Trailing-Edge
-
PDP-10 Archives
-
bb-jr93h-bb
-
7,6/ap021/pltser.x21
There are 3 other files named pltser.x21 in the archive. Click here to see a list.
TITLE PLTSER - PLOTTER SERVICE ROUTINE - V052
SUBTTL T. EGGERS/GBH/TNM/RCC 25 OCTOBER 88
SEARCH F,S,DEVPRM
$RELOC
$HIGH
;THIS SOFTWARE IS FURNISHED UNDER A LICENSE AND MAY BE USED
; OR COPIED ONLY IN ACCORDANCE WITH THE TERMS OF SUCH LICENSE.
;
;COPYRIGHT (c) DIGITAL EQUIPMENT CORPORATION
; 1973,1974,1975,1976,1977,1978,1979,1980,1982,1984,1986,1988.
;ALL RIGHTS RESERVED.
.CPYRT<1973,1988>
XP VPLTSR,052 ;PUT VERSION NUMBER IN STORAGE MAP AND GLOB
PLTSER::ENTRY PLTSER ;LOAD IF LIBRARY SEARCH
SUBTTL DEVICE DEFINITIONS
;DATAO BITS
PEN.UP==40 ;LIFT THE PEN
PEN.DN==20 ;LOWER THE PEN
NEG.X== 10 ;ROLL DRUM BACK
POS.X== 4 ;ROLL DRUM FORWARD
POS.Y== 2 ;MOVE CARRIAGE LEFT
NEG.Y== 1 ;MOVE CARRIAGE RIGHT
;CONI BITS
PLBUSY==20 ;PLOTTER IS BUSY
PLDONE==10 ;PLOTTER DONE FLAG
PLPICH== 7 ;PI CHANNEL ASSIGNMENT
PLTUP==200000 ;LIFT PEN WHEN OUTPUT FINISHED
SUBTTL AUTOCONFIGURE
;DRIVER CHARARCTERISTICS
; PLT = PLTCNF
; PLT = PLOTTER
; 7 = MAXIMUM DEVICES IN SYSTEM
; 0 = KONTROLLER TYPE
; 0 = MAXIMUM DRIVES PER KONTROLLER
; 0 = HIGHEST DRIVE NUMBER ON KONTROLLER
; MDSEC0 = SECTION FOR KDB/UDB
; MDSEC0 = SECTION FOR DDB
DRVCHR (PLT,PLT,7,0,0,0,MDSEC0,MDSEC0,<DR.GCC!DR.NET>)
.ORG DEVLEN
PLTCSO:! BLOCK 1 ;ADDRESS OF INTERRUPT CODE
PLTIOB:! ;START OF I/O INSTRUCTIONS
PLTCNO:! BLOCK 1 ;CONO
PLTDTO:! BLOCK 1 ;DATAO
PLTIOE:! ;END OF I/O INSTRUCTIONS
PLTLEN:! ;LENGTH OF PLT DDB
.ORG
$LOW
PLTDDB: DDBBEG (PLT,PLTLEN)
SETWRD (DEVCHR,<4*HUNGST,,PLTSIZ##>) ;DEVCHR
SETWRD (DEVSER,<MCSEC0+PLTDSP>) ;DEVSER
SETWRD (DEVMOD,<DVOUT,,<1_A+1_AL+1_I+1_IB+1_B>>) ;DEVMOD
SETWRD (DEVTYP,<<.TYPLT*.TYEST>!.SPPLT,,0>) ;DEVTYP
SETWRD (DEVCPU,<PLTCHN##>) ;DEVCPU
SETWRD (PLTCNO,<CONO 000,(T1)>) ;CONO
SETWRD (PLTDTO,<DATAO 000,T1>) ;DATAO
DDBEND
$HIGH
;CONSO SKIP CHAIN CODE (AUTCON WILL FILL IN THE BLANKS)
PLTICD: PHASE 0
CONSO 000,0 ;(00) SKIP IF INTERRUPT FOR THIS LPT
JRST .-1 ;(01) GO TO NEXT SKIP CHAIN ELEMENT
PLTCTA:!SOSGE DEVCTR ;(02) OUTPUT CHARACTERS LEFT?
JRST PLTINX ;(03) NO
MOVEM T1,PLTSV1 ;(04) SAVE T1
PLTPTA:!ILDB T1,DEVPTR ;(05) GET NEXT CHARACTER
DATAO 000,T1 ;(06) SEND TO PLOTTER
MOVE T1,PLTSV1 ;(07) RESTORE T1
XJEN -1 ;(10) DONE
PLTINX:!JSR PIERR## ;(11) SAVE ACS AND SETUP PDL
SKIPA F,.+1 ;(12) SET UP DDB ADDRESS
PLTDDA:!EXP 0 ;(13) DDB ADDRESS
XJRST .+1 ;(14) CALL INTERRUPT HANDLER
PLTICN:!EXP 0 ;(15) INTERRUPT HANDLER ADDRESS
PLTSV1:!EXP -1 ;(16) STORAGE FOR AC T1
DEPHASE
PLTICL==.-PLTICD ;LENGTH OF CONSO SKIP CHAIN CODE
EQUATE (LOCAL,0,<PLTCKT,PLTKDB,PLTKLN,PLTUDB,PLTULN>)
EQUATE (LOCAL,0,<PLTULB,PLTULP>)
PLXDSP: DRVDSP (PLT,PLTCHN##,PLTDDB,PLTLEN,URDDIA##)
;DEFAULT MONGEN'ED DEVICE TABLE
DEFMDT: MDKL10 (7,140,0,0,<MD.KON>) ;DEVICE CODE 140
MDKL10 (7,144,0,0,<MD.KON>) ;DEVICE CODE 144
EXP 0
PLTCFG: XMOVEI T1,PLTMDT## ;MONGEN'ED DEVICE TABLE
XMOVEI T2,DEFMDT ;DEFAULT TABLE
MOVNI T3,1 ;NO MASSBUS UNIT OR DRIVE INFORMATION
MOVEI T4,MD.KON ;MATCH ON KONTROLLER DEFINITION
PUSHJ P,AUTMDT## ;SCAN THE TABLES
JRST CPOPJ1## ;NO MATCHES
PUSH P,T1 ;SAVE MDT DATA
MOVEI T1,PLTIOB ;WORD CONTAINING AN I/O INSTRUCTION
PUSHJ P,AUTFND## ;SEE IF THERE'S ALREADY A DDB
JRST PLTCF1 ;JUST MAKE SURE THE NUMBERS ARE OK
PUSHJ P,AUTADN## ;ALLOCATE A DEVICE NUMBER
HRLI T1,'PLT' ;INCLUDE GENERIC DEVICE NAME
SETZ T2, ;LOCAL DEVICE
PUSHJ P,AUTDDB## ;CREATE A DDB
JRST [POP P,T1 ;NO CORE
PJRST AUTDDN##] ;DEALLOCATE DEVICE NUMBER
PLTCF1: MOVSI T1,-<PLTIOE-PLTIOB> ;-LENGTH
XMOVEI T2,PLTIOB(F) ;STARTING ADDRESS
HRRZ T3,.CPDVC## ;DEVICE CODE
PUSHJ P,AUTDVC## ;FILL IN DEVICE CODES
SKIPE PLTCSO(F) ;BEEN HERE BEFORE?
JRST PLTCF3 ;THEN DON'T MESS WITH THE SKIP CHAIN
MOVE T1,F ;DATA BLOCK ADDRESS
XMOVEI T2,PLTINT ;INTERRUPT SERVICE
PUSHJ P,AUTICD## ;GENERATE INTERRUPT ROUTINES
SKIPA T2,F ;NO CORE
JRST PLTCF2 ;ONWARD
MOVEI T1,PLTLEN ;GET DDB LENGTH
PUSHJ P,AUTKIL## ;DELETE THE DDB
PUSHJ P,AUTDDN## ;DEALLOCATE DEVICE NUMBER
JRST TPOPJ## ;PHASE STACK AND RETURN
PLTCF2: MOVEM T1,PLTCSO(F) ;SAVE ADDRESS
MOVEI T2,DEVCTR(F) ;COUNTER ADDRESS
HRRM T2,PLTCTA(T1) ;RELOCATE DDB BYTE COUNTER
MOVEI T2,DEVPTR(F) ;BYTE POINTER ADDRESS
HRRM T2,PLTPTA(T1) ;RELOCATE DDB BYTE POINTER
MOVEI T2,PLTCHN## ;PI CHANNEL
PUSHJ P,AUTCSO## ;LINK INTO CONSO SKIP CHAIN
PLTCF3: POP P,T1 ;GET MDT DATA BACK
POPJ P, ;ALL DONE
;DISPATCH TABLE
JRST CPOPJ1## ;IF YOU'RE ASKING, IT'S ONLINE
JRST ECOD2## ;SPECIAL ERROR STATUS
JRST REGSIZ## ;BUFFER LENGTH CAN BE GOTTEN FROM DDB
JRST PLTINI ;INITIALIZE
JRST PLTHNG ;HUNG DEVICE ERROR
PLTDSP: JRST PLTREL ;RELEAS
JRST PLTCLS ;CLOSE
JRST PLTOUT ;OUTPUT
JRST ILLINP## ;INPUT
PLTCLS: TLO S,PLTUP ;PLOTTER END FLAG SET
MOVEM S,DEVIOS(F)
JRST OUT## ;DO AN OUTPUT
PLTINI: MOVEI PLTDDB ;ADDRESS OF PROTOTYPE
CAIN T1,(F) ;IF CALLED FOR PROTOTYPE,
JRST CPOPJ1## ;HOLD OUT FOR A REAL PLOTTER
AOS (P) ;CALL FOR EACH PLOTTER (AS IF THERE WERE TWO)
PLTHNG:
PLTREL: MOVEI T1,0
XCT PLTCNO(F) ;DEASSIGN PI CHANNEL, CLEAR DONE
HLLZS @PLTCSO(F) ;REMOVE PLOTTER FROM DEVICE CHAIN
POPJ P,
;HERE BEGINS THE "OUTPUT" UUO
PLTOUT: PUSHJ P,PLTSET ;SETUP BYTE POINTER AND COUNTER
PUSHJ P,SETACT## ;SET DEVICE ACTIVE BIT
TLO S,IO
MOVEI T1,10
HRRM T1,@PLTCSO(F) ;PUT PLOTTER INTO DEVICE CHAIN
MOVEI T1,PLTCHN## ;GET INTERRUPT CHANNEL
XCT PLTCNO(F) ;ASSIGN PRIORITY CHANNEL
TLZE S,IOBEG ;FIRST OUTPUT UUO?
TLZA S,PLTUP ;YES, INIT "CLOSE" BIT
TDZA T1,T1 ;NO, 1ST PLOT CHAR IS ZERO
MOVEI T1,PEN.UP ;START PLOT WITH PEN UP
MOVEM S,DEVIOS(F)
XCT PLTDTO(F) ;START PLOTTER BY SENDING PEN.UP OR A NO-OP
POPJ P,
;FROM HERE THROUGH PLTOFF IS INTERRUPT SERVICE
PLTINT: ;THE PLOTTER CODE IN COMDEV TAKES CARE OF PLOTTER
;DATA INTERRUPTS THAT REQUIRE ONLY A CHARACTER THAT
;IS READILY AVAILABLE. TO ADVANCE BUFFERS OR SHUT
;DOWN THE PLOTTER, THE CODE HERE FOLLOWING IS CALLED.
PUSHJ P,IOSET## ;SETS UP R AND S
PUSHJ P,ADVBFE## ;ADVANCE AND LOOK AT NEXT BUFFER
JRST PLTOFF ;NO MORE DATA AVAILABLE
PUSHJ P,PLTSET ;SETUP BYTE POINTER AND COUNTER
PLT2: PUSHJ P,SETIOD## ;LET JOB START AGAIN
JRST STOIOS## ;EVENTUALLY DISMISS INTERRUPT. IF ADVBFE
;FOUND MORE DATA (IT SKIPPED), ANOTHER
;INTERRUPT WILL IMMEDIATELY OCCUR BUT
;IT WILL BE HANDLED WITHOUT GOING TO PLTNXT
PLTOFF: PUSHJ P,PLTREL ;SHUT DOWN PLOTTER
TRZ S,IOACT
MOVEI T1,PEN.UP ;PEN UP COMMAND
TLZE S,PLTUP ;HAS THE "CLOSE" BEEN DONE?
XCT PLTDTO(F) ;YES, LIFT PEN
JRST PLT2
;THIS SUBROUTINE CALCULATES A BYTE POINTER AND A BYTE COUNTER FOR
;THE BUFFER TO BE OUTPUT.
PLTSET: MOVEI T1,@DEVOAD(F) ;GET ADDRESS OF CURRENT BUFFER
ADD T1,[POINT 6,1,35] ;CONVERT TO 6 BIT BYTE POINTER WITH
;ADDRESS OF BUFFER WORD COUNT
TRNN S,16 ;IS THIS A TEXT DATA MODE?
HRLI T1,(POINT 7,0,35) ;YES, CONVERT TO 7 BIT BYTE POINTER
MOVEM T1,DEVPTR(F) ;SAVE BYTE POINTER
HRRZ T1,@T1 ;GET BUFFER WORD COUNT
MOVEM T1,DEVCTR(F) ;SAVE AS POSITIVE WORD COUNT
MOVEI T1,6 ;IMAGE OR BIN MODES - 6 BYTES/WORD
TRNN S,16 ;IS OUTPUT A TEXT MODE (0 OR 1)?
MOVEI T1,5 ;YES, 5 BYTES/WORD
IMULM T1,DEVCTR(F) ;CHANGE WORD COUNT TO BYTE COUNT
POPJ P, ;RETURN
LIT
PLTEND: END