG WHEN A ERROR OCCURS. IF THE MARGIN OBTAINED
IS UNACCEPTABLE, THE OPERATOR MAY REVERT TO STANDARD SWITCH
SETTINGS FOR DEBUGGING PURPOSES.
D. ERROR INFORMATION MAY BE OBTAINED QUICKLY BY PRINTING
ERRORS ON THE LINE PRINTER.
E. IN THE EVENT OF A PRINT ROUTINE FAILURE THE 'NOPNT' SWITCH
AND THE 'ERSTOP' SWITCH MAY BE SET TO INHIBIT PRINTOUT
BUT HALT THE PROGRAM POINTING TO THE ERROR.
MAINDEC-10-DFKEB.TXT
PAGE 5
4.0 DATA SWITCH FUNCTIONS
SWITCH STATE FUNCTION
------ ----- --------
0 ABORT 0 NORMAL OPERATION
1 ABORT AT END OF PASS
1 RSTART NOT USED
2 TOTALS NOT USED
3 NOPNT 0 NORMAL TYPEOUT
1 INHIBIT ALL PRINT/TYPEOUT
(EXCEPT FORCED)
4 PNTLPT 0 NORMAL OUTPUT TO TTY
1 PRINT ALL DATA ON LPT
(LOGICAL DEVICE, USER MODE)
5 DING 0 NO FUNCTION
1 RING TTY BELL ON ERROR
6 LOOPER 0 PROCEED TO NEXT TEST
1 ENTER SCOPE LOOP ON TEST ERROR
7 ERSTOP 0 NO FUNCTION
1 HALT ON TEST ERROR
8 PALERS 0 PRINT ONLY FIRST ERROR WHEN LOOPING
1 PRINT ALL ERRORS, EVEN IF SAME ERROR
9 RELIAB 0 QUICK VERIFY MODE
1 RELIABILITY MODE
10 TXTINH 0 PRINT FULL ERROR MESSAGES.
1 INHIBIT COMMENT PORTION OF
ERROR MESSAGES.
11 INHPAG NOT USED - PAGING REQUIRED FOR THIS PROGRAM
12 MODDVC NOT USED
13 INHCSH NOT USED - CACHE NOT USED
MAINDEC-10-DFKEB.TXT
PAGE 6
5.0 ERRORS
ERRORS ARE PRINTED ON THE TTY OR LINE PRINTER. THE ERROR
PRINTOUT CONTAINS THE TEST TITLE, THE PC OF THE FAILURE, ERROR
INFORMATION AND APPLICABLE COMMENTS.
THE PC VALUE IS USEFUL IN RELATING THE FAILURE TO THE LISTING.
THE ERROR NUMBER IS PROVIDED SUCH THAT AN ERROR DICTIONARY MAY
BE MADE AT SOME FUTURE DATE.
IF AN AUDIO INDICATION OF A CONTINUING ERROR IS DESIRED
THE 'DING' SWITCH MAY BE SET.
6.0 ITERATION COUNTER
THE ITERATION COUNT OF THE PROGRAM IS PRINTED AFTER THE
FIRST PASS AND THEN EVERY 100 PASSES.
7.0 CYCLE TIME
THE CYCLE TIME OF THE PROGRAM IS IN THE MILLISECOND RANGE AND
IS THEREFORE SUITABLE FOR TAKING MARGINS, VIBRATION TESTS,
ETC.
MAINDEC-10-DFKEB.TXT
PAGE 7
8.0 OPERATIONAL VARIATIONS
A. DIAGNOSTIC MONITOR
THE PROGRAM IS USABLE WITH THE DIAGNOSTIC MONITOR TO PROVIDE
RELIABILITY TESTS, ACCEPTANCE TESTS, AND/OR TO PROVIDE A
QUICK METHOD OF ISOLATION OF A FAULT TO A PARTICULAR AREA
OF THE PROCESSOR. CERTAIN PROCEDURES ARE USED WHEN THE
PROGRAM IS USED IN THIS MANNER. THEY ARE:
1. THE DIAGNOSTIC MONITOR TRANSFERS CONTROL TO THE PROGRAM
AND STARTS IT AT LOCATION 30002.
2. MONCTL - LOCATION 30043 IS USED AS THE DIAGNOSTIC MONITOR
CONTROL WORD.
LH = 0, STAND-ALONE OPERATION
-1, RUNNING UNDER DIAGNOSTIC MONITOR
RH = RIGHT HALF OF CONSOLE SWITCHES IF UNDER
DIAGNOSTIC MONITOR CONTROL.
9.0 MISCELLANEOUS
THE NON-EX-MEMORY AND PARITY STOP SWITCHES SHOULD BE RESET
(0). THESE ERRORS, ILLEGAL UUO'S AND OTHER ERRORS OF THIS
TYPE ARE HANDLED BY PRINTOUT ON THE TELETYPE.
10.0 LISTING
CORPORATION.
THE INFORMATION IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT
NOTICE AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY DIGITAL
EQUIPMENT CORPORATION.
DIGITAL EQUIPMENT CORPORATION ASSUMES NO RESPONSIBILITY FOR THE
USE OR RELIABILITY OF ITS SOFTWARE IN EQUIPMENT WHICH IS NOT
SUPPLIED BY DIGITAL EQUIPMENT CORPORATION.