Trailing-Edge
-
PDP-10 Archives
-
BB-FZ05B-BM
-
subsys/tsvrelnot.txt
There are 2 other files named tsvrelnot.txt in the archive. Click here to see a list.
Ethernet Communications Server
Terminal Server
Release Notes
(TOPS-20)
February 1986
The Terminal Server Release Notes contain update information and
other miscellaneous items not included in the rest of the
Terminal Server documentation set.
SOFTWARE VERSION: Terminal Server V2.1
The information in this document is subject to change without notice
and should not be construed as a commitment by Digital Equipment
Corporation. Digital Equipment Corporation assumes no responsibility
for any errors that may appear in this document.
The software described in this manual is furnished under a license and
may be used or copied only in accordance with the terms of such
license.
No responsibility is assumed for the use or reliability of software on
equipment that is not supplied by Digital or its affiliated companies.
Copyright (c) 1986 by Digital Equipment Corporation.
All Rights Reserved.
The following are trademarks of Digital Equipment Corporation:
DEC PDP UNIBUS
DECmate P/OS VAX
DECnet Professional VAXcluster
MicroVAX Rainbow VMS
MicroVMS RSX VT
And the Digital logo:
___________________________
| | | | | | | | TM
| d | i | g | i | t | a | l |
|___|___|___|___|___|___|___|
Page iii
CONTENTS
1 DIFFERENCES BETWEEN TERMINAL SERVER V2.0 AND V2.1 . 1
2 USING TERMINAL SERVER V2.1 WITH TOPS-20 LAT SERVICE
NODES . . . . . . . . . . . . . . . . . . . . . . . 2
3 RESTRICTIONS ON HOST-INITIATED CONNECTIONS . . . . . 2
4 BACKWARDS COMPATIBILITY OF SERVER SOFTWARE . . . . . 2
5 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . 2
6 DEFAULT PASSWORDS . . . . . . . . . . . . . . . . . 3
7 COMMAND SYNTAX . . . . . . . . . . . . . . . . . . . 3
8 CONNECTING TO TERMINAL SERVER V2.1 SERVICES . . . . 3
9 PORT FLOW CONTROL . . . . . . . . . . . . . . . . . 4
10 SIDE EFFECTS OF USING THE BREAK KEY . . . . . . . . 5
11 USING PARITY WITH TERMINALS AND PERSONAL COMPUTERS . 5
12 PORTS WITH DEDICATED SERVICES . . . . . . . . . . . 5
13 USING THE TEST COMMAND . . . . . . . . . . . . . . . 6
14 VT200 TERMINALS . . . . . . . . . . . . . . . . . . 6
15 FILE TRANSFERS . . . . . . . . . . . . . . . . . . . 6
16 EXITING FROM THE REMOTE CONSOLE PROGRAM (RMTCON.EXE) 7
17 REPORTING PROBLEMS AND ERRORS . . . . . . . . . . . 7
18 DISTRIBUTION OF YOUR TERMINAL SERVER GUIDES . . . . 8
19 HOW TO ORDER ADDITIONAL DOCUMENTATION . . . . . . 11
TERMINAL SERVER V2.1 RELEASE NOTES
1 DIFFERENCES BETWEEN TERMINAL SERVER V2.0 AND V2.1
Ethernet Terminal Server V2.1 is an enhanced replacement for the
current Ethernet Terminal Server V2.0 product. The V2.1 software
provides the functionality of the V2.0 software with added features to
allow the server to:
o Provide optional password protection at connection time for
services offered by the server. Users who wish to connect to
such services may be prompted for a password before their
connection can be completed. The server manager can assign a
unique password to each service.
o Automatically log out from the server those users with no
sessions. This feature can be enabled on a port-by-port
basis and uses a timer interval that can be modified by the
server manager.
o Automatically drop modem signals on a dial-in port with a
dedicated service when the user logs out of from the service.
The port must have the autoconnect feature disabled.
o Provide a single command that a user can invoke to prepare a
LAT session for applications (such as file transfers with
personal computers) that require data transparency.
o Permit non-privileged users to set any subset of the server
groups for their individual ports, rather than just one or
all groups.
In addition, the V2.1 software includes V2.0 bug fixes and a variety
of minor enhancements. For a complete description of the features of
Terminal Server V2.1, refer to the Terminal Server Operations Guide
and User's Pocket Guide.
1
TERMINAL SERVER V2.1 RELEASE NOTES
2 USING TERMINAL SERVER V2.1 WITH TOPS-20 LAT SERVICE NODES
Terminal Server V2.1 has two new features that cannot be used when the
server is communicating with TOPS V6.1 service nodes:
o The server can accept (and optionally queue) host-initiated
connections to provide transparent printer support for LAT
service nodes. Server command are provided to manage the
queuing of host-initiated connections.
o The server can pass physical terminal characteristics (such
as speed and parity), server name, and port name to LAT
service nodes.
Terminal Server V2.1 uses an enhanced version of the LAT protocol
(V5.1) in implementing these features. A LAT service node must also
implement the same version of the protocol in order to take advantage
of these features. TOPS V6.1 supports only the LAT V5.0 protocol.
Therefore, these features are unavailable to TOPS-20 systems.
3 RESTRICTIONS ON HOST-INITIATED CONNECTIONS
This style of connection to the Terminal Server is supported only from
VAX/VMS and MicroVAX/VMS V4.2 (or later) systems which are running the
LATplus/VMS V1.0 software. In addition, this style of connection is
supported only for use in remote printer applications.
LATplus/VMS software is available with Terminal Server V2.1 VMS and
MicroVMS kits and cannot be ordered separately. However, these VMS
systems can connect to printers on Terminal Servers that have been
downline loaded from TOPS-20 load hosts.
4 BACKWARDS COMPATIBILITY OF SERVER SOFTWARE
Terminal Server V2.1 is compatible with other existing products that
implement the LAT protocol. This compatibility will be ensured
dynamically by the server software and will not require any
intervention on the part of the server manager.
5 TROUBLESHOOTING
Chapter 5 of the Terminal Server Operations Guide has been expanded to
include more information on how to recognize and recover from some of
the more common problems and mistakes that occur when managing
Terminal Servers and LAT networks.
2
TERMINAL SERVER V2.1 RELEASE NOTES
One problem that is not documented in the Operations Guide occurs when
the server is running low on available pool or has reached its current
node limit. If the server receives a multicast message from a new
node under the circumstances above, the node will be announced as
"unknown" rather than "reachable". The server will increase the
resource error count in the SHOW SERVER display each time this event
occurs. Refer to Chapter 5 of the Operations Guide concerning ways to
reduce occurrences of server resource errors.
6 DEFAULT PASSWORDS
The default log-in password is ACCESS. This password is requested on
those ports for which a SET PORT PASSWORD ENABLED was issued before
the user logged in.
The default privilege password is SYSTEM. This password allows a
nonprivileged user to gain access to privileged functions.
You should change both of these passwords after successful
installation of the software, and thereafter on a regular basis.
Change the passwords using the following TSC commands:
TSC> DEFINE LOGIN PASSWORD new-password
TSC> DEFINE PRIVILEGED PASSWORD new-password
7 COMMAND SYNTAX
The command syntax for the server and TSC utility has been modified
slighty to accomodate new V2.1 functionality. Some existing V2.0
commands have new parameters, and new commands have been added.
The command syntax for unprivileged and secure users are backwards
compatible so that either the V2.0 or V2.1 syntax is accepted.
Certain privileged commands have been changed, however, such that the
server cannot provide backwards compatibility to the V2.0 syntax.
Please review the new command syntax as specified in the Terminal
Server Operations Guide to note the changes. You may have to change
your TSC command files if they used V2.0 privileged commands such as
SET SERVICE.
8 CONNECTING TO TERMINAL SERVER V2.1 SERVICES
If users of Terminal Server V1.0 or LAT-11 V1.1 terminal servers
attempt to connect to a Terminal Server V2.1 server that offers more
than one service, those users will always be connected to the first
3
TERMINAL SERVER V2.1 RELEASE NOTES
service that is offered, rather than the service they specify in the
CONNECT command.
If a Terminal Server V2.1 server offers more than two services, the
LAT-11 V1.1 and Terminal Server V1.0 servers will not show that node
as reachable in the SHOW NODES display. These problems originate in
the LAT-11 V1.1 and Terminal Server V1.0 software products, and
upgrading to Terminal Server V2.1 software is recommended where
possible.
Using the TSC program, a maximum of 200 services can be permanently
defined in the server image on a load host. If more than 200 services
are defined, the server may display a halt error code during
initialization, following a downline load. Refer to Appendix B of the
Operations Guide for more information on codes displayed by the
server.
9 PORT FLOW CONTROL
There are several situations that arise on a port where flow control
mechanisms (on either the server or the port device) can cause port
I/O to be blocked unintentionally:
o Resumption of a session may block terminal I/O if flow
control has been disabled with a SET SESSION PASSALL or SET
PORT FLOW DISABLED command.
o If a line card has been hotswapped out and back in, terminal
I/O may become blocked. On remote-access ports, it may be
necessary to force the port device to recycle or logout its
side of the connection to unblock the I/O.
o When output is in progress to a terminal and the BREAK key is
used to get back to local mode, some types of terminals (such
as VT125s) may block I/O.
In most cases, entering <CTRL/Q> or entering and exiting SETUP mode on
the terminal will resume I/O. On VT200 series terminals, is may be
necessary to use the "Clear Comm" option in the SETUP directory while
in SETUP mode.
Some types of applications programs issue system service calls to
enable "pass-all" mode when they begin execution. With "pass-all"
enabled, these programs are passed any XON/XOFF characters that are
sent from the terminal. I/O may become blocked if the server has
received an XOFF character from the terminal when this mode is
enabled. To recover, press BREAK, enter <CTRL/Q>, and resume the
session. To avoid the situation, use the server's SET SESSION PASSALL
command prior to running the application program.
4
TERMINAL SERVER V2.1 RELEASE NOTES
The SET SESSION PASSALL command also should be used to disable flow
control for a session when doing operations such as personal computer
file transfers. The host application, however, may override this.
When doing file transfers, be sure to follow the directions in the
Terminal Server User's Pocket Guide to insure that flow control is
handled properly. The directions can be applied to most situations
that require the server to not intercept special characters in the
data stream.
10 SIDE EFFECTS OF USING THE BREAK KEY
The use of the BREAK key on some terminals may cause some characters
typed to be ignored if the characters are typed very quickly after the
BREAK. Subsequent characters are echoed and handled correctly.
The source of the effect is within the terminal itself and is not
related to the Terminal Server software. The terminals known to
exhibit this side effect are the VT101, VT102, and VT220.
11 USING PARITY WITH TERMINALS AND PERSONAL COMPUTERS
Using certain terminals and personal computers with odd parity enabled
may cause an anomaly when using the BREAK key to force the server port
into local mode.
It is possible to get a BELL when you enter the first character after
the BREAK instead of having the typed character echoed. On some
terminals, the BELL may occur on the BREAK itself. Characters typed
after the BELL are processed normally. You might also notice that the
number of parity errors, as shown in the SHOW PORT and SHOW COUNTERS
displays, has increased at the same time.
12 PORTS WITH DEDICATED SERVICES
If a port has been defined to have a dedicated service, the server
simulates a "hardwired" connection to the node which offers the
service. Depending on what other parameters have been set for the
port, the server may require the user of the port to press <RETURN> as
many as four times before receiving a login prompt from the service
node.
5
TERMINAL SERVER V2.1 RELEASE NOTES
The parameters which affect the behavior of a port in this situation
are AUTOBAUD and AUTOCONNECT. Disabling the autobaud feature forces
the server to requires two less keystrokes. Enabling the autoconnect
feature may save two additional keystrokes.
13 USING THE TEST COMMAND
The test pattern that is output to a terminal when the user issues a
TEST command can usually be stopped when the user presses any key on
the keyboard. The local mode prompt is then displayed, and the user
may issue another command.
If the optional PORT keyword is used in the TEST command, however, the
user will be able to stop the test pattern to the terminal only if
<BREAK> or the local switch character is pressed.
14 VT200 TERMINALS
The function keys on the VT200 series of terminals are not supported
in local mode. For example, the HELP key will not display a help
message in local mode.
15 FILE TRANSFERS
ASCII and binary file transfers between an TOPS-20 LAT service node
and a Digital personal computer are supported. The Terminal Server
User's Pocket Guide explains the general procedure for file transfers.
Part of that procedure requires that once you have logged into the
service node using the PC in terminal emulation mode, you should issue
a server command to disable flow control for the session, and then
disable flow control at the service node before starting the transfer.
There are two steps that are necessary to disable flow control for a
TOPS-20 session:
1. Either before or after the session has been established,
enter local mode on the server and issue a SET PORT FLOW
CONTROL DISABLED command. Note that this command cannot be
issued by a server user whose port has been set as "secure"
by the server manager.
6
TERMINAL SERVER V2.1 RELEASE NOTES
2. Resume (or establish) the session to the TOPS-20 service and
issue a SET TERMINAL NO PAUSE command after you have logged
in.
To re-enable flow control after a file transfer over a TOPS-20
session, you must go through two steps again:
1. From the TOPS-20 service node, issue a SET TERMINAL PAUSE
command.
2. Return to local mode on the server and issue a SET PORT FLOW
CONTROL ENABLED command. The user who has a "secure" server
port cannot issue this command.
Refer to the TOPS-20 Commands Reference Manual for more information on
the usage and applications of PAUSE and other terminal parameters.
16 EXITING FROM THE REMOTE CONSOLE PROGRAM (RMTCON.EXE)
Do not issue either an NCP LOAD NODE or an NCP TRIGGER NODE command
within one minute of entering <CTRL/D> to exit from the Remote Console
Program.
Entering either of these commands from the host within the one-minute
period causes the Terminal Server to loop. If the server does loop,
you will need to press the START button on the Communications Server
hardware unit to reload the Terminal Server.
17 REPORTING PROBLEMS AND ERRORS
Use Software Performance Reports (SPRs) to report any problems with
the Terminal Server. SPR forms are included in your software
distribution kit. Additional forms can be obtained from your local
Digital office.
7
TERMINAL SERVER V2.1 RELEASE NOTES
When completing an SPR form, please describe only one problem per
form. An SPR can be used for:
o Software errors
o Documentation errors when the documentation comment form is
not appropriate
o Inquiries
o Suggestions
o Follow up on a previously submitted SPR
Because problems are often difficult to reproduce with different
system configurations, please include as much detail as possible when
reporting a problem. Define as precisely as possible the state of
your system when the problem occurred and indicate the sequence of
events or commands that caused the problem. Attempt to reproduce the
situation - if it can be reproduced - using the minimum number of
commands.
If one of your user programs causes a problem in the Terminal Server,
and you are unable to send the program to Digital, try to reproduce
the problem with a standard utility. If this is not possible, try to
describe the operation of the program around the suspected failure
area. If the problem is difficult to describe or isolate, it is
recommended that you force a crash dump of the server at the time the
problem occurs. Refer to Chapter 5 of the Terminal Server Operations
Guide for instructions on forcing crash dumps.
Crash dumps may be created manually, or the server may automatically
force a crash dump if an internal error has been detected. When
available, please send such crash dump file(s) to Digital on 1600 BPI
magnetic tape with a short description of how the dumps were copied
onto the media.
NOTE
All media sent to Digital with an SPR will be returned
to the sender.
18 DISTRIBUTION OF YOUR TERMINAL SERVER GUIDES
The documentation set for your Terminal Server consists of a number of
separate guides. Some are packaged with the Terminal Server software,
some with the Terminal Server hardware. Here is a summary of the
guides and their intended readers.
8
TERMINAL SERVER V2.1 RELEASE NOTES
These guides are packed with the Terminal Server software:
o Terminal Server Operations Guide
This guide presents the information needed to operate and
manage the Terminal Server. Give this guide to the person
responsible for installing, maintaining and managing your
Terminal Server.
o Terminal Server Software Installation Guide (TOPS-20)
This contains the information necessary to install and
down-line load the server software. It is intended for the
system manager of a load host or for your network manager.
o Terminal Server User's Pocket Guide (1 copy)
This guide presents details on how to use an interactive
terminal connected to a Terminal Server. Each terminal user
should have a User's Pocket Guide except those for whom the
server manager sets up a dedicated service. You may need
more User's Pocket Guides. See the last section in these
Release Notes for information on how to order additional
documentation.
o Terminal Server Identification Card
This card provides space to record information about the
Terminal Server hardware unit and information to identify the
server in DECnet databases. The system manager of the
server's primary load host should keep this card.
o LAT Network Manager's Guide
This is a reference guide that describes the LAT architecture
and the configuration guidelines that apply to LAT terminal
servers and service nodes. Give this guide to your network
manager. This guide has not yet been updated to reflect
changes made to the architecture to support new features such
as connection solicitation.
These guides are packaged with the Ethernet Communications Server
hardware:
o Site Preparation and Planning Guide
This provides the planning information you need prior to
installing the Ethernet Communications Server. This guide is
intended for the hardware installers.
9
TERMINAL SERVER V2.1 RELEASE NOTES
o Operations and Maintenance Guide
This provides checkout information, an operational summary,
and servicing information for the Ethernet Communications
Server. It should remain with the hardware unit.
o Installation Guide
This contains the information required to install the
Ethernet Communications Server hardware unit. The hardware
installers use this guide.
10
TERMINAL SERVER V2.1 RELEASE NOTES
19 HOW TO ORDER ADDITIONAL DOCUMENTATION
DIRECT TELEPHONE ORDERS
In Continental USA In Canada In New Hampshire
or Puerto Rico call 800-267-6146 or Alaska
or Hawaii call 603-884-6660
call 800-258-1710
DIRECT MAIL ORDERS (US and Puerto Rico*)
DIGITAL EQUIPMENT CORPORATION
P.O. Box CS2008
Nashua, New Hampshire 03061
DIRECT MAIL ORDERS (Canada)
DIGITAL EQUIPMENT OF CANADA LTD.
940 Belfast Road
Ottawa, Ontario, Canada K1G 4C2
Attn: P&SG Business Manager
or approved distributor
INTERNATIONAL
DIGITAL EQUIPMENT CORPORATION
Peripherals and Supplies Centers
P&SG Business Manager
c/o Digital's local subsidiary
or approved distributor
* Any prepaid order from Puerto Rico must be placed
with the Local Digital Subsidiary:
809-754-7575
11
TERMINAL SERVER V2.1 RELEASE NOTES
Ethernet Communications Server
Terminal Server
DOCUMENTATION ORDER NUMBERS
Ethernet Communications Server
Terminal Server Operations Guide (AA-BT83C-TK)
Ethernet Communications Server
Terminal Server Software Installation Guide
(TOPS-20) (AA-FA57A-TM)
Ethernet Communications Server
Terminal Server User's Pocket Guide (AV-X021C-TK)
Ethernet Communications Server
Terminal Server Identification Card (AV-EF44A-TE)
Local Area Transport (LAT) Architecture
Network Manager's Guide (AA-DJ18B-TK)
Ethernet Communications Server
Site Preparation and Planning Guide (EK-DECSA-SP)
Ethernet Communications Server
Operations and Maintenance Guide (EK-DECSA-OP)
Ethernet Communications Server
Installation Guide (EK-DECSA-IN)
12