Trailing-Edge
-
PDP-10 Archives
-
BB-M080I-SM
-
monitor-sources/ttphdv.mac
There are 8 other files named ttphdv.mac in the archive. Click here to see a list.
;Edit 3176 to TTPHDV.MAC by TBOYLE on Thu 1-Nov-84, for SPR #20101
; New XON/XOFF handling
;Edit 3172 to TTPHDV.MAC by TBOYLE on Mon 8-Oct-84
; Fix 3165 - do not set TTSVPD for a short block.
;Edit 3165 to TTPHDV.MAC by TBOYLE on Thu 20-Sep-84, for SPR #18368
; handle remote line speeds correctly.
;Edit 3106 to TTPHDV.MAC by LOMARTIRE on Mon 7-May-84
; Make edit 3105 fix all cases of PI level 6 NOSKED/OKSKED
;Edit 3002 to TTPHDV.MAC by LOMARTIRE on Wed 24-Aug-83
; When closing an NVT connection, don't undo TTPRM if the line
;; is a MCB TTY or the CTY; this is TCO 6.1426
;Edit 3000 to TTPHDV.MAC by GRANT on Mon 22-Aug-83
;In TTSETH, allow multiple MTOPR (.MOSNH) calls on the same line to
;handle ^S/^Q properly
;Edit 2909 - Remove Edit 2906 from source (comment out so it can be
;re-installed if we change our mind to include it in auto-patch)
;Edit 2906 - Fix up XOFF/XON to account for front-end XOFF/XON code
;EDIT 2094 - Index needed at SNDXN2+8L to fix XOFF/XON for incoming chars.
; UPD ID= 257, FARK:<5-1-WORKING-SOURCES.MONITOR>TTPHDV.MAC.5, 9-Dec-82 16:11:38 by MOSER
;EDIT 2875 - USE BREAK THROUGH WRITE FOR XON/XOFF
; UPD ID= 75, SNARK:<5.1.MONITOR>TTPHDV.MAC.4, 9-Oct-82 10:27:40 by GRANT
;TCO 5.1.1089 - Rewrite TNTCLS, save link IDs rather than LL block addresses
; UPD ID= 91, FARK:<5-WORKING-SOURCES.MONITOR>TTPHDV.MAC.3, 12-Aug-82 11:28:08 by MOSER
;EDIT 2646 - PASS DYNAMIC DATA TO TTCBF9 IN TINET
; UPD ID= 26, SNARK:<5.1.MONITOR>TTPHDV.MAC.8, 18-Jul-82 13:49:36 by MURPHY
;TCO 5.1.1048 - Add TTCLSH to clear "set host" state when closing LL.
; UPD ID= 23, SNARK:<5.1.MONITOR>TTPHDV.MAC.7, 18-Jul-82 13:30:04 by MURPHY
;TCO 5.1.1047 - Put NOSKED before call to TNTCLS to interlock ULLCZQ.
; UPD ID= 22, SNARK:<5.1.MONITOR>TTPHDV.MAC.6, 18-Jul-82 13:27:33 by MURPHY
;TCO 5.1.1046 - Check TTNUS before call to TNUREC.
; UPD ID= 17, SNARK:<5.1.MONITOR>TTPHDV.MAC.5, 30-Jun-82 09:23:14 by GRANT
;Fix edit history - change TCO 6.1148 to TCO 5.1.1039 and 6.1154 to 5.1.1041
; UPD ID= 15, SNARK:<5.1.MONITOR>TTPHDV.MAC.4, 30-Jun-82 08:52:12 by GRANT
;TCO 5.1.1038 - Remove CALL SQIACK in DECnet NVT processor
; UPD ID= 3, SNARK:<5.1.MONITOR>TTPHDV.MAC.3, 5-Jun-82 20:18:45 by GRANT
;TCO 5.1.1041 - Fix failure return from CALL SNDCHK in MCSTRO.
;Change comment in CHKLLT.
; UPD ID= 2, SNARK:<5.1.MONITOR>TTPHDV.MAC.2, 5-Jun-82 20:17:59 by GRANT
;TCO 5.1.1039 - Remove code which breaks DECnet connection when a character is
;received on a line on which there is no job
; UPD ID= 480, SNARK:<5.MONITOR>TTPHDV.MAC.4, 22-Feb-82 09:00:15 by PLATUKIS
;TCO 5.1734 - fix instruction at MCTYIZ+1 to properly use the FLOHLD constant
;in the same way NSPSRV does.
; UPD ID= 418, SNARK:<5.MONITOR>TTPHDV.MAC.3, 19-Jan-82 12:07:41 by MURPHY
;TCO 5.1688 - report TTYSTP only once per line
; UPD ID= 277, SNARK:<5.MONITOR>P3-TTPHDV.MAC.2, 21-Oct-81 11:41:33 by GRANT
;TCO 5.1594 - Move code from MCTYI2 and MCTYI3 into NSPSRV
; UPD ID= 193, SNARK:<5.MONITOR>TTPHDV.MAC.56, 17-Sep-81 13:19:49 by GRANT
;Reinstate the UPD ID=153 edit. Also, it should say TCO 5.1490 no 5.1409
; UPD ID= 172, SNARK:<5.MONITOR>TTPHDV.MAC.55, 14-Sep-81 13:44:20 by GRANT
;Temporarily undo previous edit
; UPD ID= 153, SNARK:<5.MONITOR>TTPHDV.MAC.54, 8-Sep-81 17:31:11 by GRANT
;Needed for TCO 5.1490 - Remove segment number handling in MCTYI3
; UPD ID= 172, SNARK:<5.MONITOR>TTPHDV.MAC.55, 14-Sep-81 13:44:20 by GRANT
;Temporarily undo previous edit
; UPD ID= 153, SNARK:<5.MONITOR>TTPHDV.MAC.54, 8-Sep-81 17:31:11 by GRANT
;Needed for TCO 5.1409 - Remove segment number handling in MCTYI3
;Minor changes needed for handling LLOMSG queue in MCTYI3 and MCTYI2
; UPD ID= 138, SNARK:<5.MONITOR>TTPHDV.MAC.53, 2-Sep-81 16:38:01 by GRANT
;Eliminate cause of OKSKBG BUGHLT - in TNHCLS, NOSKED before calling TTCOB5
; UPD ID= 2307, SNARK:<5.MONITOR>TTPHDV.MAC.52, 8-Jul-81 11:20:59 by MURPHY
;CALL REQNS INSTEAD OF TNUSND FROM TTCHI
; UPD ID= 2295, SNARK:<5.MONITOR>TTPHDV.MAC.51, 6-Jul-81 13:50:54 by MURPHY
;DEBUG CODE TO RECORD DEAD LINKS
;PROCESS ALL INPUT IN TINET BEFORE QUITTING
; UPD ID= 2269, SNARK:<5.MONITOR>TTPHDV.MAC.50, 29-Jun-81 17:48:31 by MURPHY
;ANTX01
; UPD ID= 2190, SNARK:<5.MONITOR>TTPHDV.MAC.49, 11-Jun-81 15:59:54 by MURPHY
;CHANGE TQNx TO TMNx REFLECTING CHANGE IN MACSYM
;DITTO
; UPD ID= 1867, SNARK:<5.MONITOR>TTPHDV.MAC.45, 21-Apr-81 23:41:55 by MURPHY
;DITTO
; UPD ID= 1865, SNARK:<5.MONITOR>TTPHDV.MAC.44, 21-Apr-81 18:29:43 by MURPHY
;DITTO
; UPD ID= 1830, SNARK:<5.MONITOR>TTPHDV.MAC.43, 17-Apr-81 14:19:33 by MURPHY
;MAKE LINE SHUTOFF FOR 5 SECONDS INSTEAD OF 3
;REVISE SENDALL LOGIC
;REVISE STARTUP LOGIC
; UPD ID= 1752, SNARK:<5.MONITOR>TTPHDV.MAC.42, 20-Mar-81 13:32:21 by MURPHY
;Ditto
; UPD ID= 1745, SNARK:<5.MONITOR>TTPHDV.MAC.41, 19-Mar-81 23:11:04 by MURPHY
;Fix problems with line shut-off and XOFF/XON logic.
; UPD ID= 1663, SNARK:<5.MONITOR>TTPHDV.MAC.40, 11-Mar-81 16:30:30 by MURPHY
;Fix up some failures of DTEQ which were not handled
; UPD ID= 1554, SNARK:<5.MONITOR>TTPHDV.MAC.39, 11-Feb-81 17:33:25 by MURPHY
;MAKE SURE LINE GETS RESTARTED AFTER STOP BECAUSE INBFR OR TTBBUF FULL
; UPD ID= 1550, SNARK:<5.MONITOR>TTPHDV.MAC.38, 10-Feb-81 17:57:41 by MURPHY
;FIX XOFF DURING SYSTEM STARTUP PROBLEM
;CHANGE NAMES TO BLSUB., BLCAL.
;DITTO
; UPD ID= 1477, SNARK:<5.MONITOR>TTPHDV.MAC.35, 22-Jan-81 12:24:13 by MURPHY
;FIX TTQAD PROBLEMS
; UPD ID= 1377, SNARK:<5.MONITOR>TTPHDV.MAC.34, 22-Dec-80 18:25:37 by MURPHY
;<5.MONITOR>TTPHDV.MAC.33, 17-Dec-80 18:10:33, EDIT BY MURPHY
;TNUREC
; UPD ID= 1361, SNARK:<5.MONITOR>TTPHDV.MAC.32, 17-Dec-80 15:46:27 by MURPHY
;CHKLLT
;<5.MONITOR>TTPHDV.MAC.31, 12-Dec-80 11:11:34, EDIT BY MURPHY
;<5.MONITOR>TTPHDV.MAC.30, 12-Dec-80 10:34:51, EDIT BY MURPHY
;<5.MONITOR>TTPHDV.MAC.29, 12-Dec-80 10:23:26, EDIT BY MURPHY
;FLOW CONTROL
;<5.MONITOR>TTPHDV.MAC.28, 9-Dec-80 15:16:03, EDIT BY MURPHY
;CKMCOU
;<5.MONITOR>TTPHDV.MAC.27, 5-Dec-80 16:49:34, EDIT BY MURPHY
;VARIOUS MCB FIXES AND ENHANCEMENTS
;<5.MONITOR>TTPHDV.MAC.25, 24-Nov-80 16:46:49, EDIT BY MURPHY
;Requeue line if SQILS or SQIACK fails
;<5.MONITOR>TTPHDV.MAC.24, 21-Nov-80 18:29:16, EDIT BY MURPHY
;FLUSH LINK IF INPUT AND NO JOB
; UPD ID= 1301, SNARK:<5.MONITOR>TTPHDV.MAC.23, 19-Nov-80 17:05:35 by MURPHY
;LOCAL XON,XOFF OPTION FOR NVTS
; UPD ID= 1290, SNARK:<5.MONITOR>TTPHDV.MAC.22, 18-Nov-80 16:45:45 by MURPHY
;<5.MONITOR>TTPHDV.MAC.21, 31-Oct-80 17:37:34, EDIT BY MURPHY
;<5.MONITOR>TTPHDV.MAC.20, 30-Oct-80 22:59:18, EDIT BY MURPHY
;<5.MONITOR>TTPHDV.MAC.19, 21-Oct-80 12:10:07, EDIT BY MURPHY
;<5.MONITOR>TTPHDV.MAC.18, 20-Oct-80 17:12:52, EDIT BY MURPHY
;<5.MONITOR>TTPHDV.MAC.17, 20-Oct-80 14:40:25, EDIT BY MURPHY
;<5.MONITOR>TTPHDV.MAC.16, 7-Oct-80 15:27:36, EDIT BY MURPHY
;<5.MONITOR>TTPHDV.MAC.15, 6-Oct-80 11:32:21, EDIT BY MURPHY
; UPD ID= 1126, SNARK:<5.MONITOR>TTPHDV.MAC.14, 5-Oct-80 15:02:40 by MURPHY
;DITTO
;<5.MONITOR>TTPHDV.MAC.13, 3-Oct-80 14:04:57, EDIT BY MURPHY
; UPD ID= 1120, SNARK:<5.MONITOR>TTPHDV.MAC.12, 3-Oct-80 12:21:22 by MURPHY
;DITTO
; UPD ID= 1113, SNARK:<5.MONITOR>TTPHDV.MAC.11, 3-Oct-80 01:00:51 by MURPHY
;NVT IMPROVEMENTS
; UPD ID= 1077, SNARK:<5.MONITOR>TTPHDV.MAC.10, 1-Oct-80 10:37:44 by MURPHY
;RELEVANT END STATEMENTS FOR STKVAR, ETC.
; UPD ID= 1063, SNARK:<5.MONITOR>TTPHDV.MAC.9, 30-Sep-80 10:16:58 by MURPHY
;DITTO
; UPD ID= 1057, SNARK:<5.MONITOR>TTPHDV.MAC.8, 26-Sep-80 12:13:03 by MURPHY
;MCB FIXES
; UPD ID= 944, SNARK:<5.MONITOR>TTPHDV.MAC.7, 20-Aug-80 20:09:15 by MURPHY
;MCB FIXES
; UPD ID= 925, SNARK:<5.MONITOR>TTPHDV.MAC.6, 20-Aug-80 10:21:12 by MURPHY
;INCLUDE MCB DEVICE
; UPD ID= 699, SNARK:<5.MONITOR>TTPHDV.MAC.5, 25-Jun-80 17:23:34 by MURPHY
;REMOVE TTDBEF REDUNDANT SUBROUTINE
;MERGE TTFEDV AND TTDZDV FILES INTO TTPHDV
;CHANGE DEVICE VECTORING
; UPD ID= 645, SNARK:<5.MONITOR>TTFEDV.MAC.4, 16-Jun-80 12:09:09 by MURPHY
;CLEAN UP VECTOR COMMENTS
; UPD ID= 443, SNARK:<5.MONITOR>TTFEDV.MAC.3, 15-Apr-80 09:41:02 by KONEN
;TCO 4.1.1143 -- Check for XOFF before storing character in big buff.
; UPD ID= 405, SNARK:<5.MONITOR>TTFEDV.MAC.2, 3-Apr-80 16:06:55 by HALL
;CHANGES TO WRITE-PROTECT THE RESIDENT MONITOR:
; CHANGE ALL REFERENCES TO TT1LIN TO EXPECT A TABLE
;<4.1.MONITOR>TTFEDV.MAC.52, 16-Nov-79 11:29:17, EDIT BY MILLER
;ASGALL NOW SKIPS
;<4.MONITOR>TTFEDV.MAC.51, 1-Nov-79 17:15:09, EDIT BY MILLER
;Previous edit lines deleted
IFN .MCFLG,< ;INCLUDE ONLY UNDER MASTER FLAG
SUBTTL DECNET NETWORK TERMINAL DEPENDENT CODE
SEARCH NSPPAR
;THIS MODULE IS NECESSARY TO SUPPORT THE NETWORK VIRTUAL TERMINALS (NVT)
;OVER DECNET.
;SPECIAL DEFINITIONS
TTMCLN==TTDDLN ;LENGTH FOR MC
DEFSTR TTHLL,TTDEV,35,18 ;LOGICAL LINK FOR THIS LINE (HOST SIDE)
IFN CZQDBG,< ;IF DEBUG CODE
RS CZQPTR,1 ;PTR INTO TRACE BUFFER
LCZQBF==40 ;LENGTH OF TRACE BUFFER
RS CZQBF,LCZQBF ;TRACE BUFFER
>
;INITIATE NET ACTIVITY IF POSSIBLE. CALLED FROM NSPSRV WHEN SIGNIFICANT EVENTS OCCUR.
;ACCEPTS: T1/ LL BLOCK ADDRESS
;RETURNS: +1
CHKLLT::JE LLTTA,(T1),R ;RETURN IMMED IF NO TTY ON THIS LL
SAVEAC <T2,T3,T4>
LOAD T2,LLTTY,(T1) ;SEE IF CONNECTED TO A TTY
SKIPG T2,TTACTL(T2) ;ACTIVE LINE NOW?
RET ;NO, SHOULD ALREADY HAVE CLEANUP IN PROGRESS
LOAD T3,TLTYP,(T2) ;GET TYPE
CAIE T3,TT.MCB ;AN NVT?
JRST CHKNV1 ;NO
JE TTOTP,(T2),CHKNV1 ;OUTPUT ACTIVE?
LOAD T3,TINTL,(T2) ;YES, POKE OUTPUT
IDIVI T3,^D36
MOVE T4,BITS(T4)
IORM T4,TTSOQ(T3)
CHKNV1: LOAD T3,TINTL,(T2) ;POKE
IDIVI T3,^D36
MOVE T4,BITS(T4)
IORM T4,TNETRQ(T3)
RET
;LOCAL ROUTINE TO REQUEST SUBSEQUENT SERVICE
; T2/ DYNAMIC PTR
; PRESERVED ALL ACS
REQNS: SAVEAC <T3,T4>
JRST CHKNV1 ;GO SET THE BIT
;CONNECT TTY TO LL - "SET HOST" FUNCTION
; T1/ LL
; T2/ TTY LINE NUMBER
; T3/ FLAGS,,ESCAPE CHARACTER
; RETURN +1: FAILED, INVALID TTY LINE
; +2: OK
TTSETH::CALL STADYN ;CHECK LINE, GET TDB
RET ;FAILED, LINE NG
SETONE TTPRM,(T2) ;KEEP THIS BLOCK UNTIL LL RELEASED
STOR T3,TTUEC,(T2) ;SAVE ESCAPE CHAR
TXNE T3,SH%LPM ;"LOCAL" PAGE MODE?
IFSKP.
SETZRO TTNPM,(T2) ;NO
ELSE.
SETONE TTNPM,(T2) ;YES
ENDIF.
STOR T1,TTULL,(T2) ;SAVE LL
SETONE TTNUS,(T2) ;SAY LINE IN NETUSER STATE
LOAD T3,TINTL,(T2) ;GET LINE NUMBER
STOR T3,LLTTY,(T1) ;MAKE LL POINT TO TTY TOO
SETONE LLTTA,(T1) ;NOTE ACTIVE
CALL REQNS ;REQUEST SERVICE
RETSKP
;ASSIGN DECNET NVT, CONNECT IT TO LL
; T1/ LL
; RETURN +1: FAILED, NO LINES AVAILABLE
; +2: SUCCESS
ASMCB:: SAVEQ
MOVEM T1,Q2 ;SAVE LL
MOVE Q1,TT1LIN+TT.MCB ;GET FIRST MCB LINE
NOSKED ;FIND LINE RACE FREE
ASMCB1: LOAD T1,TTSTY,(Q1) ;GET LINE TYPE
CAIE T1,TT.MCB ;STILL MCB?
JRST [ OKSKED ;NO, NO LINES LEFT
RETBAD(ANTX01)]
MOVE T2,Q1
CALL STADYN ;SEE IF LINE AVAILABLE
JUMPE T2,ASMCB2 ;YES IF NO DATA BLOCK NOW ASSIGNED
ASMCB3: AOJA Q1,ASMCB1 ;STEP TO NEXT LINE
ASMCB2: MOVE T2,Q1
CALL TTYASC ;ASSIGN TDB
JRST ASMCB3 ;COULDN'T, TRY ANOTHER LINE
CALL STADYN ;SHOULD WORK NOW
JRST ASMCB3 ;??
SETONE TCJOB,(T2) ;INIT LINE
SETONE TTPRM,(T2) ;KEEP TDB UNTIL LL RELEASED
MOVE T1,Q2
STOR T1,TTHLL,(T2) ;SAVE LL
LOAD T3,TINTL,(T2) ;GET LINE NUMBER
STOR T3,LLTTY,(T1) ;KEEP IN LL
SETONE LLTTA,(T1) ;NOTE ACTIVE
MOVEI T1,.CHCNC
CALL TTCHID ;SEND CTRL-C TO START JOB
NOP
OKSKED
MOVE T1,Q1 ;RETURN LINE NUMBER
RETSKP
;CLEAR OUTPUT BUFFER - SEND ROTO-ROOTER DOWN LINE
; T2/ DYNAMIC PTR
MCCOBF: RET
;SEND XON - SEND ALLOCATION TO ALLOW USER TO SEND MORE INPUT IF NECESSARY
; T2/ STATIC PTR (LINE NUMBER)
MCSXON: RET
;SKIP IF OUTPUT BUFFER NOT EMPTY - CHECK FOR ALL ACKS, ETC.
; T2/ DYNAMIC PTR
MCSBEF: RET
;SEE IF SENDALL SHOULD HAPPEN ON SPECIFIED LINE
; T2/ STATIC PTR (LINE NUMBER)
; RETURN +1: SKIP THIS LINE
; RETURN +2: T2/ LINE NUMBER = DO THIS LINE
; T2/ -1 = SKIP ALL LINES OF THIS TYPE
MCCKSA: SKIPG TTACTL(T2) ;LINE ACTIVE?
RET ;NO, SKIP IT
RETSKP
;HANGUP - BREAK CONNECTION, ETC.
; T2/ STATIC PTR (LINE NUMBER)
MCHNGU: SAVEAC <T2>
CALL STADYN
RET ;ALREADY GONE
CALLRET TNHCLS ;FLUSH LL
;CHECK FOR OUTPUT POSSIBLE ON LINE
;OUTPUT NOT POSSIBLE IF LL HAS BEEN CLOSED
; T2/ DYNAMIC PTR
; RETURN +1: OUTPUT NOT POSSIBLE
; +2: OUTPUT OK
CKMCOU: TMNN TTHLL,(T2) ;LL STILL THERE?
RET ;NO
RETSKP ;YES
;ENABLE/DISABLE XOFF HANDLING IN USER SIDE
; T2/ DYNAMIC PTR
; TTFLGS(T2)/ TT%PGM BIT - ON IF LINE IN PAGE MODE
MCEXF: RET
;TURN LINE OFF ON RECEIPT OF XOFF
; T2/ DYNAMIC PTR
MCLNOF: RET
;TURN LINE ON AGAIN AFTER XOFF
MCLNON: RET
;CLOSE NET HOST CONNECTION
; T2/ TDB
TNHCLS: LOAD T1,TTHLL,(T2)
JUMPE T1,R ;IN CASE ALREADY GONE
NOSKD1 ;NO SCHEDULING
CALL TNTCLS ;PUT LL ON RELEASE QUEUE
CHNOFF DLSCHN ;TURN OF CHANNEL
CALL TTCOB5 ;FLUSH OUTPUT (DOES CHNON AND OKSKD1)
SETZRO TTOTP,(T2) ;CLEAR ACTIVE
SETZRO TTHLL,(T2)
;**;[3002] Add 1 line after TNHCLS:+7 DML 24-AUG-83
SETZRO TTPRM,(T2) ;[3002] BLOCK NO LONGER PERMANENT
RET
;Clear user state - called if LL being closed.
; T1/ LL
; CALL TTCLSH
;Return +1 always.
TTCLSH::LOAD T2,LLTTY,(T1) ;GET LINE NUMBER
CALL STADYN
RET ;ALREADY GONE
SETZRO TTULL,(T2) ;CLEAR EVERYTHING
SETZRO TTNUS,(T2)
;**;[3002] Replace 1 line with 4 at TTCLSH:+5 DML 24-AUG-83
CALL CTYMCB ;[3002] CTY OR MCB LINE?
IFSKP. ;[3002]
SETZRO TTPRM,(T2) ;[3002] NO, BLOCK NO LONGER PERMANENT
ENDIF. ;[3002]
RET
;CLOSE NET USER CONNECTION
; T2/ DYNAMIC PTR
TNUCLS: LOAD T1,TTULL,(T2) ;GET LL
SETZRO TTULL,(T2)
; ..
;CLOSE NVT
;ACCEPTS: T1/ LL
; T2/ TDB
;RETURNS: +1
;PRESERVES T2
TNTCLS: LOAD T3,LLLNK,(T1) ;GET THE LINK ID
IFN CZQDBG,< ;IF DEBUG
MOVEM T2,@CZQPTR ;SAVE TTY BLK
HRLM T3,@CZQPTR ;SAVE LL ID
AOS CZQPTR
CAIL T4,CZQBF+LCZQBF ;AT END OF BFR?
MOVEI T4,CZQBF ;YES, WRAP
HRRM T4,CZQPTR
>
;**;[3002] Delete 1 line at TNTCLS:+9 DML 24-AUG-83
SETZRO LLTTA,(T1) ;TTY NO LONGER ACTIVE ON THIS LL
SETZ T1, ;MAKE AOBJN
HRLI T1,-NTTMCB ; WORD
SKIPE ULLCZQ(T1) ;THIS ENTRY FREE?
AOBJN T1,.-1 ;NO
MOVEM T3,ULLCZQ(T1) ;YES, PUT IN LINK ID FOR NSPTSK
RET ;DONE
;SEND BYTES FROM TTY OUT BUFFER TO NET
; T2/ TTY DYNAMIC DATA BLOCK ADDRESS
; RETURN +2 TO PREVENT NORMAL OUTPUT START ACTION
MCSTRO: ACVAR <LL,MB,TDB,W1,W2> ;LL - LOGICAL LINK BLOCK
;MB - MESSAGE BUFFER
;TDB - TERMINAL DATA BLOCK
;W1, W2 - WORK REGS
STKVAR <ST3>
MOVEM T2,TDB ;SAVE TTY BLOCK ADR
LOAD LL,TTHLL,(TDB) ;GET LGL LINK FOR THIS LINE
JUMPE LL,RSKP ;PERHAPS GONE
LOCK LLLLCK,<JRST MCSOZ> ;LOCK OR GIVE UP
MOVE T1,LL
CALL BLKLOK ;LOCK LL
JRST [ UNLOCK LLLLCK ;COULDN'T
JRST MCSOZ]
UNLOCK LLLLCK
MCSO1: LOAD T3,LLSTA,(LL) ;CHECK LL STATE
CAIE T3,LLSRUN ;RUNNING?
JRST [ CALL REQNS ;FORCE INPUT CHECK, WILL DO SHUTDOWN
JRST MCSOX]
CALL SNDCHK ;CAN SEND ANOTHER SEG ON THIS LL?
IFNSK. ;NOT NOW
SKIPG TTOCT(TDB) ;OUTPUT READY TO GO?
JRST MCSOX ;NO, GO AWAY
JRST MCSOQ ;YES, SET TTSOQ BIT
ENDIF.
LOAD W2,LLSWG,(LL) ;GET SEG SIZE
MOVEI T1,<<MSHDR+DTMLEN>*4+3>(W2) ;GET SIZE OF BLOCK NEEDED
LSH T1,-2 ;IN WORDS
CALL GETRES ;GET MSG BLOCK
JRST MCSOQ ;CAN'T
MOVEM T1,MB ;SAVE IT
MOVE T2,TDB
CALL TTSND ;SEE IF HAVE AT LEAST ONE CHAR TO GO
JRST [ MOVE T1,MB ;NOTHING TO GO, RELEASE BLOCK
CALL RELRES
JRST MCSOX]
SETONE TTOTP,(T2) ;NOTE OUTPUT ACTIVE
MOVEM T1,ST3 ;YES, SAVE IT
MOVEI W1,MSHDR(MB) ;POINT TO DATA AREA
HRLI W1,(POINT 8,0)
MOVEM W1,LLBPTR(LL) ;SETUP POINTER FOR USE BY SUBROUTINES
SETZM LLBPCT(LL)
SETONE LLFEM,(LL) ;NOTE EOM NEEDED
MOVE T1,LL
SETZ T2,
CALL MAKFLG ;SETUP FLAGS
MOVE T3,MB
SETZ T4, ;INITIAL COUNT
CALL MAKMSG ;HEADER ITEMS
MOVE T2,TDB ;SETUP FOR TTSND
MOVE T1,ST3 ;GET FIRST CHAR TO GO
MCSO2: IDPB T1,LLBPTR(LL) ;STORE CHAR IN MSG
AOS LLBPCT(LL)
SOJLE W2,MCSO3 ;COUNT CHARS, JUMP IF DONE
CALL TTSND ;GET ANOTHER CHAR
IFSKP.
SETONE TTOTP,(T2)
JRST MCSO2
ENDIF.
SETONE TTOTP,(T2) ;NO MORE OUTPUT, BUT KEEP FLAG SET UNTIL ACK
MCSO3: MOVEI T3,MSDAT ;SAY THIS IS A DATA MSG
STOR T3,MSTOM,(MB)
LOAD T1,LLSWG,(LL) ;MAX SIZE
SUB T1,W2 ;LESS ANY NOT USED
ADDI T1,2 ;PLUS AN ARBITRARY NUMBER...
STOR T1,MSDTC,(MB) ;SET ACTUAL SIZE
DMOVE T1,LL ;PASS LL AND MB
CALL SNDSEG ;SEND IT
JRST MCSO1 ;TRY FOR MORE
;HERE WHEN CAN'T SEND BECAUSE FLOW CONTROL OR NO RES FREE OR LOCK LOCKED
MCSOQ: MOVE T1,LL
CALL BLKULK ;UNLOCK LL
MCSOZ: LOAD T2,TINTL,(TDB) ;GET LINE NUMBER
IDIVI T2,^D36
MOVE T3,BITS(T3)
IORM T3,TTSOQ(T2) ;SET BIT TO CHECK LINE AGAIN
RETSKP
;HERE WHEN NO MORE TO SEND
MCSOX: MOVE T1,LL
CALL BLKULK ;UNLOCK LL
RETSKP
ENDSV. ;END STKVAR
ENDAV. ;END ACVAR
;NET USER - MOVE CHARS FROM TTY IN-BUFFER TO NET
; T2/ DYNAMIC PTR
TNUSND: ACVAR <LL,MB,TDB,W1,W2> ;LL - LOGICAL LINK BLOCK
;MB - MESSAGE BUFFER
;TDB - TERMINAL DATA BLOCK
;W1, W2 - WORK REGS
STKVAR <ST3>
MOVEM T2,TDB ;SAVE TTY BLOCK ADR
LOAD LL,TTULL,(TDB) ;GET LGL LINK FOR THIS LINE
LOCK LLLLCK,<JRST TTUSY> ;LOCK OR GIVE UP
MOVE T1,LL
CALL BLKLOK ;LOCK LL
JRST [ UNLOCK LLLLCK ;COULDN'T
CALL REQNS ;TRY AGAIN LATER
JRST TTUSY]
UNLOCK LLLLCK
TTUS3: LOAD T3,LLSTA,(LL) ;CHECK LL STATE
CAIE T3,LLSRUN ;RUNNING?
JRST [ MOVE T1,LL ;NO, BEING CLOSED
CALL BLKULK ;UNLOCK LL
LOAD T1,TTUEC,(TDB) ;GET ESC CHAR
MOVE T2,TDB
CALL TTCHID ;GIVE IT AS INPUT
NOP
RET] ;DONE
SKIPLE TTICT(TDB) ;ANYTHING IN TTY BFR?
CALL SNDCHK ;CAN SEND ANOTHER SEG ON THIS LL?
JRST TTUSX ;NO, NSP WILL NOTIFY WHEN OK AGAIN
LOAD W2,LLSWG,(LL) ;GET SEG SIZE
MOVEI T1,<<MSHDR+DTMLEN>*4+3>(W2) ;GET SIZE OF BLOCK NEEDED
LSH T1,-2 ;IN WORDS
CALL GETRES ;GET MSG BLOCK
JRST [ MOVE T2,TDB
CALL REQNS ;CAN'T, REQUEUE TO TRY AGAIN LATER
JRST TTUSX]
MOVEM T1,MB ;SAVE IT
MOVEI W1,MSHDR(MB) ;POINT TO DATA AREA
HRLI W1,(POINT 8,0)
MOVEM W1,LLBPTR(LL) ;SETUP POINTER FOR SUBROUTINES
SETZM LLBPCT(LL)
SETONE LLFEM,(LL) ;NOTE EOM NEEDED LATER
MOVE T1,LL
SETZ T2,
CALL MAKFLG ;SETUP FLAGS - MAKFLG(T1,T2)
MOVE T3,MB
SETZ T4, ;INITIAL COUNT
CALL MAKMSG ;HEADER ITEMS - MAKMSG(T1,T2,T3,T4)
MOVE T2,TDB
TTUS1: CALL GTTCI ;GET IT
JRST TTUS2 ;NOTHING LEFT
IDPB T1,LLBPTR(LL) ;PUT IN MSG
AOS LLBPCT(LL)
SOJG W2,TTUS1
TTUS2: MOVEI T3,MSDAT ;SAY THIS IS A DATA MSG
STOR T3,MSTOM,(MB)
LOAD T1,LLSWG,(LL) ;MAX SIZE
SUB T1,W2 ;LESS ANY NOT USED
ADDI T1,2 ;PLUS AN ARBITRARY NUMBER...
STOR T1,MSDTC,(MB) ;SET ACTUAL SIZE
DMOVE T1,LL ;PASS LL AND MB
CALL SNDSEG ;SEND IT
JRST TTUS3 ;TRY FOR MORE
TTUSX: MOVE T1,LL
CALL BLKULK ;UNLOCK LL
TTUSY: MOVE T2,TDB ;RESTORE ARG
RET
ENDSV. ;END STKVAR
ENDAV. ;END ACVAR
;PERIODIC ROUTINE TO PROCESS NET USER AND NET HOST LINES
;CALLED FROM END OF TTCH7
MCSRV: SKIPL LLLLCK ;MASTER LOCK AVAILABLE?
RET ;NO, TRY AGAIN LATER
SAVEAC <Q1,Q2>
MOVSI Q1,-NTSQWD ;SCAN BIT TABLE FOR NET-USER LINES
TNET2: SKIPE T1,TNETRQ(Q1)
TNET4: JFFO T1,TNET1 ;JUMP IF ACTIVE LINE
AOBJN Q1,TNET2
RET
TNET1: MOVE Q2,BITS(T2) ;SAVE BIT FOUND
ANDCAM Q2,TNETRQ(Q1) ;CLEAR REQUEST
HRRZ T3,Q1 ;COMPUTE LINE NUMBER
IMULI T3,^D36
ADD T2,T3
CALL STADY ;SEE IF ACTIVE
JRST TNET3
CALL TINET ;SEE IF NVT INPUT
JE TTNUS,(T2),TNET3 ;JUMP IF NO LONGER IN NET USER STATE
SKIPE TTICT(T2) ;NET USER INPUT?
CALL TNUSND ;YES, TRY TO SEND IT
JE TTNUS,(T2),TNET3 ;JUMP IF NO LONGER IN NET USER STATE
CALL TNUREC ;SEE IF ANY NET USER OUTPUT RECEIVED
TNET3: MOVN T1,Q2 ;LOOK AT REST OF BIT WORD ONLY
ANDCA T1,TNETRQ(Q1)
JRST TNET4
;NET USER - RECEIVE OUTPUT FROM NETWORK IF POSSIBLE
; T2/ DYNAMIC PTR
TNUREC: LOAD T4,TTULL,(T2) ;GET LL
LOAD T4,LLSWG,(T4) ;GET MAX SIZE OF SEGMENT
LOAD T3,TOMAX,(T2) ;GET OUTBUF SIZE
CAIL T4,-2(T3) ;REASONABLE SEG SIZE?
MOVEI T4,-2(T3) ;NO, ASSUME OUTBUF SIZE -2
SUB T3,TTOCT(T2) ;COMPUTE REMAINING OUTBUF CAPACITY
CAIGE T3,2(T4) ;ROOM FOR ANOTHER?
JRST [ CALLRET REQNS] ;NO, REQUEST LATER SERVICE
MOVEI T1,TCOU1 ;ROUTINE TO PUT CHAR IN OUTPUT STREAM
LOAD T3,TTULL,(T2) ;LOGICAL LINK
CALL TTYFNT ;MOVE DATA FROM NET
JRST [ LOAD T1,TTUEC,(T2) ;LL GONE, SIMULATE ESCAPE CHAR
CALL TTCHID
NOP
RET]
JUMPN T1,TNUREC ;TRY AGAIN IF WE GOT SOMETHING
RET
;MOVE DATA FROM NETWORK TO TTY INBFR IF POSSIBLE
; T2/ DYNAMIC PTR
TINET: SAVEAC <T2,Q1,Q2>
MOVEM T2,Q2 ;SAVE DYNAMIC PTR
LOAD Q1,TINTL,(T2) ;GET LINE NUMBER
LOAD T1,TTSTY,(Q1) ;GET TYPE OF THIS LINE
CAIE T1,TT.MCB ;STILL MCB?
RET ;NO, DONE
TINET4: LOAD T3,TTHLL,(T2) ;LOGICAL LINK
JUMPE T3,TINET2 ;IN CASE GONE
REPEAT 0,<
;THIS CODE WILL PREVENT OVERFLOWING THE INPUT BUFFER. UNFORTUNATELY,
;IT WILL ALSO PREVENT ^C ETC FROM BEING SEEN. THEREFORE, IT CAN'T
;BE USED UNTIL WE HAVE AN NVT PROTOCOL THAT USES INTERRUPT MESSAGES
;TO GET AROUND BLOCKED-UP LL'S
LOAD T4,TIMAX,(T2) ;COMPUTE SPACE IN INBFR
SUB T4,TTICT(T2)
LOAD T1,LLSWG,(T3) ;MAX SEGMENT SIZE
CAMGE T4,T1 ;ROOM FOR ANOTHER SEGMENT?
JRST [ SETONE TTFWK,(T2) ;NO, WAKE UP ANY WAITING FORK
SAVEAC <FX>
CALL TTCH10
NOP
CALLRET REQNS] ;RECHECK LINE SOON
> ;END REPEAT 0
MOVEI T1,TTCHID ;ROUTINE TO PUT CHARS IN INPUT STREAM
CALL TTYFNT ;MOVE DATA FROM NET
JRST TINET3 ;LL DIED
REPEAT 0,<
;THIS CODE EXISTED FOR THE CONVENIENCE OF VMS USERS; IT ALLOWED THEM TO
;TYPE ANY CHARACTER TO BREAK THE NETWORK CONNECTION AFTER LOGGING OUT OF TOPS-20.
;OTHERWISE, THEY HAVE TO TYPE ^P AND EXIT FROM THEIR PROGRAM WHICH MAKES THE
;CONNECTION. IT WAS LATER DISCOVERED THAT THIS PRODUCES AN INCONSISTENCY IN
;TOPS-20'S HANDLING OF LINES ON WHICH THERE IS NO JOB. CG
LOAD T3,TCJOB,(T2) ;SEE IF JOB EXISTS
CAIE T3,-1
IFSKP.
ANDN. T1 ;NO, IF WE GOT SOMETHING,
JE TTBAC,(T2),TINET3 ;CLOSE LINK IF NOT BECOMING ACTIVE
ENDIF.
> ;END REPEAT 0
JUMPN T1,TINET4 ;YES, LOOP IF GOT ANYTHING THIS TIME
TINET2: RET
TINET3: CALL TNHCLS ;CLOSE NVT
MOVE T2,Q1 ;GET LINE NUMBER
CALL NTYCOF ;DO CARRIER OFF EVENT
LOAD T3,TCJOB,(Q2) ;GET CONTROLLING JOB
CAIE T3,-1 ;IS ONE?
JRST TINET2 ;YES, DONE
;**;[2646]MAKE CHANGES AT TINET3:+6L TAM 12-AUG-82
CALL STADYN ;[2646]GET DYNAMIC
RET ;[2646]FORGET IT
CALL TTCBF9 ;CLEAR OUTBUF
CALL TTYDED ;[2646]DEALLOCATE DATA BLOCK
NOP
JRST TINET2
;REMOVE SEGMENTS FROM ORDERED MESSAGE QUEUE AND MOVE DATA TO
;TTY BUFFERS
; T1/ ROUTINE TO DISPOSE OF CHARACTER
; T2/ TTY DYNAMIC BLOCK PTR
; T3/ LOGICAL LINK BLOCK
; RETURN +1: LINK NOT IN RUN STATE
; +2: OK
TTYFNT::TRVAR <MSGCNT,MSGBYP> ;*USED BY SUBROUTINES HEREIN*
ACVAR <LL,MB,TDB,W1,COR> ;LL - LOGICAL LINK BLOCK
;MB - MESSAGE BFR
;TDB - TERMINAL DATA BLOCK
;W1 - COUNT OF ALLOCATION RELEASED
;COR - CHARACTER OUT ROUTINE
MOVEM T1,COR
MOVEM T2,TDB ;SAVE TDB
MOVEM T3,LL
SETZ W1, ;INIT COUNT OF MESSAGES PROCESSED
LOCK LLLLCK,<JRST MCTYIY> ;LOCK OR GIVE UP
MOVE T1,LL
CALL BLKLOK ;LOCK LL
JRST [ UNLOCK LLLLCK ;COULDN'T
JRST MCTYIY]
UNLOCK LLLLCK
LOAD T3,LLSTA,(LL) ;CHECK LL STATE
CAIE T3,LLSRUN ;RUNNING?
JRST [ MOVE T1,LL ;NO
CALL BLKULK ;UNLOCK LL
MOVE T2,TDB ;RESTORE AC
RET] ;RETURN FAIL
SETZRO LLFIM,(LL)
MCTYI3: MOVE T1,LL ;SET UP FOR CALL
CALL TTGETS ;GET THE NEXT INCOMING SEGMENT
JRST MCTYI5 ;NONE THERE
MOVE MB,T2 ;GET THE SEGMENT ADDRESS RETURNED
LOAD T3,MSDTC,(MB) ;GET BYTE COUNT
MOVEM T3,MSGCNT
MOVE T3,MSBPTR(MB) ;AND PTR
MOVEM T3,MSGBYP
CALL GETTWO ;GET FLAGS
NOP
TXNE T2,ACKIND ;ACK PIGGYBACKED HERE?
CALL GETTWO ;YES, SKIP IT
NOP
LOAD T2,MSMFL,(MB)
TXNE T2,DATEOM ;END OF MSG?
JRST [ SETONE LLFIM,(LL) ;YES
JRST .+1]
JE LLIMS,(LL),MCTYI4 ;JUMP IF NO MSG FLOW CTRL
TMNE LLFIM,(LL) ;HAVE EOM?
MCTYI4: AOS W1 ;COUNT MESSAGE PROCESSED
MCTYI1: MOVE T2,TDB ;PASS TDB
SOSGE MSGCNT ;BYTE LEFT?
JRST MCTYI2 ;NO
ILDB T1,MSGBYP ;YES, MOVE IT
CALL 0(COR) ;CALL ROUTINE TO HANDLE CHARACTER
NOP ;IN CASE OF SKIP
JRST MCTYI1
MCTYI2: MOVE T1,LL ;SET UP
MOVE T2,MB ; FOR CALL
CALL TTREMS ;REMOVE SEGMENT FROM INCOMING MESSAGE QUEUE
MOVE T1,MB ;RETRIEVE SEGMENT ADDRESS
CALL RELRES ;RELEASE SPACE
DECR LLDMT,(LL) ;COUNT MESSAGES NOW IN QUEUE
JUMPE W1,MCTYI3 ;TRY AGAIN IF NOT EOM
MCTYI5: JUMPE W1,MCTYIZ ;DON'T ACK IF NOTHING PROCESSED
OPSTRM <ADDM W1,>,LLLSC,(LL) ;UPDATE OUTGOING FLOW COUNT
MCTYIZ: LOAD T3,LLLSC,(LL) ;SEE IF FLOW COUNT TO BE SENT
CAIG T3,FLOHLD ;ENOUGH TO BE WORTH SENDING?
JRST MCTYIX ;NO
MOVE T1,LL
CALL SQILS ;SEND IT
CALL [ MOVE T2,TDB ;COULDN'T, REQUEUE
CALLRET REQNS]
MCTYIX: MOVE T1,LL
CALL BLKULK ;UNLOCK LL
MCTYIY: MOVE T1,W1 ;RETURN ALLOC COUNT RELEASED
MOVE T2,TDB ;AND TDB
RETSKP
;GET TWO BYTE FIELD
;CLOBBERS T3, PRESERVES T4
GETTWO: GETBYM (MSGCNT,MSGBYP,R) ;GET A BYTE, RETURN IF NONE
LSHC T2,-10 ;SAVE LOW ORDER BYTE
GETBYM (MSGCNT,MSGBYP,R) ;GET NEXT ONE
LSHC T2,10 ;COMBINE BYTES
RETSKP ;AND DONE
ENDAV. ;END ACVAR
ENDTV. ;END TRVAR
> ;END IFN .MCFLG WAY BACK
IFE .MCFLG,<
;ROUTINES THAT SHOULDN'T BE CALLED IF NO MCB CODE
CHKLLT::
TNUCLS:
REQNS: BUG(NOMCCD)
>
;THIS SOFTWARE IS FURNISHED UNDER A LICENSE AND MAY ONLY BE USED
; OR COPIED IN ACCORDANCE WITH THE TERMS OF SUCH LICENSE.
;
;COPYRIGHT (C) 1976,1977,1978,1979 BY DIGITAL EQUIPMENT CORPORATION, MAYNARD, MASS.
IFN .FEFLG,< ;BULK OF FE CODE
SUBTTL FRONT-END DEPENDENT CODE
;FRONT-END DEPENDENT CODE FOR TTYSRV
;THIS MODULE IS NECESSARY TO SUPPORT THE KL10 -DTE20 INTERFACE
;FOR TTYSRV. IT DOES ALL THE DEVICE SPECIFIC FUNCTIONS AND
;PROCESSES DATA TO AND FROM THE FRONT END.
;DEFINITIONS FOR TTDEV FOR FE TYPE LINES
;DEFINITIONS FOR TT.FE LINE TYPE
DEFSTR TTFCT,TTDEV,27,8 ;NUMBER BYTES IN FRONT END
DEFSTR TTFMC,TTDEV,35,8 ;MAX BYTES IN FRONT END
SPCLIN==4 ;HIGHEST SPECIAL LINE NUMBER
RS TOTFCT,1 ;TOTAL BYTES IN FE
RS MAXFCT,1 ;TOTAL CAPACITY OF FE
COMMENT ! ;FOR INFO ONLY, ACTUAL DEFS IN PROKL
;THE FRONT END FUNCTION CODES
.DFLCI==1 ;LINE COUNT IS
.DFHSD==:3 ;HERE IS STRING DATA
.DFHLC==:4 ;HERE ARE LINE CHARACTERS
.DFRDS==:5 ;REQUEST DEVICE STATUS
.DFSDO==:6 ;SPECIAL DEVICE OPERATION
.DFLPC==1 ;LOAD PAGE COUNTER
.DFSTS==:7 ;HERE IS DEVICE STATUS
.DFESD==:10 ;ERROR ON DEVICE
.DFRTD==:11 ;REQUEST TIME OF DAY
.DFHTD==:12 ;HERE IS TIME OF DAY
.DFFDO==:13 ;FLUSH OUTPUT (SENT TO 11 ONLY)
.DFSTA==:14 ;SEND TO ALL (SENT TO 11 ONLY)
.DFLDU==:15 ;A LINE DIALED UP (FROM 11 ONLY)
.DFLHU==:16 ;A LINE HUNG UP OR LOGGED OUT
.DFLBE==:17 ;LINE BUFFER BECAME EMPTY
.DFXOF==:20 ;XOF COMMAND TO THE FE
.DFXON==:21 ;XON COMMAND TO THE FE
.DFSPD==:22 ;SET TTY LINE SPEED
.DFHLA==:23 ;HERE IS LINE ALLOCATION
.DFHRW==:24 ;HERE IS -11 RELOAD WORD
.DFACK==:25 ;GO ACK ALL DEVICES AND UNITS
.DFTOL==:26 ;TURN OFF/ON LINE
.DFTLO==:0 ;TURN IT OFF
.DFTOO==:1 ;TURN IT ON
.DFEDR==:27 ;ENABLE/DISABLE DATASETS
.DFLTR==:30 ;LOAD TRANSLATION RAM
.DFLVF==:31 ;LOAD VFU
.DFMSG==:32 ;SUPPRESS SYSTEM MESSAGES TO TTY
.DFKLS==:33 ;SEND KLINIK DATA TO THE -11
.DFXEN==:34 ;ENABLE XON (SENT TO 11 ONLY)
.DFBKW==:35 ;BREAK-THROUGH WRITE
.DFDBN==:36 ;DEBUG MODE ON
.DFDBF==:37 ;DEBUG MODE OFF
!
RESCD
; CLEAR OUTPUT BUFFER ROUTINE
TTCOB4: STKVAR <TTCBSV>
MOVEM B,TTCBSV ;SAVE ADDRESS OF DYNAMIC DATA
DYNST ;GET LINE NUMBER
MOVE D,B ;GET COPY OF LINE NUMBER
MOVS C,B ;LINE NUMBER
MOVEI B,.FEDLS ;GET DEVICE CODE
MOVE A,MSTRDT ;MASTER DTE, NO POST
CALL FIXARG ;GET PROPER ARGS
EXCH D,TTCBSV ;GET BACK DYNAMIC DATA
TMNE TTOTP,(D) ;OUTPUT IN PROGRESS?
JRST [ EXCH D,TTCBSV ;YES. GET BACK ORIGINAL ARGUMENT
CALL DTEFLO ;YES, FLUSH DTE REQUESTS
JRST TTCBF5]
EXCH D,TTCBSV ;GET BACK ORIGINAL ARGUMENT
TTCBF5: MOVS D,C ;LINE NUMBER AS ARG
SETZ C,
HRLI B,.DFFDO ;FLUSH FUNCTION
CALL DTEQI ;QUEUE IT UP
MOVE B,TTCBSV ;GET BACK DYNAMIC DATA
RET
ENDSV. ;END STKVAR
SWAPCD
; SET TERMINAL SPEED
TTSSP2:
;**;[3165]Add one line at TTSSP2: + 0L 10-SEP-84 TAB
TRVAR <LINENO> ;[3165]
MOVEM T2,LINENO ;[3165]SAVE LINE NUMBER
SKIPN FEFLG ;IN PRIMARY PROTOCOL?
RET ;NO. IGNORE IT THEN
ACVAR <W1,SSBFR>
UMOVE W1,2 ;GET FLAGS
TXNE W1,MO%AUT ;DECLARING AUTO SPEED?
JRST [ TXNE W1,MO%RMT ;YES. ALSO WANT REMOTE?
JRST .+1 ;YES. PROCEED THEN
RET] ;NO. ILLEGAL REQUEST
NOINT ;PREVENT INTS
BLCAL. ASGRSB,<[4],[.RESP3],[.RESTP]> ;GET A 4-WORD BLOCK
ITERR () ;SHOULDN'T HAPPEN
MOVEM A,SSBFR ;SAVE ADR OF BLOCK
MOVE C,A
HRLI C,(POINT 16,0) ;MAKE BYTE PTR
UMOVE D,C ;GET USER'S ARGS
HLRZ A,D ;GET INPUT SPEED
;**;[3165]Remove 6 lines at TTSSP2: + 16L 10-SEP-84 TAB
;**;[3165]Add 31 lines at TTSSP2: + 16L 10-SEP-84 TAB
;[3165]THE LAW OF SPEED SETTING:
;[3165] (1) IF MO%AUT=0 AND A LINE IS NOT REMOTE NOR AUTOBAUD, THEN SET TTSPWD
;[3165] AND ALSO SET SAVED SPEED IF ANY. THE SAVED SPEED IS ACTUALLY ONLY
;[3165] USED WHEN THE LINE IS GOING MO%RMT.
;[3165] (2) IN THE OTHER CASES, IF MO%AUT=0 THEN SET TTSPWD ONLY IF THERE IS
;[3165] A DYNAMIC DATA BLOCK. THIS COVERS THE CASE OF PRESERVING LINE
;[3165] SPEED WHEN A LINE IS REMOTE ONLY AND LEAVING SPEED ALONE IF
;[3165] A LINE IS AUTOSPEED AND NO DYNAMIC DATA EXISTS. WE SET THE SPEED
;[3165] IN THE FRONT-END IN THE REMOTE CASE.
;[3165] (3) OTHER CASES ARE MO%AUT=1, SPEEDS ARE IGNORED IN THIS CASE.
TXNE W1,MO%AUT ;[3165]IS MO%AUT ZERO?
IFSKP. ;[3165]
TMNE TT%AUT+TT%FEM,TTSTAT(B) ;[3165]YES, IS LINE NOT REMOTE NOR AUTO?
IFSKP. ;[3165]
MOVEM D,TTSPWD(B) ;[3165]YES, SET SPEED
CALL STADYN ;[3165](T2/T2) IS THERE DYNAMIC DATA?
ANSKP. ;[3165]IF NOT, PROCEED WITH SPEED SETTING
MOVEM D,TTSVPD(B) ;[3165]YES, SET SAVED SPEED
ENDIF. ;[3165]
;[3165]HERE FOR OTHER CASES WHERE MO%AUT=0
MOVE B,LINENO ;[3165]GET LINENO BACK
CALL STADY ;[3165]IS THERE DYNAMIC DATA
ANSKP. ;[3165]NO, DON'T CHANGE SPEED OF AUTOSPEED LINE
MOVE B,LINENO ;[3165]GET LINENO BACK
MOVEM D,TTSPWD(B) ;[3165]SET SPEED
ENDIF. ;[3165]
MOVE B,LINENO ;[3165]GET LINENO BACK
CALL TTEXFA ;SET XON/XOFF STATE
IDPB A,C ;STORE INPUT
IDPB D,C ;STORE OUTPUT SPEED
MOVEI D,0(D)
MOVEI A,1 ;ASSUME ONE STOP BIT
CAIG D,^D110 ;LESS THAN OR EQUAL TO 110 BAUD?
MOVEI A,2 ;YES. USE 2 STOP BITS THEN
TXNE W1,MO%RMT ;WANT REMOTE?
JRST [ MOVX D,SC%OPR!SC%WHL ;YES. SEE IF PRIVILEGED
TDNN D,CAPENB ;IS IT?
JRST TTSSP3 ;NO. ERROR
TRO A,(1B2) ;SET HIGH ORDER BIT
;**;[3165]Delete 1 line at TTSSP5: - 10L 10-SEP-84 TAB
SETONE TTFEM,(B) ;SAY IS REMOTE
TXNE W1,MO%AUT ;WANT "AUTO" SPEED?
JRST [ SETONE TTAUT,(B) ;SET INDICATOR
TRO A,(1B3) ;SET BIT IN MESSAGE TO FE
JRST TTSSP5] ;AND PROCEED
;**;[3165]Delete 4 lines at TTSSP5: - 2L 10-SEP-84 TAB
JRST .+1] ;GO SET SPEED ANYWAY
TTSSP5: IDPB A,C ;STORE THIS
MOVE C,SSBFR ;REFRESH PTR
HRLI C,(POINT 8,0)
MOVE F,SSBFR ;PASS BUFFER ADDRESS FOR INTERRUPT
BLCAL. TTDTEQ,<[SSPINT],[.DFSPD],[6],C>
TTSSP3: OKINT ;ALLOW INTS AGAIN
RET ;AND DONE
ENDTV. ;END TRVAR
ENDAV. ;END ACVAR
;HERE AT INTERRUPT LEVEL AFTER MSG SENT TO FE
; A/ UNIQUE CODE - ADR OF RESIDENT BFR
RESCD
SSPINT: CALL RELRES
RET
SWAPCD
; SET/RETURN DEVICE NON-TERMINAL STATUS
TTSNT1: SKIPN FEFLG ;IN PRIMARY PROTOCOL?
RET ;NO. IGNORE IT THEN
STOR C,TTNTS,(B) ;SAVE NEW VALUE
BLCAL. TTDTEQ,<[0],[.DFMSG],[0],C>
RET ;AND DONE
;ENABLE/DISABLE XOFF RECOGNITION IN THE FRONT-END
RESCD
TTEXFA: SAVET ;SAVE REGISTERS
CALL STADYN
RET ;NOT IMPORTANT
JRST TTEXZ
TTEXF: SKIPN FEFLG ;CHECK FOR PRIMARY PROTOCOL
RET ;NO. IGNORE IT THEN
SAVET ;SAVE TEMPS
TTEXZ: SETZ T4,0 ;ASSUME CLEAR
TMNE TT%PGM,TTFLGS(T2)
SETO T4,0 ;SET
DYNST ;GET STATIC TTY NUMBER
SKIPG TTACTL(T2) ;NORMALLY ACTIVE LINE?
SETZ T4, ;NO, DISABLE FE XOFF
BLCAL. TTDTEQ,<[0],[.DFXEN],[0],T4>
RET
SWAPCD
;TTMSG...
;CODE TO DO A SEND ALL FOR KL DTE20 CONFIGURATIONS
;TTMSSN FOR SINGLE LINE, TTMSAL FOR ALL LINES
; A/ BYTE PTR TO STRING
; B/ LINE NUMBER
; C/ COUNT OF BYTES IN STRING
TTMSAL: SASUBR <MSBP,MSLN,MSCT>
SKIPN FEFLG ;USING PRIMARY PROTOCOL?
JRST [ CAME B,CTYLNO ;CTY?
RET ;NO, FORGET IT
RETSKP] ;DO IT
SETOB B,MSLN ;NOTE ALL LINES
HRLI B,.DFSTA ;ASSUME SEND ALL
MOVSI A,DECSAL ;INTERRUPT LOCATION
HRR A,MSTRDT
HRRI B,.FEDLS ;THE LINE SCANNER
CALL FIXARG ;GO CHECK FOR CTY,ETC.
HRR C,MSCT ;THE COUNT
MOVE D,MSBP ;THE POINTER
TXO C,DTBYTM ;FORCE BYTE MODE SEND
AOS SALCNT ;INCREMENT SENDALL COUNT
CALL DTEQI ;GO SCHEDULE THE REQUEST
RETSKP
ENDSA.
;ROUTINE TO DO SENDALL FOR SINGLE LINE
; T2/ LINE NUMBER
; RETURN +1: DON'T DO THE LINE
; +2: OK TO DO, T2/ LINE NUMBER
TTMSSN: SKIPN FEFLG ;PRIMARY PROTOCOL?
CAMN T2,CTYLNO ;OR CTY?
RETSKP ;YES, OK TO DO
RET ;SKIP IT
RESCD
;TELL FE TO RESUME SENDING TO TERMINAL
TTXON1: SKIPN FEFLG ;IN PRIMARY PROTOCOL?
RET ;NO .SKIP THE MESSAGE THEN
;**;[2906] Add 2 lines at TTXON1: + 2L DSW 03-Feb-83
;**;[2909]Remove 2 lines at TTXON1: + 2L
;**;[3176]Put back 2 lines at TTXON1: + 2L TAB 1-NOV-84
JE TTXFF,(B),R ;[3176] IF NOT FORCING STATUS TO FE, RETURN
SETZRO TTXFF,(B) ;[3176] CLEAR THE BIT
MOVEI A,.DFXON ;FE XON FUNCTION
SAVEAC <B>
DYNST ;GET LINE NUMBER
CALLRET SNDFNC ;TELL FE TO RESTART
;FRONT END LINE. TELL FRONT END TO STOP SENDING TO TERMINAL
TTCHI3: SAVET ;SAVE TEMPS
;**;[2906] Add 2 lines at TTCHI3: + 1L DSW 03-Feb-83
;**;[2909]Remove 2 lines at TTCHI3: + 1L
;**;[3176]Put back 2 lines at TTCHI3: + 1L TAB 1-NOV-84
JE TTXFF,(B),R ;[3176] IF NOT FORCING STATUS TO FE, RETURN
SETZRO TTXFF,(B) ;[3176] CLEAR THE BIT
DYNST ;GET STAT ADDRESS
MOVEI A,.DFXOF ;TELL FE TO STOP
CALLRET SNDFNC ;DO IT
;ROUTINE TO SEND XOFF OR XON TO THE FRONT END
;ACCEPTS: A/ FUNCTION TO SEND
; B/ LINE NUMBER
;RETURNS: +1 /COULD NOT SEND REQUEST
; +2/ REQUEST SENT
SNDFNC: SAVEAC <B>
MOVSI C,0(B) ;PUT LINE NUMBER IN CORRECT PLACE
MOVSI B,0(A) ;FUNCTION CODE
HRRI B,.FEDLS ;ASSUME DLS
CALL FIXARG ;GO FIX UP THE ARGS
HLRZ D,C ;LINE NUMBER AS DATUM
SETZM C ;DIRECT
MOVE A,MSTRDT ;TO THE MASTER -11
CALLRET DTEQI ;QUEUE TO DTE
;SEND XOFF TO DISCOURAGE FURTHER INPUT FROM TERMINAL
SNDXO2: CONSZ PI,1B<^D20+DLSCHN> ;AT DTE PI LEVEL?
JRST SNDXO1 ;YES. GO TO IT
NOSKD1 ;PREVENT SCHEDULER INTERRUPTS
CHNOFF DLSCHN ;AND DTE INTERRUPTS
SNDXO1: SAVET
;**;[2904]Add 2 lines at SNDXO1: + 1L DSC 23-JAN-83
SKIPG TTACTL(B) ;[2904]LINE ACTIVE?
JRST SNDXO3 ;[2904]NO, SEND NOTHING
JN TTFXO,(B),SNDXO3 ;DO NOTHING IF PREVIOUS XOFF SENT
SETONE TTFXO,(B) ;SAY X-ON NEEDED
MOVEI D,XOFFC ;THE CHARACTER
SKIPGE CHITAB(D) ;PARITY NEEDED?
TXO D,200 ;YES. APPLY IT
MOVE A,MSTRDT ;SEND TO THE MASTER
MOVSI C,0(B) ;LINE NUMBER
;**;[2875]CHANGE 1 LINE AT SNDXO1:+8L TAM 9-DEC-82
MOVE B,[.DFBKW,,.FEDLS] ;[2875]
CALL FIXARG ;FIX UP THE ARGS
CALL DTEQI ;GO SEND IT
SNDXO3: CONSZ PI,1B<^D20+DLSCHN> ;AT DTE PI LEVEL?
RET ;YES. ALL DONE THEN
CHNON DLSCHN ;RESTORE THE CHANNEL
OKSKD1 ;AND THE SCHEDULER
RET ;AND DONE
;SEND XON ONLY IF LINE IS MARKED AS NEEDING
;ONE, AND IT HAS NOT STORED TOO MANY CHARACTERS IN EITHER ITS
;INPUT BUFFER OR TTBBUF
SNDXN2: JE TTFXO,(B),R ;IF NOT WAITING, RETURN
JN TTSHU,(B),R ;DO NOTHING IF LINE TURNED OFF
SAVET ;BE TRANSPARENT
STKVAR <SNDXSV>
MOVEM B,SNDXSV ;SAVE THE LINE NUMBER
;**;[3106] Add 1 line after SNDXN2:+4 DML 7-MAY-84
CONSO PI,77000 ;[3106] GO NOSKED ONLY AT PI LEVEL 7
NOSKD1 ;PREVENT SCHEDULER INTERRUPTION
CHNOFF DLSCHN ;AND DTE INTERRUPTS
LOAD A,TTFBB,(B) ;GET NUMBER CHARS IN TTBBUF
;**;[2904]Change 1 line at SNDXN2: + 8L DSC 23-JAN-83
SKIPG TTACTL(B) ;[2904]ACTIVE LINE?
JRST SNDXN1 ;NO, SEND NOTHING
CAIL A,MXBBC1 ;STILL TO MUCH IN BBUF?
JRST SNDXN1 ;YES, NO XON YET
CALL STADY ;GET ADDRESS OF DYNAMIC DATA
JRST SNDXN3 ;NOT ACTIVE. INPUT BUFFER CAN'T OVERFLOW
MOVEI A,MINXON ;LEVEL AT WHICH TO START AGAIN
CAMGE A,TTICT(B) ;IS INPUT BUFFER THIS FULL?
JRST SNDXN1 ;YES. DON'T SEND XON
;XON IS TO BE SENT. TELL DTE SERVICE
SNDXN3: MOVE B,SNDXSV ;TURN IT ON IF NOT ACTIVE.
MOVE A,MSTRDT ;TO THE MASTER
MOVEI D,XONC ;THE CHARACTER
SKIPGE CHITAB(D) ;PARITY NEEDED?
TXO D,200 ;YES. APPLY IT
MOVSI C,0(B)
;**;[2875]CHANGE 1 LINE AT SNDXN3:+6 TAM 9-DEC-82
MOVE B,[.DFBKW,,.FEDLS] ;[2875]
CALL FIXARG
CALL DTEQI ;GO SEND THE BYTE
MOVE B,SNDXSV ;GET LINE NUMBER
SETZRO TTFXO,(B) ;NO X-ON NEEDED NOW
SNDXN1: MOVE B,SNDXSV ;RESTORE LINE NUMBER
CHNON DLSCHN ;RESTORE DTE
;**;[3106] Add 1 line after SNDXN1:+1 DML 7-MAY-84
CONSO PI,77000 ;[3106] GO OKSKED ONLY AT PI LEVEL 7
OKSKD1 ;AND THE SHCEDULER
RET ;AND DONE
ENDSV. ;END STKVAR
;THIS IS A FRONT END LINE
TTHU2: SAVET ;SAVE TEMPS
MOVE A,MSTRDT ;MASTER -11, NO INT
MOVS C,B
MOVE B,[.DFLHU,,.FEDLS] ;HANG UP THIS LINE
CALL FIXARG
HLRZ D,C
SETZ C,
CALL DTEQI ;REQUEST THE HANGUP
RET ;AND DONE
;CHECK INPUT RATE OF LINE
;LIMIT ITS STORAGE IN TTBBUF
BIGST2: LOAD C,TTFBB,(B) ;GET COUNT OF CHARACTERS IN TTBBUF
AOS C ;INCREASE IT
CAIL C,MAXABC ;BEYOND BAD GUY CUTOFF?
JRST STPLNF ;STOP LINE
CAIG C,2 ;CHECK FOR 2 IN BUFFER
JRST BIGST4 ;NO NOT THIS TIME
SKIPG TTACTL(T2) ;YES CHECK TO SEE IF ACTIVE
JRST STPLNF ;NO SHUT LINE DOWN IT IS ANOYING ME
BIGST4: STOR C,TTFBB,(B) ;UPDATE COUNT OF CHARACTERS IN TTBBUF
CAIGE C,MAXBBC ;MANY CHARS FOR THIS LINE?
RETSKP ;NO, CONTINUE
MOVE C,TTBIGC ;YES, BIGBUF GETTING FULL TOO?
CAIL C,MAXABC-^D20
CALL SNDXO2 ;YES, SEND XOF
RETSKP
;TELL FE TO STOP ACCEPTING INPUT ON LINE, I.E. BY SETTING INPUT
;SPEED TO 0.
STPLNF: JN TTSHU,(B),R ;DO NOTHING IF LINE ALREADY OFF
SAVEAC <T2>
IFQE. TTWSO,(B) ;LINE HAS BEEN SHUT OFF BEFORE?
SETONE TTWSO,(B) ;NO, REPORT IT VIA BUGINF
BUG(TTYSTP,<<T2,LINE>>)
ENDIF.
SETONE TTSHU,(B) ;NOTE LINE SHUT OFF
MOVEI C,TTTOBL ;C/THE ROUTINE TO CALL
MOVEI A,^D5000 ;5 SECONDS
CALL TTQAD ;GO Q IT UP AND LOSE DATUM
MOVSI C,0(B) ;THE LINE
MOVE B,[.DFTOL,,.FEDLS]
MOVE A,MSTRDT ;TO THE MASTER
MOVEI D,.DFTLO ;TURN IT OFF
CALL FIXARG
CALL DTEQI ;OUTPUT IT
RET
;THIS CODE IS USED TO START UP A LINE TRANSFER VIA THE DTE20.
TTFES1: CALL TTSND ;GET ONE OUTPUT CHAR
RET ;BUFFER EMPTY
SKIPE FEFLG ;USING PRIMARY PROTOCOL?
IFSKP.
CALL [SAVEAC <B> ;NO
DYNST ;GET LINE NUMBER
CALLRET DTECHO] ;OUTPUT VIA SECONDARY
RET
SETONE TTOTP,(B) ;INDICATE LINE IS ACTIVE
RET ;AND DONE
ENDIF.
MOVE D,A ;THE CHARACTER
SETONE TTOTP,(B) ;SAY LINE IS ACTIVE
INCR TTFCT,(B) ;INCREASE COUNT OF BYTES IN -11
AOS TOTFCT ;MAINTAIN TOTAL OF ALL LINES
PUSH P,B ;SAVE ADDRESS OF DYNAMIC DATA
DYNST ;GET LINE NUMBER
SETONE TTFPK,(B) ;SAY WAITING FOR TO -11 DONE
MOVSI C,0(B) ;LINE NUMBER
MOVE B,[.DFHLC,,.FEDLS] ;ARGS
CALL FIXARG ;GET PROPER ARGS
PUSH P,F
SETZ F, ;JUST IN CASE
CALL DTSNGL ;GO DO A SINGLE REQUEST
JRST [ POP P,F ;FAILED. RESTORE FLAGS
POP P,B ;RESTORE ADDRESS OF DYNAMIC DATA
DECR TTFCT,(B) ;DECREMENT BYTES IN -11
SOS TOTFCT
CALL BAKTTO ;BACKUP TTY OUTPUT
JRST INTRST] ;GO SCHEDULE RETRY
POP P,F ;RESTORE FLAGS
POP P,B ;ADDRESS OF DYNAMIC BLOCK
RET ;AND DONE
;TTTOBL - ROUTINE CALLED FROM SCHEDULER TO TURN ON LINE AGAIN
;ACCEPTS:
; T2/ INTERNAL LINE NUMBER
TTTOBL: JE TTSHU,(B),R ;IF ALREADY RESTARTED, DO NOTHING
SETZRO TTSHU,(B)
BLCAL. TTDTEQ,<[0],[.DFTOL],[0],[.DFTOO]>
;TURN ON LINE
CALLRET SNDXN2 ;ASSUME AN X-ON IS NEEDED
; ENABLE/DISABLE TTY'S
FEDABL: SETZ C,0 ;SET LINE # (ALL)
MOVE A,MSTRDT ;GET ID OF MASTER
MOVE B,[.DFEDR,,.FEDH1] ;ENABLE/DISABLE DATASETS
CALL DTEQI
RET
SUBTTL FRONT-END TERMINAL HANDLING
RESCD ;MUST BE RESIDENT
;THIS ROUTINE IS CALLED FROM THE DTE20 INTERRUPT ROUITNE TO COMPLETE
;A TTY OUTPUT REQUEST. INPUT IS:
; A/ UNIQUE CODE (SEE BELOW)
; B/UNIT NUMBER
; C/DEVICE CODE
;UNIQUE CODE IS
; (0,,COUNT)
;WHERE COUNT IS THE NUMBER OF CHARACTERS SENT TO THE 11 IN SOME CALL TO
; DTEQ THAT SPECIFIED TTYINT AS ITS RETURN ADDRESS
; IF COUNT IS 0, THIS WAS A SINGLE CHARACTER (DTSNGL WAS CALLED)
; AND BUFFER COUNTS HAVE ALREADY BEEN UPDATED
; IF COUNT IS NON-ZERO, THIS WAS MULTIPLE CHARACTERS, AND THE BUFFER
; COUNT MUST BE UPDATED
;AT THIS POINT, THE CHARACTERS HAVE BEEN SENT TO THE 11 BUT NOT ACKNOWLEDGED
TTYINT::PUSH P,A ;SAVE UNIQUE CODE
MOVE A,C ;MOVE DEVICE TO A
CALL GETLIN ;GET PROPER CODE
JRST [ POP P,A ;RESTORE CODE
RET] ;AND GIVE UP
SETZRO TTFPK,(B) ;CLEAR WAITING FOR -11
POP P,A ;GET BACK UNIQUE CODE
CALL STADY ;GET ADDRESS OF DYNAMIC DATA
RET ;RETURN IF BECOMING ACTIVE OR INACTIVE
JUMPE A,TTYIN3 ;HAVE A COUNT?
;MULTIPLE CHARACTERS WERE SENT. UPDATE COUNT OF CHARACTERS IN OUTPUT
;BUFFER
MOVEI C,0(A) ;NUMBER OF CHARACTERS SENT
SUB C,TTOCT(B) ;COMPUTE NEW COUNT OF CHARACTERS IN BUFFER
SKIPG C ;IF COUNT WENT NEGATIVE, DON'T STORE IT
MOVNM C,TTOCT(B) ;STORE NEW COUNT
OPSTRM <ADDM A,>,TTFCT,(B) ;UPDATE FE CHAR COUNT
ADDM A,TOTFCT ;UPDATE TOTAL
CALL CHKWRN ;SEE IF FORK WAKEUP NEEDED
JRST TTYIN3 ;SEE IF MORE OUTPUT
;TTYINT..
;CALLED FROM SCHEDULER PERIODIC TASK PROCESSOR TO START OUTPUT FOR A LINE
; T2/ DYNAMIC PTR
; RETURN +1 ALWAYS
FESTRO: CHNOFF DLSCHN ;AVOID INTERRUPTS
SKIPE FEFLG ;PRIMARY PROTOCOL RUNNING?
IFSKP.
CALL TTFES1 ;NO, HANDLED BY 1-CHAR CASE
ELSE.
CALL TTYIN3 ;DO THE WORK
ENDIF.
CHNON DLSCHN
RETSKP ;NOTE NOTHING ELSE TO BE DONE
;CHARACTERS ARE IN OUTPUT BUFFER. CALL TTSND IF THERE IS ONLY ONE.
;OTHERWISE CALL DTEQ TO SEND THEM ALL
TTYIN3: STKVAR <TTYVR1,TTYVR2> ;GET SOME SAVE CELLS
CALL GETFMC ;GET LINE MAX ALLOCATION
LOAD D,TTFCT,(B) ;GET COUNT OF CHARS IN FE
CAML D,A ;ROOM FOR MORE?
JRST [ SETONE TTOTP,(B) ;SAY LINE IS WAITING FOR UNBLOCK
RET] ;AND GO DISMISS THIS INTERRUPT
JN <TTFLO,TTSAL,TTHPO,TTSFG,TTRXF>,(T2),[ ;ANY SPECIAL FLAGS?
CALLRET TTFES1] ;YES, HANDLED BY THE 1-CHAR CASE
SKIPN C,TTOCT(B) ;ANY OUTPUT CHARACTERS?
CALLRET TTFES1 ;NO
MOVE C,TTOOUT(B) ;GET POINTER
HRRZ A,C
TDNN C,WRPMSK ;NEED TO ADVANCE?
HRR C,1-TTSIZ(A) ;YES. DO IT
MOVE A,TTOCT(B) ;GET OUTPUT COUNT
CALL CNTSET ;GO ADJUST COUNT
MOVEM C,TTYVR1 ;SAVE STARTING BYTE POINTER
CALL FNDEND ;GO GET CHARACTERS
MOVE D,TTYVR1 ;GET BACK ORIGINAL BYTE POINTER
TRNN A,777776 ;AT LEAST TWO?
CALLRET TTFES1 ;NO. GO DO SINGLE CHARACTER
SETONE TTOTP,(B) ;MAKE SURE THIS IS ON
MOVEM C,TTOOUT(B) ;NEW OUTPUT POINTER
SETZ F, ;OUTPUT BUFFER
HRR F,A ;GET COUNT OF BYTES FOUND
MOVSI A,TTYINT ;IT'S TTY
HRR A,MSTRDT ;TO THE MASTER
MOVEM B,TTYVR2 ;SAVE ADDRESS OF DYNAMIC DATA
DYNST ;GET LINE NUMBER
SETONE TTFPK,(B) ;WAITING FRO TO -11 DONE
MOVS C,B ;LINE NUMBER
HRR C,F ;COUNT
MOVE B,[.DFHSD,,.FEDLS] ;STRING DATA
CALL FIXARG ;FIX UP THE ARGS
CALL DTEQ ;QUEUE THE REQUEST
JRST RSCHED ;GO DO RESCHEDULE
RET ;GO DISMISS THE INTERRUPT
;DTEQ FAILED. RESTORE COUNTS AND ARRANGE FOR SCHEDULER TO RESTART OUTPUT
RSCHED: MOVE B,TTYVR2 ;ADDRSS OF DYNAMIC DATA
MOVE D,TTYVR1 ;GET ORIGINAL BYTE POINTER
MOVEM D,TTOOUT(B) ;RESTORE OUTPUT BYTE POINTER
INTRST: DYNST ;B/ LINE NUMBER
SETZRO <TTOTP,TTFPK>,(B) ;NOT WAITING FOR PACKET
MOVEI A,^D100 ;TRY AGAIN IN 100 MS.
MOVEI C,TTSN10 ;START UP AS SINGLE CHARACTER
CALLRET TTQAD ;GO DO IT
ENDSV. ;END STKVAR
;CNTSET - ROUTINE TO FIGURE OUT MAX COUNT ALLOWED IN STRING DATA FUNCTION
;INPUT: A/ TTY BUFFER COUNT
; B/ ADDRESS OF DYNAMIC DATA
;RETURNS +1 ALWAYS WITH: A/-MAX COUNT,,0
CNTSET: SASUBR <CA,CB>
CALL GETFMC ;GET MAX ALLOC FOR THIS LINE
LOAD D,TTFCT,(B) ;CURRENT FRONT END COUNT
SUB A,D ;COUNT ALLOWED TO SEND
CAMLE A,CA ;CAN DO ALL?
MOVE A,CA ;YES
MOVN A,A ;FOR AOBJN
HRLZM A,CA ;TO LH AND RETURN IT
RET ;AND DONE
;GET MAX FE ALLOC FOR LINE. DEPENDS ON SPEED OF LINE
; B/ DYN PTR
; RETURNS +1 ALWAYS,
; A/ MAX BYTE COUNT
GETFMC: SAVEAC <C>
LOAD A,TTFMC,(B) ;GET NOMINAL MAX
STALOD C,TTOSP,(B) ;GET LINE SPEED
CAIE C,-1 ;UNKNOWN?
CAIGE C,^D1200 ;OR LESS THAN 1200?
JRST [ ASH A,-2 ;YES, 1/4 ALLOC
RET]
CAIL C,^D9600 ;FAST?
IMULI A,2 ;YES, DOUBLE ALLOC
RET ;OTHERWISE, NORMAL ALLOC
;FNDEND - FIND END OF MESSAGE TO SEND TO TERMINAL
;ACCEPTS:
; T1/ AOBJN POINTER TO STEP THROUGH OUTPUT BUFFER
; T3/ POINTER FOR REMOVING CHARACTERS FROM OUTPUT BUFFER
; CALL FNDEND
;RETURNS +1: ALWAYS,
; T1/ UPDATED AOBJN PTR, RH CONTAINS NUMBER CHARS TO DO
; T3/ UPDATED POINTER TO OUTPUT BUFFER
FNDEND: TDNN C,WRPMSK ;TO THE NEXT?
RET ;YES. DONE FOR NOW
ILDB D,C ;GET NEXT BYTE
TRNE D,TTOESC ;ESCAPE CHARACTER?
JRST [ ADD C,[^D9B5] ;DECREMENT BYTE POINTER
TLNE C,(40B5) ;WENT INTO PREVIOUS WORD?
SUB C,[44B5+1] ;YES. CORRECT IT
RET] ;AND RETURN
AOBJN A,FNDEND ;NO. GET MORE
RET ;ALL EXHAUSTED
;ROUTINE TO SET SPEED OF LINE FROM VALUES SENT BY -11
;ACCEPTS:
; A/ DEVICE CODE
; B/ UNIT NUMBER
; C/ REMOTE INDICATOR
; D/ INPUT,,OUTPUT
TTSPST::CALL GETLIN ;GET INTERNAL LINE NUMBER
RET ;INVALID
JUMPE C,TTSPS1 ;IF NOT REMOTE, JUMP OFF
SETONE TTFEM,(B) ;IS REMOTE
TRNN C,(1B3) ;IS IT AUTO ALSO?
JRST TTSPS1 ;NO.
SETONE TTAUT,(B) ;YES. SET INDICATOR
TTSPS1: MOVEM D,TTSPWD(B) ;STORE IT
RET ;AND DONE
;ROUTINE TO HANDLE SIGNAL FROM A FE THAT ITS LINE BUFFER FOR
;A GIVEN LINE IS EMPTY. ACCEPTS:
; A/ DEVICE CODE
; B/LINE NUMBER
TTYDON::JUMPL B,DONALL ;IF NEG HE WANTS TO ACK THEM ALL
CALL GETLIN
RET ;ILLEGAL LINE
JN TTFPK,(B),R ;IF TO -11 DONE PENDING, GO AWAY
CALL STADY ;GET ADDRESS OF DYNAMIC DATA
RET ;GONE
LOAD C,TTFCT,(B) ;GET COUNT OUTSTANDING
MOVN C,C
ADDM C,TOTFCT ;REDUCE FE TOTAL
SETZRO TTFCT,(B) ;CLEAR COUNT OF BYTES IN -11
JE TTOTP,(B),R ;IS THIS LINE WAITING FOR THIS INT?
CALLRET TTYIN3 ;YES, CONTINUE OUTPUT TO THE LINE
;HERE WHEN FRONT END IS ACKING ALL UNITS
DONALL: STKVAR <SAVEE>
MOVSI C,NTTFE ;NUMBER OF FRONT END LINES
MOVNS C ;MAKE AOBJN POINTER
DONAL1: MOVEM C,SAVEE ;SAVE AOBJN POINTER
MOVEI B,0(C) ;B/LINE NUMBER
MOVEI A,.FEDLS ;ALL LINES ARE DLS
CALL TTYDON ;GO ACK THIS GUY
MOVE C,SAVEE
AOBJN C,DONAL1 ;DO ALL LINES
MOVE B,CTYLNO ;GET CTY LINE NUMBER
LOAD C,TTSTY,(B) ;GET LINE TYPE
CAIE C,TT.FE ;FRONT END LINE?
RET ;NO. DON'T ACK IT
SKIPGE B,CTYUNT ;B/UNIT NUMBER FOR CTY
RET ;NOT SET UP YET
MOVEI A,.FEDLS ;A/ DEVICE .FEDLS
CALLRET TTYDON ;GO ACK THE LINE
ENDSV. ;END STKVAR
;ROUTINE TO HANDLE A DIAL UP SIGNAL FROM THE FE
; A/DEVICE CODE
; B/LINE NUMBER
TTYDLU::CALL GETLIN ;GET PROPER LINE NUMBER
RET ;ILLEGAL LINE
MOVSI A,0(B) ;LINE NUMBER TO LH
HRRI A,DLSCXF+CARONB ;INDICATE CARRIER ON
CALLRET BIGSTO ;PUT IT IN BUFFER
;ROUTINE TO HANDLE HANG UP SIGNAL FROM FE
; A/DEVICE CODE
; B/LINE NUMBER
TTYHGU::CALL GETLIN ;GET LINE NUMBER
RET ;ILLEAGAL LINE
MOVSI A,0(B) ;TO LH
HRRI A,DLSCXF ;CARRIER TRANSITION
CALLRET BIGSTO ;STORE IT
;DEFINE THE PROTOCOL TRANSFER VECTOR
TTYDTV::0 ;NO STRING DATA
TTYDON ;ACK
0 ;NO STATUS
TTYSLA ;SET LINE ALLOCATION
R ;NO ERROR REPORTING
TTDTRM ;DETACH REMOTES ON RELOAD
;THIS ROUTINE IS CALLED FROM THE DTE INTERRUPT ROUTINE TO SET
;THE LINE ALLOCATION FOR A TTY LINE. ACCEPTS:
; 1/ DEVICE CODE
; 2/ ALLOCATION
; 3/ LINE NUMBER
TTYSLA::EXCH B,C ;GET ARGS IN PROPER PLACES
CALL GETLIN ;GET INTERNAL LINE NUMBER
RET ;ILLEGAL LINE
STOR C,TSFMC,(B) ;STORE NEW ALLOCATION
RET ;AND DONE
;IDCTY - IDENTIFY THE CTY
;ACCEPTS:
; T2/ UNIT NUMBER FOR THE CTY AS KNOWN BY THE FRONT END
; CALL IDCTY
;RETURNS +1: ALWAYS
;CALLED FROM DTE SERVICE WHEN THE FRONT END SENDS OVER THE UNIT NUMBER
;WITHIN THE .FEDLS DEVICE THAT IT KNOWS AS THE CTY. STORES:
;CTYUNT/ THE UNIT NUMBER
;CTYINT/ THE INTERNAL EQUIVALENT OF THAT (INTERNAL LINE NUMBER)
;THE CTY SHOULD ALWAYS BE ADDRESSED INTERNALLY BY CTYLNO, WHICH IS
;SET UP BY TTINIT. CTYINT WILL CONTAIN THE INTERNAL
;EQUIVALENT OF THE LINE ON WHICH THE CTY IS PHYSICALLY LOCATED FOR THIS
;MONITOR LOAD. ADDRESSING THE LINE BY THIS NUMBER IS AN ERROR.
;IF CTYINT=CTYLNO, CTYINT IS SET TO -1 SO THAT NO LINE NUMBER WILL
;EVER MATCH IT
IDCTY:: SAVET
PUSH P,T2 ;SAVE UNIT NUMBER
SETOM CTYUNT ;INDICATE CTY NOT KNOWN FOR GETLIN
MOVEI T1,.FEDLS ;T1/DEVICE
CALL GETLIN ;GET THE INTERNAL EQUIVALENT
RET ;NOT A FRONT END LINE
CAME T2,CTYLNO ;IS THIS ITS VALID INTERNAL LINE NUMBER?
MOVEM T2,CTYINT ;NO. SAVE THIS AS ITS ALIAS
POP P,CTYUNT ;SET UNIT NUMBER FOR CTY
RET
;GETLIN - ROUTINE TO CONVERT DEVICE/LINE TO INTERNAL LINE NUMBER
;ACCEPTS:
; A/DEVICE CODE (ONLY .FECTY OR .FEDLS)
; B/LINE NUMBER
;RETURNS +1: FAILURE
; +2: SUCCESS,
; T2/INTERNAL LINE NUMBER
;DOES NOT CLOBBER ANY REGISTERS EXCEPT B
GETLIN: CAIN A,.FECTY ;THE CTY?
JRST [ MOVE B,CTYLNO ;YES. USE INTERNAL NUMBER OF CTY
RETSKP] ;AND RETURN WITH GOOD LINE
;THE DEVICE MUST BE .FEDLS
CAMN B,CTYUNT ;THE UNIT NUMBER FOR THE CTY?
JRST [ MOVE B,CTYLNO ;YES. GET INTERNAL LINE NUMBER FOR CTY
RETSKP]
CAIL B,NTTFE ;IS THE UNIT NUMBER WITHIN THE NUMBER
; OF FRONT END LINES THAT WE KNOW ABOUT?
RET ;NO. CAN'T BE A FRONT END LINE
JUMPE B,GETLN1 ;IF THE DL11, SKIP BIAS
SUBI B,SPCLIN ;BIAS THE LINE
SKIPG B ;NOW A GOOD T/S LINE NUMBER?
ADDI B,NTTFE-1 ;NO. WAS A SPECIAL. TRANSLATE THE LINE #
GETLN1: ADD B,TT1LIN+TT.FE ;YES. ADD NUMBER OF FIRST F.E. LINE
RETSKP ;RETURN SUCCESS
;FIXARG - ROUTINE TO DETERMINE PROPER DEVICE/LINE NUMBER FOR LINE ON RSX20F
;FRONT END
;ACCEPTS: RH B/ DEVICE (ONLY .FEDLS)
; LH C/ INTERNAL LINE NUMBER
; CALL FIXARG
;RETURNS +1: ALWAYS,
; RH B/ DEVICE AS KNOWN BY THE FRONT END
; LH C/ UNIT AS KNOWN BY FRONT END
;CALLED IN PREPARATION FOR CALLING DTE SERVICE. LINE IS ASSUMED TO
;BE ON THE FRONT END
;NOTE: IF CALLED WITH -1, RETURNS IMMEDIATELY. THIS IS BECAUSE OF A
;FRONT-END BUG THAT REQUIRES RECEIVING -1 ON A SENDALL
FIXARG: ACVAR <W1> ;GET SOME WORK REGISTERS
JUMPL C,R ;IF UNIT .LE. 0, NO CHANGE
HLRZ W1,C ;GET INTERNAL LINE NUMBER
CAMN W1,CTYLNO ;THE CTY?
JRST [ HRRI B,.FECTY ;YES. USE THE CTY
HRLI C,0 ;AND UNIT 0
RET]
SUB W1,TT1LIN+TT.FE ;GET LINE NUMBER WITHIN TYPE
JUMPE W1,FIXAR1 ;IF THE DL11, ALL DONE
ADDI W1,SPCLIN ;NOT. BIAS THE LINE NUMBER
CAILE W1,NTTFE-1 ;A VALID T/S LINE?
SUBI W1,NTTFE-1 ;NO. ONE OF THE SPECIALS THEN
FIXAR1: HRL C,W1 ;RETURN IT IN LH OF C
RET ;AND DONE
ENDAV. ;END ACVAR
;LOCAL ROUTINE TO SIMPLIFY CALLS TO DTEQ - USES "BLISS" CALLING SEQUENCE
; T2/ LINE NUMBER
; CALL <AA,AB,AC,AD>
; WHERE: (SEE DTESRV FOR FURTHER DETAILS)
; AA - DRIVER INT LOC (ASSUME MASTER DTE)
; AB - DTE FUNCTION (ASSUME .FEDLS)
; AC - 0 ,, BYTE CNT (LH FILLED IN WITH LINE NUMBER)
; AD - DATUM
;RETURN +1: ALWAYS
; ALL ACS PRESERVED
TTDTEQ: BLSUB. <AA,AB,AC,AD>
SAVET
HRLZ C,B
HRLZ B,AB
HRRI B,.FEDLS
CALL FIXARG ;CONVERT LINE NUMBER
HRLZ A,AA
HRR A,MSTRDT
HRR C,AC
MOVE D,AD
CALLRET DTEQI ;USE NON-SKIP VERSION OF DTEQ
ENDBS.
;DTESTO - ROUTINE TO STORE A CHARACTER IN TTBBUF. CALLED AT INTERRUPT LEVEL
;FROM DTE SERVICE. DATA IS ALWAYS A CHARACTER AT THIS POINT.
;ACCEPTS:
; T1/CHARACTER IN 8 BITS
; T2/(0,, PHYSICAL LINE NUMBER)
; T3/DEVICE TYPE
;RETURNS +1: ALWAYS
DTESTO::EXCH C,A ;TYPE TO A, CHAR TO C
CALL GETLIN ;GET INTERNAL LINE NUMBER FOR THIS LINE
RET ;LINE NOT ON FRONT END
MOVE A,C ;RESTORE CHARACTER
CALLRET TTIDON ;GO STORE CHARACTER
;DEVICE DEPENDENT CODE FOR SOBE
;SKIP IF FE BUFFER NOT EMPTY
TTSBEF: JN TTFCT,(T2),RSKP ;LOCAL RETURN SKIP IF NON-EMPTY
RET ;EMPTY
;DEVICE DEPENDENT CODE FOR INIALIZING DYNAMIC STORAGE
TTSETF: LOAD T3,TSFMC,(T2) ;GET FRONT END CHARACTER LIMIT FROM DYNAMIC
STOR T3,TTFMC,(T1) ; AND COPY TO DYNAMIC
;**;[3172]Add 4 lines at TTSETF: + 2L 8-OCT-84 TAB
CAIN T4,MSGLEN ;[3172]IS THIS A MESSAGE-LENGTH BLOCK?
RET ;[3172]YES. NO MORE INITIALIZATION
MOVE T3,TTSPWD(T2) ;[3172]GET SPEED WORD
MOVEM T3,TTSVPD(T1) ;[3172]SAVE IN SAVED SPEED WORD
RET
;ROUTINE CALLED FROM PROTOCOL HANDLER TO DETACH ALL REMOTE JOBS FOR
;A GIVEN DTE. ACCEPTS:
; A/ DTE NUMBER (NOT USED)
;RETURNS +1 ALWAYS
SWAPCD ;IS SWAPPABLE
TTDTRM: CAME A,MSTRDT ;IS THIS FOR THE MASTER DTE?
RET ;NO. DON'T DO ANYTHING THEN
SAVET ;SAVE ALL TEMP REGISTERS
MOVSI B,NTTFE ;NUMBER OF FE LINES
MOVNS B ;SET UP AOBJN POINTER
HRR B,TT1LIN+TT.FE ;START WITH FIRST LINE AND LOOP THROUGH ALL
TTDTR1: TMNE TTFEM,(B) ;IS THIS LINE REMOTE?
CALL TTJBDT ;YES. DETACH IT THEN
AOBJN B,TTDTR1 ; DO ALL LINES
MOVEI A,.SFRMT ;SEE IF REMOTE LOGINS NOW ALLOWED
TMON ;GET VALUE
XCT [ CALL DTRMDS ;NOW DISALLOWED
CALL DTRMEN](B) ;NOW ALLOWED
RET ;AND DONE
;ROUTINE TO DEFINE THE DL11W PSEUDO-CTY'S.
;PRIMARY PROTOCOL MUST BE RUNNING
DFNDL1::ACVAR <W1> ;GET A WORK REG
STKVAR <<DFNDLS,2>,<DFNDS1,1>> ;A STRING
MOVE T2,[ASCII /TTY/] ;GET BASE STRING
MOVEM T2,DFNDLS ;SAVE IT
MOVE T2,[ASCIZ /DL0/] ;GET DEFINITION STRING
MOVEM T2,DFNDS1 ;SAVE IT
MOVE W1,[-<SPCLIN-1>,,SPCLIN-2] ;THE LINES TO DO
DFNDLL: HRRZ T2,W1 ;GET LINE NUMBER
MOVEI T1,.FEDLS ;FOR THE DLS DEVICE
CALL GETLIN ;GET ITS INTERNAL NUMBER
JRST DFNDLE ;?
SETONE TTIGI,(T2) ;SET IGNORE
MOVEI T1,DFNDLS ;GET ADDRESS OF BYTE ARRAY
HRLI T1,(<POINT 7,0,20>) ;MAKE IT A STRING POINTER
MOVEI T3,10 ;GET AN OCTAL NUMBER
NOUT ;PUT LINE NUMBER IN STRING
JFCL
MOVEI T3,":" ;GET TERMINATOR
IDPB T3,T1 ;STORE COLON
SETZM T3 ;GET A NULL
IDPB T3,T1 ;TIE OFF STRING
MOVX T1,<BYTE (7)0,0,1>
ADDM T1,DFNDS1 ;CHANGE LOGICAL NAME STRING
MOVEI T1,.TTDES(T2) ;GET DEVICE DESIGNATOR IN T1
MOVEI T2,.MOSNT ;SET NON-TERMINAL STATUS
MOVEI T3,.MOSMN ;SUPPRESS SYSTEM MESSAGES
MTOPR ;DO IT
ERJMP .+1 ;PROCEED IF IT FAILS
MOVX T1,.CLNSY ;CREATE SYSTEM LOGICAL NAME
HRROI T2,DFNDS1 ;THE LOGICAL NAME
HRROI T3,DFNDLS ;THE DEFINITION
CRLNM ;DO IT
DFNDLE: BUG (DLDEF)
AOBJN W1,DFNDLL ;DO THEM ALL
RET ;AND DOND
ENDSV. ;END STKVAR
ENDAV. ;END ACVAR
> ;END IFN .FEFLG MANY PAGES BACK
IFE .FEFLG,<
;DUMMY SYMBOLS
TTTOBL:
>
IFN .DZFLG,< ;BULK OF DZ CODE FOLLOWS
SUBTTL DZ11 DEVICE DEPENDENT CODE FOR SM10
; DZ11 TTY SERVICE MODULE FOR SM10 CONFIGURATIONS
EXTN <DZCHCT> ;SPECIAL "CLOCK" FOR PI CHECKS
;DEFINITIONS FOR TTDEV FOR DZ TYPE LINES
RESCD
SCDTMZ==^D50 ;TIME FOR RING CHECKS
DZTMCK==^D5000/SCDTMZ ;WHEN TO DO PI CHECK
DZCRDL==^D8000 ;TIME DELAY FOR CARRIER HANGUP
;START OUTPUT FOR DZ LINE
;CALLED FROM SCHED PERIODIC PROCESSING
; T2/ DYN PTR
; RETURN +1 ALWAYS
DZSTRO: CHNOFF DLSCHN
CALL DZSND1 ;START LINE
CHNON DLSCHN
RETSKP
; SEND CHARACTER TO LINE
; T2/ DYN PTR
; RETURN +1 ALWAYS
DZSND1: LOAD T3,TINTL,(T2) ;GET LINE NUMBER
CAME T3,KLILNO ;KLINIK?
JRST NOTDZK ;NOT KLINIK
JN KLIOVL,,R ;STILL BUSY
JN TTXOC,(T2),DZXOC ;XON/OFF REQUESTED?
CALL TTSND ;GET A CHAR
RET ;NONE THERE
STOR T1,KLIOCH ;STORE OUTPUT CHARACTER
SETONE KLIOVL ;SET VALID
JRST CTYCOM ;AND DO COMMON STUFF
NOTDZK: CAME T3,CTYLNO
JRST [ SKIPE DZLNCT ;IF NO DZ LINES MUST RETURN
SKIPN FEFLG ;SECONDARY PROTOCOL?
RET
JRST DZPRNC] ;NOT CTY BUT PRIMARY PROTOCOL
JN CTYOVL,,R
JN TTXOC,(T2),DZXOC ;XON/OFF REQUIRED?
CALL TTSND ;GET CHAR
RET ;NONE
STOR T1,CTYOCH ;SET OUTPUT CHARACTER
SETONE CTYOVL ;SET VALID CHARACTER AVAILABLE
CTYCOM: CALL INTETY ;INTERRUPT 8080
SETONE TTOTP,(T2) ;SET LINE ACTIVE
RET ;RETURN
;START OUTPUT ON DZ LINE
DZPRNC: SUB T2,DZLNOF ;SUBTRACT RESTRICTED LINES
CAMLE T2,DZLNNO ;LEGAL?
RET
CALL GETEXL ;GET EXTERNAL PAGE INFO
SETONE TTOTP,(T2) ;SET LINE ACTIVE
BSIOB T1,DZTCR(T3) ;REQUEST INTERRUPT ON LINE
RET
;SEND XON/XOFF ON CTY LINE
DZXOC: JN TTFXF,(T2),DZPRXO ;DO XON
DZPRXF: MOVEI T4,XOFFC ;GET XOFF CHARACTER
SKIPA ;COMMON
DZPRXO: MOVEI T4,XONC ;GET CHARACTER
SKIPGE CHITAB(T4) ;PARITY NEEDED?
TXO T4,200 ;YES, APPLY IT
SETZRO <TTXOC>,(T2) ;CLEAR FLAGS
CAMN T2,KLILNO ;KLINIK?
JRST [ STOR T4,KLIOCH ;YES STORE IN KLINIK BUFFER
SETONE KLIOVL ;SET VALID CHARACTER
JRST DZPRXA]
STOR T4,CTYOCH ;STORE CHARACTER IN 8080 BUFFER
SETONE CTYOVL ;SET VALID CHARACTER
DZPRXA: CALL INTETY ;INTERRUPT 8080
SETONE TTOTP,(T2) ;SET LINE ACTIVE
RET
DZBST: LOAD T3,TTFBB,(T2) ;GET COUNT
AOS T3 ;INCREASE COUNT OF CHARACTERS IN TTBBUF
CAIL T3,MAXABC ;OVER RUN?
RET ;YES, FLUSH CHAR
STOR T3,TTFBB,(T2) ;STORE COUNT
CAIL T3,MAXBBC ;CHECK FOR MAX BEFORE SHUT OFF
CALL DZSXOF ;SEND XOFF
RETSKP ;STORE CHARACTER
DZSXOF: SAVET
MOVEI T4,XOFFC ;GET XOFF CHARACTER
SETONE <TTXOC,TTFXO>,(T2) ;SET XOFF
SETZRO TTFXF,(T2)
JRST DZXCM ;GO TO COMMON STUFF
DZSXON: JE TTFXO,(T2),R ;XON ONLY IF REQUIRED
SAVET
PUSH P,T2 ;SAVE LINE NUMBER
CALL STADYN ;CONVERT TO DYNAMIC
JRST DZNXN ;FORGET IT
LOAD T4,TIMAX,(2) ;CAPACITY OF INPUT BUFFERS
SUBI T4,MINCT1 ;LESS AMOUNT BEFORE FORCED WAKEUP
CAMG T4,TTICT(2) ;BUFFER NOW THAT FULL?
JRST PB2 ;YES, WAIT
DYNST ;BACK TO STATIC ADDRESS
SETONE <TTXOC,TTFXF>,(T2) ;SET XON REQUIRED
SETZRO TTFXO,(T2) ;CLEAR OLD SWITCH
DZNXN: MOVEI T4,XONC ;GET XON CHARACTER
POP P,T2 ;RESTORE LINE NUMBER
DZXCM: SKIPGE CHITAB(T4) ;PARITY NEEDED?
TXO T4,200 ;YES, APPLY IT
CHNOFF DLSCHN ;SET CHANNEL OFF
CAMN T2,KLILNO ;KLINIK?
JRST [ JN KLIOVL,,DZCXR ;CHECK TO SEE IF READY
STOR T4,KLIOCH ;STORE CHARACTER
SETONE KLIOVL ;SET VALID
JRST DZXCM1]
CAME T2,CTYLNO ;CTY?
JRST DZXDZ ;REAL DZ
JN CTYOVL,,DZCXR ;CHECK TO SEE IF READY FOR A CHARACTER
STOR T4,CTYOCH ;SET OUTPUT CHARACTER
SETONE CTYOVL ;SET VALID
DZXCM1: SETZRO TTXOC,(T2) ;CLEAR BOTH SINCE ALL IS DONE
CALL INTETY ;INTERRUPT 8080
DZCXR: CHNON DLSCHN ;TURN CHANNEL BACK ON
RET ;AND RETURN
DZXDZ: PUSH P,T2 ;SAVE STATIC ADDRESS
CALL STADYN ;FIND DYNAMIC STORAGE ADDRESS
JRST DZDZX ;NOT SETUP YET FORGET IT
JN TTOTP,(T2),DZDZX ;QUIT IF BUSY (IT WILL GET CLEARED)
CALL GETEXL ;FIND EXTERNAL PAGE ADDRESS
SETONE TTOTP,(T2) ;SET LINE ACTIVE
BSIOB T1,DZTCR(T3) ;REQUEST INTERRUPT
DZDZX: CHNON DLSCHN
JRST PB2 ;AND QUIT
;DZINIT -- ROUTINE TO INITALIZE DZ11
;DZRSTR -- SAME ROUTINE TO RESTART DZ11
DZINIT: SAVEAC <Q1,Q2,P1> ;SAVE AN AC
SETZM CTYINT ;SET ALIAS (FOR NOW IT IS 0) FOR CTY
MOVE T4,SMTEPT+DZUBN ;FIND THE TRAP VECTORS
ADDI T4,DZ110V/4 ;OFFSET TO INTERRUPT VECTORS
MOVEI Q2,DZMAX ;FIND THE MAX DZ11
MOVE T2,[XPCW DZRDIB] ;SET INTERRUPT BLOCK
MOVE T3,[XPCW DZXINB] ;OUTPUT INTERRUPT BLOCK
SETZB Q1,P1 ;SET POINTER TO CORRECT BLOCK
DZIVLP: MOVEM T2,0(T4) ;MAKE AN ENTRY IN THE INTERRUPT VECTOR BLOCK
MOVEM T3,1(T4) ;GET OUTPUT INTERRUPT VECTOR
ADDI T3,4 ;FOUR WORDS PER INTERRUPT BLOCK
ADDI T4,2 ;POINT TO NEXT INTERRUPT BLOCK
MOVE T1,[MSEC1,,DZRDIN] ;SET UP THE INTERRUPT BLOCK
MOVEM T1,DZRDIB+3 ;SET UP VECTOR ADDRESS
SETZM DZRDIB+2 ;SET FLAGS TO 0
MOVE T1,[MSEC1,,DZTXIN] ;SET UP OUTPUT INTERRUPT BLOCK
ADD T1,Q1 ;POINT TO CORRECT INTERRUPT INST
MOVEM T1,DZXINB+3(P1)
SETZM DZXINB+2+(P1) ;SET FLAGS TO 0
ADDI Q1,3 ;3 INSTRUCTIONS PER LINE
ADDI P1,4 ;4 WORDS PER BLOCK
SOJN Q2,DZIVLP ;LOOP UNTIL DONE
MOVE T1,CTYINT ;GET CTY LINE NUMBER
AOS T1 ;MAKE KLINIK CTY+1
MOVEM T1,KLILNO ;SAVE KLINIK LINE NUMBER
RET
; RESTART CODE ALSO RUN FOR INITILIZATION IT SETS UP THE INTERRUPT ENABLES
DZRSTR: SAVEP ;SAVE THE P'S
MOVSI P1,-DZMAX ;MAXIMUM NUMBER OF DZ11'S TO HANDLE
MOVE P2,[DZ11BA] ;GET BASE ADDRESS OF DZ11
DZINLP: MOVE T1,P2 ;ADDRESS OF DZ11
CALL UBGOOD ;DOES IT EXIST ?
JRST DZNOUB ;NO
MOVEI T1,DZCLR ;INIT THE DZ11
WRIO T1,DZCSR(P2) ;RESET THE DZ
MOVSI T2,1 ;SET UP LOOP COUNT
DZCLRK: SOJE T2,[BUG(DZCLRB)]
TIOE T1,DZCSR(P2) ;WAIT FOR FINISH
JRST DZCLRK
MOVEI T1,DZRIEN+DZTIEN+DZMSCN ;SET INTERRUPT ENABLES AND SCANNER
WRIO T1,DZCSR(P2) ;START DZ11
ADDI P2,DZMNV ;ADD THE VECTOR SIZE
AOBJN P1,DZINLP ;AND TRY THE NEXT ONE
DZNOUB: HRRZM P1,DZLNCT ;SAVE NUMBER OF DZ11'S FOUND
IMULI P1,10 ;COUNT OF LINES
HRRZM P1,DZLNNO
MOVE T1,TT1LIN+TT.DZ
ADDI T1,FELNS ;ADD IN PSEUDO LINES
MOVEM T1,DZLNOF
RET ;RETURN
; DZHU0 -- ROUTINE TO SCHEDULE A HANGUP
DZHU0: SETZ T1, ;T1/ INDICATE DO IT IMMEDIATELY
MOVEI T3,DZHU2 ;T3/ ROUTINE TO HANGUP THE LINE
CALL TTQAD ;SCHEDULE HANGUP AS SOON AS POSSIBLE
RET
; DZHU2 -- ROUTINE TO DO A HANGUP
DZHU2: JE TTFEM,(T2),R ;RETURN IF NO DATASET
SAVET ;SAVE TEMP'S
CALL GETEXA ;GET EXTERNAL ADDRESS
BCIOB T1,DZLPR(T3) ;CLEAR LINE ENABLE
BCIOB T1,DZDTR(T3) ;CLEAR CARRIER
RET ;RETURN
;DZ7CX2 -- CARRIER ON
;DZCX2 -- CARRIER OFF
DZ7CX2: SKIPA T3,[TTCON1] ;CARRIER ON
DZCX2: MOVE T3,[TTCOF] ;CARRIER OFF
MOVEI T1,DZCRDL ;8 SEC
CALL TTQAD
RET
;DZCH7D -- PIA CHECK TO SEE IF INTERRUPTS ENABLES HAVE BEEN LOST
DZCH7D: MOVEI T1,SCDTMZ ;TIME FOR NEXT CHECK
MOVEM T1,TTYTIM ;TELL SCHEDULER
SOSLE DZCHCT ;TIME FOR PI CHECK?
JRST DZRING ;NO. DO RING POLL ONLY THEN
MOVEI T1,DZTMCK ;YES. SET UP NEXT TIME CHECK
MOVEM T1,DZCHCT ;AND SET UP "CLOCK"
CHNOFF DLSCHN ;TURN OFF DLS CHANNEL
MOVE T1,DZLNCT ;GET LINE COUNTS
JUMPE T1,DZCH7E ;IF NO DZ'S THEN NO CHECK
MOVE T2,[DZ11BA] ;GET BASE ADDRESS
MOVEI T3,DZRIEN!DZTIEN!DZMSCN
DZCH7L: TION T3,DZCSR(T2) ;CHECK FOR ENABLES
JRST [ BUG(DZLINT,<<T2,D>>)
MOVEI T4,377 ;SET ALL LINES TO INTERRUPT ASSUMING LOST ONE
WRIOB T4,DZTCR(T2)
BSIO T3,DZCSR(T2) ;SET INTERRUPT ENABLES AGAIN
JRST .+1]
ADDI T2,DZMNV ;LOOK AT NEXT DEVICE
SOJN T1,DZCH7L ;TRY NEXT ONE
DZCH7E: CHNON DLSCHN ;TURN ON CHANNEL
;NOW CHECK FOR RING ON ANY OF THE LINES
DZRING: SKIPE DZLNCT ;IF NO DZ LINES FORGET IT
SKIPGE T2,TT1LIN+TT.DZ ;GET FIRST LINE NUMBER
RET ;NONE THERE
MOVN T4,DZLNNO ;FIND COUNT OF LINES
HRL T2,T4 ;GET - NUMBER OF LINES
ADDI T2,FELNS ;UPDATE FOR CTY AND KLINIK
DZRNG0: JE TTFEM,(T2),DZRNG7 ;NOT A REMOTE LINE - NO PROCESSING NECESSARY
PUSH P,T2 ;SAVE ARGS
CALL GETEXA ;GET EXTERNAL PAGE ADDRESS
TIONB T1,DZRNG(T3) ;CHECK FOR RING
JRST NORNG ;NOT RING
JN TTCON,(T2),[SETZRO TTCON,(T2) ;HANG UP IMMEDIATELY
MOVEI T3,NTYCOF ;HANGUP ROUTINE
SETZ T1,0 ;DO ASAP
CALL TTQAD
JRST DZRRTN] ;IMPLIES NEW CALL
BSIOB T1,DZDTR(T3) ;SET CARRIER ON
JRST DZRSCO ;INDICATE CARRIER SET ON
DZRRTN: POP P,T2
DZRNG7: AOBJN T2,DZRNG0 ;DO THEM ALL
RET ;AND DONE
NORNG: TIONB T1,DZCAR(T3) ;CHECK FOR CARRIER ON
JRST CARNON ;CARRIER NOT ON
JN TTCON,(T2),DZRRTN ;CARRIER EXPECTED TO BE ON
DZRSCO: SETONE TTCON,(T2)
MOVE T3,[TTCON1] ;SET CARRIER ON
MOVEI T1,DZCRDL ;8 SEC
CALL TTQAD ;SCHEDULE IT
JRST DZRRTN ;AND QUIT
CARNON: JE TTCON,(T2),DZRRTN ;CARRIER NOT EXPECTED TO BE ON
CALL STADYN ;ACTIVE?
JRST DZCAR1 ;NOT ACTIVE AND QUIT BETTER KILL IT
JN TTPRM,(T2),DZRRTN ;NOT PERM --WAIT
DZCAR1: HRRZ 2,0(P) ;GET UNIT NUMBER BACK
SETZRO TTCON,(T2)
MOVE T3,[TTCOF] ;SET CARRIER OFF FLAG
MOVEI T1,DZCRDL ;8 SEC
CALL TTQAD ;SCHEDULE IT
JRST DZRRTN ;AND QUIT
;READ INTERRUPT ROUTINE
DZRDIN: MOVEM P,DZSAVP ;SAVE A REGISTER
MOVEI P,DZSVAC ;POINT TO AC SAVE AREA
BLT P,DZSVAC+16 ;SAVE AC'S
MOVE P,DZPDL ;SET UP STACK
MOVE Q1,DZLNCT ;FIND THE NUMBER OF LINES
MOVE Q2,[DZ11BA] ;FIND FIRST EXTERNAL PAGE ADDRESS
SKIPE FEFLG ;CHECK FOR PRIMARY PROTOCOL
JRST DZINPP ;YES -- GO DUMP ALL DZ'S
DZCTRD: RDIO T1,DZRBUF(Q2) ;READ A CHARACTER
TRNE T1,DZRDVL ;VALID?
JRST DZCTRD ;LOOP AND TRY FOR ANOTHER
DZNXCL: SOJE Q1,DZRXIT ;CHECK TO SEE IF ALL DZS DONE
ADDI Q2,DZMNV ;LOOK AT NEXT DZ TO DUMP ALL CHARACTERS
MOVEI T1,DZRDVL ;IN THE BUFFERS TO STOP THEIR INTERRUPTING
TIOE T1,DZRBUF(Q2) ;THIS WILL READ A CHARACTER AND DUMP IT
JRST .-1 ;THIS WILL CAUSE ALL CHARACTERS TO BE DUMPED
JRST DZNXCL ;GO DO NEXT DZ
DZINPP: MOVE P1,DZLNOF ;SET UP LINE NUMBER (MUST START AT 1
DZINPL: RDIO T1,DZRBUF(Q2) ;GET A CHARACTER
TRNN T1,DZRDVL ;VALID?
JRST DZNXLN ;NO -- GO TO NEXT LINE
TRNE T1,DZROVR ;OVER RUN
BUG(DZOVER,<<T1,D>>)
LOAD T2,DZTXLN,T1 ;GET THE LINE NUMBER
ADD T2,P1 ;FIND ITS INTERNAL LINE NUMBER
ANDI T1,377 ;MASK TO CHARACTER ONLY
CALL TTIDON ;GO PUT IN BUFFER
JRST DZINPL ;GET ANOTHER CHARACTER
DZNXLN: ADDI P1,10 ;8 LINES PER DZ
ADDI Q2,DZMNV ;LOOK AT NEXT DZ
SOJN Q1,DZINPL ;CHECK TO SEE IF COUNT DONE
JRST DZRXIT ;GO TO READ EXIT (DONE)
DZRXIT: MOVSI P,DZSVAC ;RESTORE ACS
BLT P,CX ;RESTORE
MOVE P,DZSAVP ;RESTORE P
XJEN DZRDIB ;RETURN
;INTERRUPT ROUTINE FOR THE CTY FOR THE KS10
DZCTIN::CLSB DLSCHN ;CLEAR CHANNEL INTERRUPT REQUEST
MOVEM P,DZSAVP ;SAVE STACK REGISTER
MOVEI P,DZSVAC ;POINT TO SC SAVE AREA
BLT P,DZSVAC+16 ;SAVE ACS
MOVE P,DZPDL ;SET UP STACK
JE KLIIVL,,DZNOKL ;CHECK FOR KLINIK INPUT
LOAD T1,KLIICH ;GET THE CHARACTER
MOVE T2,KLILNO ;GET LINE NUMBER
SETZRO KLIIVL ;CLEAR VALID BIT
CALL TTIDON ;OUTPUT CHARACTER
CALL INTETY ;INTERRUPT EIGHTY EIGHTY
DZNOKL: JN KLIOVL,,DZNXT ;OUTPUT VALID?
MOVE T2,KLILNO ;YES GET LINE NUMBER
CALL STADY ;GET DYN ADDR
JRST DZNXT ;TRY NEXT
CALL DZSND1 ;OUTPUT ANOTHER CHAR
DZNXT: JE CTYIVL,,DZNOCT ;CHECK FOR CTY INPUT
LOAD T1,CTYICH ;PICK UP THE CHACTER
MOVE T2,CTYLNO ;GET THE CTY LINE NUMBER
SETZRO CTYIVL ;CLEAR CHARACTER IN BUFFER FLAG
CALL TTIDON ;OUTPUT CHARACTER
CALL INTETY ;INTERRUPT EIGHTY EIGHTY
DZNOCT: JN CTYOVL,,DZNXIT ;NO CTY
MOVE T2,CTYLNO ;GET LINE NUMBER
CALL STADY ;CONVERT TO DYNAMIC STORAGE
JRST DZNXIT ;QUIT IF NO DYNAMIC STORAGE
CALL DZSND1
DZNXIT: MOVSI P,DZSVAC ;RESTORE
BLT P,CX
MOVE P,DZSAVP
RET ;RETURN
DZPDL: IOWD 40,DZISTK ;I/O STACK SIZE
RS (DZISTK,40) ;STACK FOR INTERRUPT SERVICE
RS (DZRDIB,4) ;INPUT INTERRUPT BLOCK
RS (DZXINB,4*^D8) ;INTERRUPT BLOCK FOR OUTPUT
RS (DZSVAC,17) ;SAVE AC FOR READ INTERRUPT
RS (DZSAVP,1) ;SAVE AC 17
RS (DZLNCT,1) ;COUNT OF DZ'S FOUND
RS (DZLNNO,1) ;COUNT OF LINES FOUND
RS (DZLNOF,1) ;OFFSET TO FIRST LINE NUMBER
; NOTE MUST HAVE ONE SET OF 3 INSTRUCTIONS PER DZ11!!!!!!
DZTXIN::DMOVEM P6,DZSVAC+P6 ;SAVE REGISTERS
SETZ P6,0 ;POINTER TO WHICH LINE SET
JRST DZCOMI ;GO TO COMMON INTERRUPT SERVICE
DZTXI1: DMOVEM P6,DZSVAC+P6
MOVEI P6,10 ;SECOND BLOCK OF 10
JRST DZCOMI
DZTXI2: DMOVEM P6,DZSVAC+P6
MOVEI P6,20
JRST DZCOMI
DZTXI3: DMOVEM P6,DZSVAC+P6
MOVEI P6,30
JRST DZCOMI
DZTXI4: DMOVEM P6,DZSVAC+P6
MOVEI P6,40
JRST DZCOMI
DZTXI5: DMOVEM P6,DZSVAC+P6
MOVEI P6,50
JRST DZCOMI
DZTXI6: DMOVEM P6,DZSVAC+P6
MOVEI P6,60
JRST DZCOMI
DZTXI7: DMOVEM P6,DZSVAC+P6
MOVEI P6,70
; JRST DZCOMI
; ..
; ..
DZCOMI: MOVEM P,DZSAVP ;SAVE A REGISTER
DMOVEM T1,DZSVAC+T1
DMOVEM T3,DZSVAC+T3
DMOVEM Q1,DZSVAC+Q1
MOVE P,DZPDL ;SET UP STACK SIZE
MOVE Q2,[DZ11BA] ;GET BASE ADDRESS
ADD Q2,P6 ;POINT TO CORRECT ADDRESS
LSH P6,-1 ;FIND RETURN ADDRESS
DMOVE T1,DZXINB(P6) ;GET RETURN PS/PC
DMOVEM T1,DZXINB ;STORE IN COMMON RETURN
LSH P6,1 ;GET ADDRESS BACK
ADD P6,DZLNOF ;SET UP LINE COUNT
DZTNXO: RDIO T2,DZCSR(Q2) ;READ THE STATUS
TRNN T2,DZTRDY ;CHECK FOR TRANSMIT DONN
JRST DZTXIT ;NOT THIS DZ TRY NEXT ONE
LDB T2,[POINT 3,T2,27] ;PICK UP LINE NUMBER
MOVNS T2 ;GET CORRECT BIT POSITION
MOVE Q1,BITS+^D35(T2) ;SAVE LINE NUMBER
MOVNS T2 ;BACK THE WAY IT WAS
ADD T2,P6 ;MAKE ABSOLUTE NUMBER
JN <TTXOC>,(T2),[
CALL GETEXA
CALL DZXOCA ;DO XON/XOF
JRST DZTNXO]
SKIPN T2,TTACTL(T2) ;NET DYNAMIC STORANE
JRST DXTNEX ;IF NO BLOCK THIS IS AN EXTRNAEOUS INTERRUPT
CALL TTSND ;DO TTY DONE
JRST DXTNEX ;BFR EMPTY
SETONE TTOTP,(T2) ;SET OUTPUT ACTIVE
WRIOB T1,DZTBUF(Q2)
JRST DZTNXO
DXTNEX: BCIOB Q1,DZTCR(Q2) ;CLEAR THE ACTIVE BITS
JRST DZTNXO ;TRY FOR ANOTHER
;THIS WILL STOP INTERRUPTING DZ AND END OUTPUT
DZTXIT: DMOVE T1,DZSVAC+T1
DMOVE T3,DZSVAC+T3
DMOVE Q1,DZSVAC+Q1
DMOVE P6,DZSVAC+P6
MOVE P,DZSAVP ;RESTORE AC
XJEN DZXINB ;AND RETURN
;SEND XON/XOFF
DZXOCA: JN TTFXO,(T2),DZDZXF ;XOFF?
DZDZXO: MOVEI T4,XONC ;GET CHARACTER
SKIPA ;COMMON ENTRY
DZDZXF: MOVEI T4,XOFFC ;GET XOFF CHARACTER
SKIPGE CHITAB(T4) ;PARITY NEEDED?
TXO T4,200 ;YES, APPLY IT
SETZRO <TTXOC>,(T2) ;CLEAR FLAGS
WRIOB T4,DZTBUF(T3) ;WRITE CHARACTER
RET
; SENDALL
SWAPCD
DZSNDL: SKIPN FEFLG ;PRIMARY PROTOCOL?
JRST [ SETO T2, ;NO, RETURN SKIP GROUP
RETSKP]
CAME T2,KLILNO
CAMN T2,CTYINT ;CHECK FOR REAL CTY
RET ;CAN'T DO THIS LINE
SKIPGE TTSPWD(T2) ;SPEED SET?
RET ;NO, SKIP LINE
PUSH P,T2
SUB T2,DZLNOF ;FIND IF LINE A LEGAL DZ LINE
CAML T2,DZLNNO ;LGAL? (DZ'S +CTY)
JRST [ ADD T2,DZLNOF ;PUT LINE NUMBER BACK
CAME T2,KLILNO ;CHECK FOR KLINIK
CAMN T2,CTYLNO ;CHECK FOR CTY
JRST .+1 ;YUP ALL OK TO DO SENDALL
JRST PB2] ;NOPE QUIT
DZCTOK: POP P,T2 ;RESTORE LINE NUMBER
RETSKP
; SET SPEED FOR A DZ11 LINE
DZSSP2: UMOVE T4,2 ;GET FLAGS
TXNE T4,MO%AUT ;REQUESTING AUTO?
RETBAD ;YES. CAN'T HAVE IT ON THIS DEVICE
SKIPN DZLNCT ;IF NO DZ LINES CAN'T SET SPEED
RET
UMOVE T4,T3 ;GET THE SPEED
HLRZ T1,T4 ;CHECK TO SEE BOTH HALF THE SAME
CAME T2,KLILNO ;NOT KLINIK LINE NUMBER EITHER
CAMN T2,CTYINT ;CHECK FOR CTY
RET ;NOT LEGAL ON THIS MACHINE
CAME T2,CTYLNO ;CHECK TO SEE IF CTY (CAN'T SET THAT ONE)
CAIE T1,0(T4) ;IF NOT SAME THEN FORGET IT HARDWARE
RET ;SUPPORTS INPUT/OUTPUT SAME
NOINT ;SET NOINT
CHNOFF DLSCHN ;TURN OFF CHANNEL WHILE PLAYING WITH LINE SPEEDS
JN TTFEM,(T2),DZSSP1 ;IF REMOTE DON'T SET PERM SPEED
XCTU [SKIPGE 2] ;REMOTE REQUESTED?
JRST [ MOVX T3,SC%OPR!SC%WHL ;CHECK CAPBILITIES
TDNN T3,CAPENB
JRST DZSSP1 ;NO CAPABILITIES FORGET IT
SETONE TTFEM,(T2) ;SET ONCE ONLY FLAG
JRST .+1]
JUMPE T4,[EXCH T4,TTSPWD(T2) ;TREAT SPEED ZERO SPECIALLY, PRESERVE
JRST DZSSP1] ; OUTPUT CHARACTERISTICS, TURN OFF INPUT
MOVEM T4,TTSPWD(T2) ;SAVE TTY SPEED
DZSSP1: HRRZS T4 ;SET SPEED IN RIGHT HALF ONLY
MOVEI T1,DZSPTB ;FIND POINTER TO TABLE POINTER
DZSPLP: MOVE T3,0(T1) ;GET A TABLE ENTRY
JUMPE T3,NOLNSP ;NO LINE SPEED FOUND
CAIE T4,0(T3) ;CORRECT ENTRY?
AOJA T1,DZSPLP ;NO -- TRY NEXT ONE
HLRZ T4,T3 ;GET LINE SPEED
MOVE T3,T2 ;GET LINE NUMBER
SUB T3,DZLNOF ;SUBTRACT FRONT-END LINES
CAML T3,DZLNNO ;CHECK TO SEE IF LEGAL LINE NUMBER
JRST NOLNSP ;NOPE -- QUIT WHILE AHEAD
ANDI T3,7 ;MASK TO 3 BITS
IOR T4,T3 ;SET UNIT NUMBER
CALL GETEXA ;GET THE EXTERNAL PAGE ADDRESS OF THIS DZ
SKIPN TTSPWD(T2) ;SETTING SPEED TO ZERO?
TRZ T4,DZ1RXO ;YES, FOR DZ HARDWARE TURN OFF RX CLOCK
WRIO T4,DZLPR(T3) ;SET THE LINE PARAMETER REGISTER
NOLNSP: CHNON DLSCHN ;ENABLE CHANNEL
OKINT ;ENABLE INTERRUPTS
RET ;RETURN
DZSPTB: DZ1RXO+DZ1OPA+DZ8BIT+DZ2STP+0,,^D50
DZ1RXO+DZ1OPA+DZ8BIT+DZ2STP+400,,^D75
DZ1RXO+DZ1OPA+DZ8BIT+DZ2STP+1000,,^D110
DZ1RXO+DZ1OPA+DZ8BIT+DZ1STP+1400,,^D134
DZ1RXO+DZ1OPA+DZ8BIT+DZ1STP+2000,,^D150
DZ1RXO+DZ1OPA+DZ8BIT+DZ1STP+2400,,^D300
DZ1RXO+DZ1OPA+DZ8BIT+DZ1STP+3000,,^D600
DZ1RXO+DZ1OPA+DZ8BIT+DZ1STP+3400,,^D1200
DZ1RXO+DZ1OPA+DZ8BIT+DZ1STP+4000,,^D1800
DZ1RXO+DZ1OPA+DZ8BIT+DZ1STP+4400,,^D2000
DZ1RXO+DZ1OPA+DZ8BIT+DZ1STP+5000,,^D2400
DZ1RXO+DZ1OPA+DZ8BIT+DZ1STP+5400,,^D3600
DZ1RXO+DZ1OPA+DZ8BIT+DZ1STP+6000,,^D4800
DZ1RXO+DZ1OPA+DZ8BIT+DZ1STP+6400,,^D7200
DZ1RXO+DZ1OPA+DZ8BIT+DZ1STP+7000,,^D9600
0,,0 ;END OF TABLE
RESCD
;GETEXA -- SUBROUTINE TO FIND THE EXTERNAL PAGE ADDRESS OF
; THE SPECIFIED DZ11
; CALLING SEQUENCE:
; T2 -- LINE NUMBER
;
; CALL GETLIN
; T1 -- LINE BIT POSITION (LINE 0=1B35 ETC)
; T3 -- EXTERNAL PAGE ADDRESS OF FIRST REGISTER FOR THIS DZ11
; RETURNS +1 ALWAYS
GETEXA: PUSH P,T2 ;SAVE LINE NUMBER
GETEX1: SUB T2,DZLNOF ;BACKUP TO POINT TO REAL NUMBER
MOVE 3,2 ;GET LINE NUMBER
ANDI T3,777770 ;MASK OF LOW ORDER 3 BITS (8 PER DZ)
ADD T3,[DZ11BA] ;ADD DZ11 BASE ADDRESS
MOVE T1,T2
ANDI T1,7 ;MASK OFF UNIT
MOVNS T1
MOVE T1,BITS+^D35(T1)
POP P,T2 ;RESTORE
RET
;
; GETEXL -- SUBROUTINE TO FIND EXTERNAL PAGE AND LINE NUMBER
;
; CALLING SEQUENCE:
; B -- DYNAMIC STORAGE ADDRESS
; CALL GETEXL
; RETURNS:
; A -- LINE BIT POSITION (LINE 0=1B35 1,1B34 ETC)
; C -- EXTERNAL PAGE ADDRESS OF THIS DZ11
;
GETEXL: PUSH P,T2 ;SAVE DYNAMIC ADDRESS
DYNST ;GET LINE NUMBER
CALLRET GETEX1 ;GET EXTERNAL PAGE ADDRESS
> ;END IFN .DZFLG MANY PAGES BACK
IFE .DZFLG,<
;DUMMY SYMBOLS
DZHU2:
>
;END OF ALL TTYSRV MODULES
TNXEND
END