Trailing-Edge
-
PDP-10 Archives
-
bb-bt99e-bb
-
readme.011
There are no other files named readme.011 in the archive.
1.0 INTRODUCTION
This is the eleventh Autopatch set. It contains patches for
ALGOL-10-V1-2, ANF10-V23, APL-10-V2, APLSF-10-V2, COBOL-10-V12B,
DECNET-10-UTILITIES-V702, FORTRAN-10-V10, GALAXY-10-V702,
IBMCOM-10-ET-V4, IBMCOM-10-HASP-V1, LINK-10-V5-1, MCB-10-V702,
SORT-10-V4C, TOPS-10-KL-V702, TOPS-10-KS-V702, and UTILITIES-10-V702.
To install Autopatch for the first time, you must first restore the
second save set and follow the instructions found in the Autopatch
Procedures/Reference Manual and the INSTAL.DOC file. Information
specific to each product is recorded in section 5.0 of this document.
2.0 EXCEPTIONS
1. The following product(s) are no longer Autopatched because of
new releases: FORTRAN-10-V6, FORTRAN-10-V7, GALAXY-10-V4-1,
NFT-10-V1, TOPS-10-DN6X-V701A, TOPS-10-KI-V701A,
TOPS-10-KL-V701A, TOPS-10-KS-V701A, TOPS-10-MPE-V701A,
TOPS-10-TSK-V701, and UTILITIES-10-V701A.
*NOTE* It is strongly suggested that you DESELECT any of these
products before proceeding with processing any currently
supported products.
2. The following Autopatched product(s) do not have any new edits
delivered with this patch set: ALGOL-10-V10B, APL-10-V2,
APLSF-10-V2, DBMS-10-V5A, DECNET-10-UTILITIES-V702,
IBMCOM-10-ET-V4, IBMCOM-10-HASP-V1, MS-10-V10, RMS-10-V1, and
TOPS-10-MPE-V702.
3. (*new*) The Autopatch build for source-patched products will
delete source files in PAT: to prevent problems if a build is
re-started. This process may fail if PAT: is defined with
SFDs. Either do not use SFDs when defining PAT: or manually
delete the source files in the SFD before re-starting the
Autopatch build.
4. (*new*) The TOPS-10-KL and TOPS-10-KS product builds will fail
unless they can find a JOBDAT.REL file in SYS:. In fact, this
file is not used but a lookup does occur.
5. (*new*) If you are using the new FORTRAN-10 V10 with DBMS you
will need a revised DBCS1F.CMD file from the second save-set on
the Autopatch tape. This file should be copied into the
FORTRAN distribution area. The copy of this file which was
distributed with DBMS V5A must be removed or the FORTRAN build
will fail.
6. (*new*) A revised copy of TGHA.EXE is contained in the first
save-set on this tape. This copy is required for use of the
new MG20 memory.
Page 2
7. (tape 10) If you are using DBMS with FORTRAN or COBOL, do not
INSTALL DBMS with PEP until FORTRAN and/or COBOL has been
built. A feature of PEP which was new with tape 9 deletes the
autopatched files from PAT: upon successful instalation. The
COBOL and FORTRAN products depend on the necessary DBMS files
being in PAT:.
8. (tape 10) There are new batch control files for
TOPS-10-DCN-V702 and TOPS-10-MPE-V702 in the installation
(second) save-set. They have been modified to 'leave' the
correct support files for the monitor build in PAT: when the
products are autopatched and no edits have been delivered.
These files are restored to PAT: by the product BACKUP command
files.
9. (tape 10) There are three .REL modules for DBMS (FML10, INF10
and MND10) which are nul. This causes a %CGV error message at
the end of the batch job and when PEP is checking the results
of the batch job. These messages should be ignored.
10. (tape 10) There are eight Patch Command Files on this save-set.
They are APL1B2.MKL, APL1S2.MKL, DBMV5A.MKL, DNU702.SUP,
IETV04.SUP, IHSV01.SUP, MPE702.SUP, and RMS1V1.MKL. These
products have no patches on this tape. Without these files, if
you were to 'AUTOPATCH' the products with PEP and SUBmit the
patch and build control files the process would use old
patching indirect command files. This would cause a failure
with DBMS and unnecessary processing with RMS. The 'null'
patching indirect command files will avoid this problem. Any
checksum warnings regarding these files may be ignored.
11. (tape 9) KS10 systems may have a problem with PFH effectively
hanging. The problem can be avoided by using the /CORE switch
to the SUBMIT command to specify a page limit which is 300
pages or greater.
12. (tape 9) The DECNET-10-UTILITIES-V702 product obsoletes the
NFT-10-V1 Autopatch product. All edits previously delivered to
NFT are included in the new product. DECNET customers who have
previously Autopatched NFT should use the RESTORE NFT-10-V1
command and the DESELECT NFT-10-V1 command to PEP. These
customers should then use the DNU702.CCL file to load the
distribution area.
Customers who are Autopatching DECNET for the first time should
use the DCN702.CCL file which also loads monitor modules for
DECNET. All DECNET customers should then install
DECNET-10-UTILITIES for Autopatching.
13. (tape 9) Patch files for four Utilities were improperly
delivered on tape 8. None of the files were referenced in the
Distributed Patch Directory file (PAT108.DPD) and therefore had
no effect via Autopatch. The CREF.C08 and INITIA.C08 files
were, in effect, empty. The DIRECT.C08 file had a bad edit,
and the COMPIL.C08 file had good edits but they were not
Page 3
applied. You will have problems with Autopatch ONLY if you
applied either the DIRECT or COMPIL edits manually, outside of
the Autopatch process. The COMPIL edits are applied via
Autopatch as a part of tape 9.
14. (tape 9) The ANF10 product is NOT rebuilt by Autopatch. The
Autopatch process will update the supported sources in the DIS:
area. After the INSTALL command has been processed, the
customer may use the sources in DIS: to rebuild the product
with procedures which are appropriate for your site.
15. (tape 9) A new MS1V10.CTL file is provided in the second
save-set. The change was made so that it would not fail even
if used when no patches are provided.
16. (tape 9) There are two new features of PEP and PEPB which are
worthy of note. First, the new PEP will automatically delete
copies of files in PAT: which have been successfully installed
with the INSTALL command.
Second, the definition of ASL: has been changed to be
PAT:,DIS:,INS:. The old definition was
PAT:,DIS:,REL:,UNV:,SYS:. This change was made to obtain
better control over all files used in the build process. We
have delivered what we believe to be a complete set of base
building software on the Autopatch tape. If your procedure has
problems you may have to copy certain files into PAT:, DIS:, or
INS:.
The following files are required for Autopatch use, not put in
place by Autopatch, and may have been previously found in SYS:.
IBMCOM HASP and ET
DDT11.EXE GALCNF.UNV MACDLX.EXE
FORTRAN
BLIS10.EXE BLIS10.ERR
RMS
RMSINI.REL
TOPS-10 KL
FKL.MAC HDWKL.MAC TTYKL.MAC NETKL.MAC
TOPS-10 KS
FKS.MAC HDWKS.MAC TTYKS.MAC NETKS.MAC
If these files are currently found in SYS: they must be copied
or moved to PAT:, DIS:, or INS:.
Page 4
The SORT product currently looks for FTDEFS.UNV amd METUNV.UNV
in ASL:. In fact the SORT build does NOT use these files.
This will be fixed on a future Autopatch tape. Since SYS: is
no longer in the ASL: definition, you may have to copy these
files from SYS:. Users who Autopatch SORT for the first time
and users who have these files in PAT: from a previous COBOL
build will not have this problem.
17. (tape 9) If you Autopatch both COBOL and GALAXY, build Galaxy
before COBOL, but INSTALL COBOL before GALAXY, you will get a
checksum warning and the 'wrong' CHREQV.UNV file in INS:.
The CHREQV.UNV file is not, in fact, needed any longer by
GALAXY. Unless you depend on GALAXY's CHREQV.UNV file being in
INS: for other reasons, this problem should be ignored.
First-time users of Autopatch on GALAXY will not experience the
error.
18. (tape 9) The IBMCOM products have a module named MACROS.P11
which conflicts with a module by the same name with different
contents in the ANF10 product. The IBMCOM MACROS module has
been renamed as MACRO.P11. For users of Autopatch on the
IBMCOM products for the first time, if the IETV04 or IHSV01
.CCL file is used to load the distribution directory then no
action is required by the user. Otherwise, the distributed
MACROS.P11 file must be renamed to be MACRO.P11 or the
MACRO.P11 file on the Autopatch tape must be put in DIS:. The
UTILTY.UPD file will update the Patch Database file.
Also note that IBMCOM products use some galaxy supported files.
Be sure that the GALAXY product has been Autopatched through
the control file phase before Autopatching IBMCOM products.
19. (tape 8) The monitor, CUSPS and GALAXY components supported by
this tape are all based on the products as delivered with the
TOPS-10 V7.02 release. It is suggested that all DIS:
distribution directories for the previous versions be cleared
or moved elsewhere before installing the new versions for
Autopatching. The supplied updates will not apply to the
V7.01A components including GALAXY-10-V4-1. LINK and RMS
remain unchanged from the V7.01A release to the V7.02 release
and, therefore, do NOT need to be re-installed.
20. (tape 8) The CCL files in the second save set of this tape are
designed to aid the process of loading the DIS: directories
from the product distribution tapes. The CSP702.CCL permits
'one pass' of the CUSP to load all files needed for
UTILITIES-10-V702, GALAXY-10-V702, and TOPS-10-K?-V702. Use of
the GAL702.CCL or UTL702.CCL files is appropriate only if you
do not use the CSP702.CCL file. The monitor products also
require files from the CUSSUP tape. The CSC702.CCL file will
accomplish this task. The DCN702.CCL file will load monitor
modules and the DECNET utility files.
Page 5
21. (tape 8) Edit 3316 to FORTRAN-10-V7 was not delivered properly
on tape 7. The MTHCDX portion was missing. The missing piece
of edit 3316 is delivered on this tape and will be applied as a
part of the normal Autopatch process.
22. (tape 8) Labelled tapes written through the services of PULSAR
may not be compatible with the previous version of PULSAR. See
the GAL702.B08 file.
23. (tape 8) The TOPS-10-MPE-V702 and TOPS-10-DCN-V702 products do
not require a build procedure. There are no 'output' files,
only updated source files. The LOG files for these products
will show messages relating to zero checksums and the inability
to get version numbers. These messages may be ignored.
24. (tape 8) The COBOL, LINK and SORT LOG files will show a
warnings about three obsolete references (.SGNAM, .SGPPN and
.SGDEV). These will be changed at a later time. The warnings
may be ignored.
25. (tape 7) Changes have been made to the PEP utility. It is
MANDATORY that PEP.EXE and PEPB.EXE be restored to SYS: from
the installation (second) save-set.
Due to a limited amount of space in some of PEP's internal
tables, we are now declaring some products to be "obsolete".
These products will be removed from PEP's internal tables. For
the most part this process is transparent to you, unless the
obsolete product has previously been SELECTed. Suppose
FORTRAN-10-V6 is one of your SELECTed products. In that case,
the following message would be displayed the first time you run
the new PEP:
[FORTRAN-10-V6 is now obsolete.
Edits are no longer being delivered.
You should DESELECT this product.]
This message will only appear ONCE PER SELECTED OBSOLETE
PRODUCT. Use the DESELECT command to purge the obsolete
product from your database.
NOTE
The PEP101.PDF file is NOT compatible with earlier
versions of PEP.
There is now a short version of the INFORMATION command called
STATUS. It displays the status information and logical name
definitions, but does not list any files or their checksums.
For example, you might see the following:
PEP>status LINK-10-V5-1
Page 6
LINK-10-V5-1 is ready to be SETUP for patch and rebuild
Patches retrieved through patch tape 7
Logical names:
PAT: (autopatching directory) defined as DSKP:[7,6]
DIS: (distribution directory) defined as DSKP:[7,6,LINK]
BAK: (backup directory) defined as DSKP:[7,6,BACKUP]
INS: (installation directory) defined as SYS:
ASL: (autopatch search list) defined as PAT:,DIS:,SYS:
26. (tape 7) Edit 1742 to FORTRAN-10-V7 was not delivered properly
on tape 6. The DOALC portion was missing and may have caused
problems using DO-LOOP indices as character subscripts in I/O
keywords. The missing piece of edit 1742 is delivered on this
tape and will be applied as a part of the normal Autopatch
process.
27. (tape 7) There was an error in the PDF file used to autopatch
COBOL. Not all of the .EXE files resulting from a build will
be installed in the correct area. The PDF file is correct for
ONESEG compilers only. Setting the ONESEG switch on in the
COBASM file will cause a single-segment compiler to be built.
A change was made to the PEP delivered on tape 6 which asks if
the compiler is multi-segemented when COBOL is SELECTed for
autopatching. However, the modified PDF file was NOT present
on tape 6.
As a result of this error, the autopatch procedure will end
normally, but will not have copied all of the newly built .EXE
files into the correct installation area. This means the user
will have to copy them in manually. These modules are:
68274
ANSI 68 ANSI 74 CONVERTER
COBOLC.EXE CBL74C.EXE 68274C.EXE
COBOLD.EXE CBL74D.EXE 68274D.EXE
COBOLE.EXE CBL74E.EXE 68274E.EXE
COBOLO.EXE CBL74O.EXE
COBOLK.EXE CBL74K.EXE 68274K.EXE
COBOLF.EXE CBL74F.EXE 68274F.EXE
The correct PDF file is on this tape (7), so that new users
will not have this problem. To implement the new CBL12B.PDF
for users have have already autopatched COBOL and are not using
ONESEG compilers requires that the product be DESELECTed and
SELECTed with PEP. This also requires that original sources
from the COBOL release tape be re-loaded into the DIS: area.
The Autopatch process will then completely and correctly update
the product in one 'pass' through the process.
28. (tape 7) Errors have been corrected in the CBL12B.CTL file.
This file must be restored to the common patching area from the
second save-set. This operation is included in the supplied
Page 7
appropriate BACKUP indirect command file for processing the
Autopatch tape.
29. (tape 7) Edit 612 to DBMS-10-V5A eliminates the need for the
DBSINF.REL module which was introduced on Autopatch tape 5.
Users who have Autopatched DBMS previously are urged to be sure
that the new version of the DBINF1.CMD file is restored from
the patch set 7 save set on this tape. Use of the DBMV5A.Ann
file will accomplish this task.
30. (tape 7) The second chapter of the TOPS-10/TOPS-20 Autopatch
Procedures/Reference Manual suggests a quota of 20,000 blocks
for the [7,6] PPN on page 2-2. Because of additional product
support, it is now suggested that you use a figure of 140000.
31. (tape 6) The patch directory files (.DPD) have been
re-formatted; the same number of edits, but less 'patches',
are described. Also, intermediate checkpointing has been
suppressed during the execution of the PEP 'AUTOPATCH' command.
Checkpoint processing time has been SIGNIFICANTLY reduced.
These changes will improve PEP performance, but will cause
minor variations from the examples provided on pages 2-7, 2-17
and 3-8 of the Autopatch Procedures/Reference Manual.
32. (tape 6) Users of FORTRAN with DBMS MUST create a file - read
the INSTAL.DOC file.
If you have previously SELECTed DBMS for Autopatch and
indicated that FORTRAN was being used than you may want to 're
do' DBMS. FORTRAN V6 is no longer supported by Autopatch.
With FORTRAN V7 the FORLIB.REL file is not modified for DBMS
and the DBMSF.EXE file is autopatched by FORTRAN.
The suggested procedure is to use the DBMV5A.Ann file to
restore all files for DBMS from this tape and issue the
DESELECT and SELECT commands for DBMS-10-V5A to PEP before
Autopatching DBMS. Otherwise, the DBMS Autopatch process will
'install' copies of FORLIB.REL and DBMSF.EXE which is also done
by the FORTRAN Autopatch process.
33. (tape 6) There are three warning messages seen during the
patching of REL libraries of the DBMS product. Newer edits are
trying to remove edits which were suppressed. This condition
is non-fatal and has no impact on the success of DBMS updating.
Ignore the messages.
34. (tape 6) BATCH time limits for FORTRAN and COBOL should be high
to ensure that the product build BATCH jobs do not abort due to
CPU time overrun. Use a figure of 5 hours to cover all
possibilities.
35. (tape 6) Some products can optionally use other products. This
means that one product may have to be patched and rebuilt
before another product. For example, COBOL can optionally use
the DBMS product. The COBOL Autopatch process requires that
Page 8
DBMS and SORT be updated before COBOL. In order to apply all
patches correctly you must SUBMIT the Patch and Build Control
file for SORT and DBMS before the COBOL Control file. The MPE
and DCN options to the TOPS-10 Monitor must be Autopatched
before the Control file to build the monitor is submitted.
36. (tape 5) Before selecting the ALGOL product for Autopatching be
sure to read the note in the INSTAL.DOC file regarding a
required rename of the OTS.
37. (tape 4) When PEP is run, the default directory must be PAT:.
38. (tape 4) It is advised that all desired products be SELECTed
for Autopatching before entering the AUTOPATCH or RETRIEVE
command for the first time. The patch retrieval process is NOT
product specific. This process can be invoked with the
RETRIEVE command or the AUTOPATCH command. PEP will then read
the entire patch directory file (.DPD) and update the patch
database file (.PDB) for all SELECTed products. If the
AUTOPATCH command is entered for a product which was SELECTed
at the time of a prior retrieval process, a statement will be
made indicating that all patches have already been retrieved.
3.0 RELATED DOCUMENTS
TOPS-10/TOPS-20 Autopatch Procedures/Reference Manual (AA-H729A-TK)
INSTAL.DOC (in Installation Save Set on this tape)
4.0 FILE INDEX
Patch Set 011
File Description
README.011 Patch Set 011 Master Documentation File
TAP011.DIR Directory with Checksums of Patch Set 011
PAT111.DPD Patch Directory File for Patch Set 011
ALG10B.SUP Null Patch Command Files
APL1B2.MKL
APL1S2.MKL
DBMV5A.MKL
DNU702.SUP
IETV04.SUP
IHSV01.SUP
MPE702.SUP
RMS1V1.MKL
APEDIT.RPT Autopatch Edit Report
UTILTY.UPD Utility checksum and version update file
Page 9
Edit Description Files
ANFV23.D11 ANF10-V23 Edit Description File
CBL12B.D11 COBOL-10-V12B Edit Description File
DCN702.D11 TOPS-10-DCN-V702 Edit Description File
FTN10.D11 FORTRAN-10-V10 Edit Description File
GAL702.D11 GALAXY-10-V702 Edit Description File
LNKV51.D11 LINK-10-V5-1 Edit Description File
MCB702.D11 MCB-10-V702 Edit Description File
SRTV4C.D11 SORT-10-V4C Edit Description File
T1L702.D11 TOPS-10-KL-V702 Edit Description File
T1S702.D11 TOPS-10-KS-V702 Edit Description File
UTL702.D11 UTILITIES-10-V702 Edit Description File
Patch Files
DNCNFG.C11 DNCNFG.P11 Patch File ANF10-V23
COBDDT.C11 COBDDT.MAC Patch File COBOL-10-V12B
COBOLB.C11 COBOLB.MAC Patch File
COBOLD.C11 COBOLD.MAC Patch File
COBST.C11 COBST .MAC Patch File
COBVER.C11 COBVER.MAC Patch File
LSU.C11 LSU .MAC Patch File
ACT1.C11 ACT1 .BLI Patch File FORTRAN-10-V10
EXPRES.C11 EXPRES.BLI Patch File
FIRST.C11 FIRST .BLI Patch File
FORDDT.C11 FORDDT.MAC Patch File
FORHST.C11 FORHST.MAC Patch File
FORIO.C11 FORIO .MAC Patch File
FORMAT.C11 FORMAT.BLI Patch File
FORMSG.C11 FORMSG.MAC Patch File
FOROPN.C11 FOROPN.MAC Patch File
REVHST.C11 REVHST.MAC Patch File
STA0.C11 STA0 .BLI Patch File
STA2.C11 STA2 .BLI Patch File
Page 10
DORTB.X11 DORTB .EXE Patch File FORTRAN-REP-V10
DORTC.X11 DORTC .EXE Patch File
DORTD.X11 DORTD .EXE Patch File
DORTE.X11 DORTE .EXE Patch File
DORTF.X11 DORTF .EXE Patch File
DORTG.X11 DORTG .EXE Patch File
DORTRA.X11 DORTRA.EXE Patch File
FORDDT.X11 FORDDT.REL Patch File
FORLIB.X11 FORLIB.REL Patch File
FORO10.X11 FORO10.EXE Patch File
FORTB.X11 FORTB .EXE Patch File
FORTC.X11 FORTC .EXE Patch File
FORTD.X11 FORTD .EXE Patch File
FORTE.X11 FORTE .EXE Patch File
FORTF.X11 FORTF .EXE Patch File
FORTG.X11 FORTG .EXE Patch File
FORTRA.X11 FORTRA.EXE Patch File
SINGLE.X11 SINGLE.EXE Patch File
SPROUT.C11 SPROUT.MAC Patch File GALAXY-10-V702
LNKHST.C11 LNKHST.MAC Patch File LINK-10-V5-1
LNKLOD.C11 LNKLOD.MAC Patch File
LNKPAR.C11 LNKPAR.MAC Patch File
OVRLAY.C11 OVRLAY.MAC Patch File
DMC.X11 DMC.TSK Patch File MCB-10-V702
DMC.Y11 DMC.STB Patch File
DMR.X11 DMR.TSK Patch File
DMR.Y11 DMR.STB Patch File
NML.X11 NML.TSK Patch File
NML.Y11 NML.STB Patch File
NMS.X11 NMS.TSK Patch File
NMS.Y11 NMS.STB Patch File
RSX11S.X11 RSX11S.TSK Patch File
SC.X11 SC.TSK Patch File
SC.Y11 SC.STB Patch File
TLI.X11 TLI.TSK Patch File
TLI.Y11 TLI.STB Patch File
VNP36.X11 VNP36.EXE Patch File
XPE.X11 XPE.TSK Patch File
XPE.Y11 XPE.STB Patch File
XPT.X11 XPT.TSK Patch File
XPT.Y11 XPT.STB Patch File
DMC.MAP Replacement Files
DMR.MAP
NML.MAP
NMS.MAP
SC.MAP
TLI.MAP
XPE.MAP
XPT.MAP
SRTPRM.C11 SRTPRM.MAC Patch File SORT-10-V4C
Page 11
ROUTER.C11 ROUTER.MAC Patch File TOPS-10-DCN-V702
AUTCON.C11 AUTCON.MAC Patch File KL TOPS-10-K?-V702
CD2SER.C11 CD2SER.MAC Patch File KS
CLOCK1.C11 CLOCK1.MAC Patch File
COMCON.C11 COMCON.MAC Patch File
COMDEV.C11 COMDEV.MAC Patch File
COMMOD.C11 COMMOD.MAC Patch File
COMMON.C11 COMMON.MAC Patch File
CORE1.C11 CORE1 .MAC Patch File
FILFND.C11 FILFND.MAC Patch File
FILIO.C11 FILIO .MAC Patch File
FILUUO.C11 FILUUO.MAC Patch File
IPCSER.C11 IPCSER.MAC Patch File
KLSER.C11 KLSER .MAC Patch File KL
KSSER.C11 KSSER .MAC Patch File KS
LP2SER.C11 LP2SER.MAC Patch File KS
NETSER.C11 NETSER.MAC Patch File
RDXSER.C11 RDXSER.MAC Patch File
SCNSER.C11 SCNSER.MAC Patch File
SEGCON.C11 SEGCON.MAC Patch File
T78KON.C11 T78KON.MAC Patch File KL
TAPSER.C11 TAPSER.MAC Patch File
TAPUUO.C11 TAPUUO.MAC Patch File
TRHKON.C11 TRHKON.MAC Patch File KS
UUOCON.C11 UUOCON.MAC Patch File
VMSER.C11 VMSER.MAC Patch File
BACKUP.C11 BACKUP.MAC Patch File UTILITIES-10-V702
DIRECT.C11 DIRECT.MAC Patch File
FILCOM.C11 FILCOM.MAC Patch File
INITIA.C11 INITIA.MAC Patch File
PFH.C11 PFH .MAC Patch File
SYSTAT.C11 SYSTAT.MAC Patch File
Page 12
Base Building Software
ACTSYM.UNV MACRO.EXE
COMPIL.EXE MACSYM.UNV
CREF.EXE MACTEN.UNV
D60JSY.MAC MAKLIB.EXE
D60JSY.REL NCPTAB.REL
D60UNV.MAC ORNMAC.UNV
D60UNV.UNV OVRLAY.REL
DIRECT.EXE PIP.EXE
EDDT.REL QSRMAC.UNV
GLOB.EXE SCAN.REL
GLXLIB.REL SCNMAC.UNV
GLXMAC.UNV TECO.EXE
HELPER.REL UFDPRM.UNV
JOBDAT.REL UFDSET.REL
JOBDAT.UNV UUOSYM.UNV
LINK.EXE WILD.REL
LNK999.EXE
LNKERR.EXE
LNKLOD.EXE
LNKMAP.EXE
LNKOV1.EXE
LNKOV2.EXE
LNKSCN.EXE
LNKXIT.EXE
Patch BACKUP Command Files
ANFV23.P11 Restores files from Patch Set #011 for ANF10-V23
CBL12B.P11 Restores files from Patch Set #011 for COBOL-10-V12B
DCN702.P11 Restores files from Patch Set #011 for TOPS-10-DCN-V702
FTN10.P11 Restores files from Patch Set #011 for FORTRAN-10-V10
FTN10R.P11 Restores files from Patch Set #011 for FORTRAN-REP-V10
GAL702.P11 Restores files from Patch Set #011 for GALAXY-10-V702
LNKV51.P11 Restores files from Patch Set #011 for LINK-10-V5-1
MCB702.P11 Restores files from Patch Set #011 for MCB-10-V702
SRTV4C.P11 Restores files from Patch Set #011 for SORT-10-V4C
T1L702.P11 Restores files from Patch Set #011 for TOPS-10-KL-V702
T1S702.P11 Restores files from Patch Set #011 for TOPS-10-KS-V702
UTL702.P11 Restores files from Patch Set #011 for UTILITIES-10-V702
Page 13
Patch BACKUP Command Files
ALG10B.A11 Restores files from ALL Patch Sets for ALGOL-10-V10B
ANFV23.A11 Restores files from ALL Patch Sets for ANF10-V23
APL1B2.A11 Restores files from ALL Patch Sets for APL-10-V2
APL1S2.A11 Restores files from ALL Patch Sets for APLSF-10-V2
CBL12B.A11 Restores files from ALL Patch Sets for COBOL-10-V12B
DBMV5A.A11 Restores files from ALL Patch Sets for DBMS-10-V5A
DCN702.A11 Restores files from ALL Patch Sets for TOPS-10-DCN-V702
DNU702.A11 Restores files from ALL Patch Sets for DECNET-10-UTILITIES-V702
FTN10.A11 Restores files from ALL Patch Sets for FORTRAN-10-V10
FTN10R.A11 Restores files from ALL Patch Sets for FORTRAN-REP-V10
GAL702.A11 Restores files from ALL Patch Sets for GALAXY-10-V702
IETV04.A11 Restores files from ALL Patch Sets for IBMCOM-10-ET-V4
IHSV01.A11 Restores files from ALL Patch Sets for IBMCOM-10-HASP-V1
LNKV51.A11 Restores files from ALL Patch Sets for LINK-10-V5-1
MCB702.A11 Restores files from ALL Patch Sets for MCB-10-V702
MPE702.A11 Restores files from ALL Patch Sets for TOPS-10-MPE-V702
MS1V10.A11 Restores files from ALL Patch Sets for MS-10-V10
RMS1V1.A11 Restores files from ALL Patch Sets for RMS-10-V1
SRTV4C.A11 Restores files from ALL Patch Sets for SORT-10-V4C
T1L702.A11 Restores files from ALL Patch Sets for TOPS-10-KL-V702
T1S702.A11 Restores files from ALL Patch Sets for TOPS-10-KS-V702
UTL702.A11 Restores files from ALL Patch Sets for UTILITIES-10-V702
5.0 PRODUCT DOCUMENTATION
Page 14
ALGOL-10-V10B Product Information PRODUCT CODE:
Patch Set 011 ALG10B
This patch set does not provide any edits for ALGOL-10-V10B.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the ALGOL-10-V10B
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The ALG10B.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
If using Autopatch for the first time on this product you may use the
ALG10B.A11 Patch BACKUP Command file to restore files from all Patch
Sets.
Page 15
ANF10-V23 Product Information PRODUCT CODE:
Patch Set 011 ANFV23
This patch set provides the required files to update ANF10-V23 to edit
level 96.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the TOPS-10 distribution
tape. This process is described in the INSTAL.DOC file in the second
save set on this tape and in the Autopatch Procedures/Reference Manual.
The ANFV23.CCL, T1L702.CCL or T1S702.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
A description of each edit is contained in the Edit Description file in
Patch Set 011 (ANFV23.D11).
The files required from Patch Set 011 to patch this product are:
PAT111.DPD
and all the Patch Files listed in section 4.0 for this product
You may use the ANFV23.P11 Patch BACKUP Command file to restore files
from Patch Set 011.
If you are using Autopatch for the first time on this product you may
use the ANFV23.A11 Patch BACKUP Command file to restore files from all
Patch Sets.
Page 16
APL-10-V2 Product Information PRODUCT CODE:
Patch Set 011 APL1B2
This patch set does not provide any edits for APL-10-V2.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the APL-10-V2 distribution
tape. This process is described in the INSTAL.DOC file in the second
save set on this tape and in the Autopatch Procedures/Reference Manual.
The APL1B2.CCL Distribution BACKUP Command file found in the
Installation Save Set may be used for this purpose. If using Autopatch
for the first time on this product you may use the APL1B2.A11 Patch
BACKUP Command file to restore files from all Patch Sets.
Page 17
APLSF-10-V2 Product Information PRODUCT CODE:
Patch Set 011 APL1S2
This patch set does not provide any edits for APLSF-10-V2.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the APLSF-10-V2
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The APL1S2.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
If using Autopatch for the first time on this product you may use the
APL1S2.A11 Patch BACKUP Command file to restore files from all Patch
Sets.
Page 18
COBOL-10-V12B Product Information PRODUCT CODE:
Patch Set 011 CBL12B
This patch set provides the required files to update the COBOL-10-V12B
compiler to edit level 1574, and LIBOL to edit level 1141.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the COBOL-10-V12B
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The CBL12B.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
A description of each edit is contained in the Edit Description file in
Patch Set 011 (CBL12B.D11).
The files required from Patch Set 011 to patch this product are:
PAT111.DPD
and all the Patch Files listed in section 4.0 for this product
You may use the CBL12B.P11 Patch BACKUP Command file to restore files
from Patch Set 011.
If you are using Autopatch for the first time on this product you may
use the CBL12B.A11 Patch BACKUP Command file to restore files from all
Patch Sets.
Page 19
DBMS-10-V5A Product Information PRODUCT CODE:
Patch Set 011 DBMV5A
This patch set does not provide any edits for DBMS-10-V5A.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the DBMS-10-V5A
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The DBMV5A.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
If you are using Autopatch for the first time on this product you may
use the DBMV5A.A11 Patch BACKUP Command file to restore files from all
Patch Sets.
Page 20
DECNET-10-UTILITIES-V702 Product Information PRODUCT CODE:
Patch Set 011 DNU702
This patch set does not provide any edits for DECNET-10-UTILITIES-V702.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the DECNET 10 V7.02
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The DNU702.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
If using Autopatch for the first time on this product you may use the
DNU702.A11 Patch BACKUP Command file to restore files from all Patch
Sets.
Page 21
FORTRAN-10-V10 Product Information PRODUCT CODE:
Patch Set 011 FTN10
This patch set provides the required files to update the Fortran
compiler to edit level 2536, the OTS to edit level 4214, and the DDT to
edit level 336.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the FORTRAN-10-V10
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The FTN10.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
A description of each edit is contained in the Edit Description file in
Patch Set 011 (FTN10.D11).
The files required from Patch Set 011 to patch this product are:
PAT111.DPD
and all the Patch Files listed in section 4.0 for this product
You may use the FTN10.P11 Patch BACKUP Command file to restore files
from Patch Set 011.
If you are using Autopatch for the first time on this product you may
use the FTN10.A11 Patch BACKUP Command file to restore files from all
Patch Sets.
This product may be Autopatched via EXE/REL replacement. The
FTN10R.CCL, FTN10R.A11 and FTN10R.P11 files are provided for this
purpose. See the INSTAL.DOC file for more details.
Page 22
GALAXY-10-V702 Product Information PRODUCT CODE:
Patch Set 011 GAL702
This patch set provides the required files to update SPROUT to edit
level 2542.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the TOPS-10 V702 CUSP
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The GAL702.CCL or CSP702.CCL Distribution
BACKUP Command file found in the Installation Save Set may be used for
this purpose.
A description of each edit is contained in the Edit Description file in
Patch Set 011 (GAL702.D11).
The files required from Patch Set 011 to patch this product are:
PAT111.DPD
and all the Patch Files listed in section 4.0 for this product
You may use the GAL702.P11 Patch BACKUP Command file to restore files
from Patch Set 011.
If you are using Autopatch for the first time on this product you may
use the GAL702.A11 Patch BACKUP Command file to restore files from all
Patch Sets.
Page 23
IBMCOM-10-ET-V4 Product Information PRODUCT CODE:
Patch Set 011 IETV04
This patch set does not provide any edits for IBMCOM-10-ET-V4.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the IBMCOM-10-ET-V4
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The IETV04.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
If using Autopatch for the first time on this product you may use the
IETV04.A11 Patch BACKUP Command file to restore files from all Patch
Sets.
Page 24
IBMCOM-10-HASP-V1 Product Information PRODUCT CODE:
Patch Set 011 IHSV01
This patch set does not provide any edits for IBMCOM-10-HASP-V1.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the IBMCOM-10-HASP-V1
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The IHSV01.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
If using Autopatch for the first time on this product you may use the
IHSV01.A11 Patch BACKUP Command file to restore files from all Patch
Sets.
Page 25
LINK-10-V5-1 Product Information PRODUCT CODE:
Patch Set 011 LNKV51
This patch set provides the required files to update LINK to edit level
2103.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the TOPS-10 V702 CUSP
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The LNKV51.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
A description of each edit is contained in the Edit Description file in
Patch Set 011 (LNKV51.D11).
The files required from Patch Set 011 to patch this product are:
PAT111.DPD
and all the Patch Files listed in section 4.0 for this product
You may use the LNKV51.P11 Patch BACKUP Command file to restore files
from Patch Set 011.
If you are using Autopatch for the first time on this product you may
use the LNKV51.A11 Patch BACKUP Command file to restore files from all
Patch Sets.
Page 26
MCB-10-V702 Product Information PRODUCT CODE:
Patch Set 011 MCB702
This patch set provides the required files to update MCB-10-V702 to edit
level 10.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the MCB-10-V702
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The MCB702.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
A description of each edit is contained in the Edit Description file in
Patch Set 011 (MCB702.D11).
The files required from Patch Set 011 to patch this product are:
PAT111.DPD
and all the Patch Files listed in section 4.0 for this product
You may use the MCB702.P11 Patch BACKUP Command file to restore files
from Patch Set 011. If using Autopatch for the first time on this
product you may use the MCB702.A11 Patch BACKUP Command file to restore
files from all Patch Sets.
Page 27
MS-10-V10 Product Information PRODUCT CODE:
Patch Set 011 MS1V10
This patch set does not provide any edits for MS-10-V10.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the MS-10-V10 distribution
tape. This process is described in the INSTAL.DOC file in the second
save set on this tape and in the Autopatch Procedures/Reference Manual.
The MS1V10.CCL Distribution BACKUP Command file found in the
Installation Save Set may be used for this purpose.
If you are using Autopatch for the first time on this product you may
use the MS1V10.A11 Patch BACKUP Command file to restore files from all
Patch Sets.
Page 28
RMS-10-V1 Product Information PRODUCT CODE:
Patch Set 011 RMS1V1
This patch set does not provide any edits for RMS-10-V1.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the TOPS-10 V7.02 CUSP
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The RMS1V1.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
If you are using Autopatch for the first time on this product you may
use the RMS1V1.A11 Patch BACKUP Command file to restore files from all
Patch Sets.
Page 29
SORT-10-V4C Product Information PRODUCT CODE:
Patch Set 011 SRTV4C
This patch set provides the required files to update SORT-10-V4C to edit
level 531.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the COBOL-10-V12B or
SORT-10-V4C distribution tape. This process is described in the
INSTAL.DOC file in the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The SRTV4C.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
to edit level
A description of each edit is contained in the Edit Description file in
Patch Set 011 (SRTV4C.D11).
The files required from Patch Set 011 to patch this product are:
PAT111.DPD
and all the Patch Files listed in section 4.0 for this product.
You may use the SRTV4C.P11 Patch BACKUP Command file to restore files
from Patch Set 011.
If you are using Autopatch for the first time on this product you may
use the SRTV4C.A11 Patch BACKUP Command file to restore files from all
Patch Sets.
Page 30
TOPS-10-DCN-V702 Product Information PRODUCT CODE:
Patch Set 011 DCN702
This patch set provides the required files to update TOPS-10-DCN-V702 to
edit level 11872.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the TOPS-10 V702 DECNET
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The DCN702.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
A description of each edit is contained in the Edit Description file in
Patch Set 011 (DCN702.D11).
The files required from Patch Set 011 to patch this product are:
PAT111.DPD
and all the Patch Files listed in section 4.0 for this product
You may use the DCN702.P11 Patch BACKUP Command file to restore files
from Patch Set 011. If using Autopatch for the first time on this
product you may use the DCN702.A11 Patch BACKUP Command file to restore
files from all Patch Sets.
Page 31
TOPS-10-KL-V702 Product Information PRODUCT CODE:
Patch Set 011 T1L702
This patch set provides the required files to update the TOPS-10-KL-V702
monitor to edit level 11600 (27647).
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the TOPS-10 V7.02
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The MON702.CCL, CSC702.CCL and CSP702.CCL
Distribution BACKUP Command files found in the Installation Save Set may
be used for this purpose.
A description of each edit is contained in the Edit Description file in
Patch Set 011 (T1L702.D11).
The files required from Patch Set 011 to patch this product are:
PAT111.DPD
and all the Patch Files listed in section 4.0 for this product
You may use the T1L702.P11 Patch BACKUP Command file to restore files
from Patch Set 011.
If you are using Autopatch for the first time on this product you may
use the T1L702.A11 Patch BACKUP Command file to restore files from all
Patch Sets.
Page 32
TOPS-10-KS-V702 Product Information PRODUCT CODE:
Patch Set 011 T1S702
This patch set provides the required files to update the TOPS-10-KS-V702
monitor to edit level 11600 (27647).
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the TOPS-10 V7.02
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The MON702.CCL, CSC702.CCL and CSP702.CCL
Distribution BACKUP Command files found in the Installation Save Set may
be used for this purpose.
A description of each edit is contained in the Edit Description file in
Patch Set 011 (T1S702.D11).
The files required from Patch Set 011 to patch this product are:
PAT111.DPD
and all the Patch Files listed in section 4.0 for this product
You may use the T1S702.P11 Patch BACKUP Command file to restore files
from Patch Set 011.
If you are using Autopatch for the first time on this product you may
use the T1S702.A11 Patch BACKUP Command file to restore files from all
Patch Sets.
Page 33
TOPS-10-MPE-V702 Product Information PRODUCT CODE:
Patch Set 011 MPE702
This patch set does not provide any edits for TOPS-10-MPE-V702.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the TOPS-10 MPE V7.02
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The MPE702.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
If you are using Autopatch for the first time on this product you may
use the MPE702.A11 Patch BACKUP Command file to restore files from all
Patch Sets.
Page 34
UTILITIES-10-V702 Product Information PRODUCT CODE:
Patch Set 011 UTL702
This patch set provides the required files to update BACKUP to edit
level 525, DIRECT to edit level 466, FILCOM to edit level 111, INITIA to
edit level 236, PFH to edit level 55, and SYSTAT to edit level 326.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the TOPS-10 702 CUSP
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The UTL702.CCL or CSP702.CCL Distribution
BACKUP Command file found in the Installation Save Set may be used for
this purpose.
A description of each edit is contained in the Edit Description file in
Patch Set 011 (UTL702.D11).
The files required from Patch Set 011 to patch this product are:
PAT111.DPD
and all the Patch Files listed in section 4.0 for this product
You may use the UTL702.P11 Patch BACKUP Command file to restore files
from Patch Set 011.
If you are using Autopatch for the first time on this product you may
use the UTL702.A11 Patch BACKUP Command file to restore files from all
Patch Sets.