PDP-10 Archive: 2-exercise-libary/diagno.log from DEC-20-OT20A-D-MC9

Trailing-Edge - PDP-10 Archives - DEC-20-OT20A-D-MC9 - 2-exercise-libary/diagno.log
There are no other files named diagno.log in the archive.
10:00:16 BAJOB	BATCON version 101(2014) running DIAGNO sequence 74 in stream 1
10:00:16 BAFIL	Input from DSK:<1COHEN>DIAGNO.BAT
10:00:16 BAFIL	Output to  DSK:<1COHEN>DIAGNO.LOG
10:00:16 BASUM	Job parameters
		Time:00:00:45   Unique:YES   Restart:NO   Output:NOLOG

10:00:16 MONTR	
10:00:17 MONTR	 V 1.02.39, 1031 Development Sys., 22-APR-76. TOPS-20 1A(110)
10:00:17 MONTR	@LOGIN COHEN 10300
10:00:17 MONTR	  JOB 20 ON TTY110 23-APR-76 10:00
10:00:19 MONTR	@
10:00:19 MONTR	[CONNECTED TO 1COHEN]
10:00:19 MONTR	@SET TIME-LIMIT 45
10:00:20 MONTR	@
		!DIAGNO.BAT
		!
		!THIS BATCH CONTROL FILE RUNS IN THE DIRECTORY <DIAGNOSTICS>,
		! WHICH SHOULD CONTAIN VARIOUS PROGRAMS AND FILES NEEDED
		! TO RUN USER-MODE DIAGNOSTICS.  IN PARTICULAR:
		!
		!	DIAMON.SAV	CONTROL PROGRAM WHICH STEPS THROUGH
		!			ANY NUMBER OF DIAGNOSTIC PROGRAMS
		!			ANY NUMBER OF TIMES, DEPENDING ON THE
		!			CONTENTS OF THE FILE KLUSR.CMD
		!
		!	KLUSR.CMD	CONTROLS THE RUNNING OF DIAGNOSTIC PROGRAMS
		!
		!	SUBRTN.A10
		!
		!	KLDDT.A10
		!
		!	DFKAA.A10
		!	DFKAB.A10
		!	DFKAC.A10
		!	DFKAD.A10
		!	DFKBA.A10
		!	DFKCA.A10
		!	DFKDA.A10
		!	
		!THE FOLLOWING COMMANDS RUN DIAMON ONCE, AND ASSURE THAT
		! ERRORS REPORTED BY THE DIAGNOSTICS WILL NOT CAUSE THE BATCH
		! JOB TO TERMINATE.  THE EXPECTED CONTENTS OF KLUSR CAUSES
		! DIAMON TO CYCLE THROUGH THE PRESCRIBED DIAGNOSTIC PROGRAMS
		! INDEFINATELY,  SO THAT ACTUAL TERMINATION OF THE JOB ONLY
		! OCCURS WITH A TIME-OUT.  NOTE THAT THIS JOB IS NORMALLY
		! SUBMITTED WITH A TIME-LIMIT OF 3 MINUTES OR 10-HOURS.
		! THESE TIME LIMITS ARE EQUIVALENT TO "MEDIUM LENGTH RUN"
		! AND "VERY LONG RUN".
		!
		!
10:00:20 BATCH	@NOERROR
10:00:20 MONTR	@RUN DIAMON.SAV
10:00:22 USER	
10:00:22 USER	* DIAMON [DDQDC] - DIAGNOSTIC USER & EXEC MONITOR VER 0.10 *
10:00:22 USER	HELP ? - 
		!WE DON'T WANT HELP
10:00:22 USER	*N
10:00:23 USER	
10:00:23 USER	DIAMON CMD - 
		!THE SOURCE DEVICE FOR THE FILE TO BE NAMED IS "DISK".
10:00:23 USER	*D
10:00:24 USER	
10:00:24 USER	FILE.EXT - 
		!THE COMMAND FILE IS KLUSR.CM