Trailing-Edge
-
PDP-10 Archives
-
dec-10-omona-u-mc9
-
stopcd.rno
There are no other files named stopcd.rno in the archive.
.SP 1
.PS 64,70
.F
.J
.LM 0
.RM 70
.TS 10,35,45
.PG
^^SPECIFICATION\\
.FG 5;.C
^^STOPCD
.B 1;.C
LIST OF MONITOR ERROR STOPS\\
.B 10;.LM 20
^DATE:#####^JULY,#1975
.BR
^FILE:#####^^STOPCD.RNO\\
.BR
^EDITION:##3
.B10;.LM0;.RM70
^THIS DOCUMENT REFLECTS THE 6.02 RELEASE OF THE MONITOR.
.B 1
^THE INFORMATION IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ^DIGITAL ^EQUIPMENT ^CORPORATION.
^DIGITAL ^EQUIPMENT ^CORPORATION ASSUMES NO RESPONSIBILITY FOR ANY
ERRORS THAT MAY APPEAR IN THIS MANUAL.
.B1
^THE SOFTWARE DESCRIBED IN THIS DOCUMENT IS FURNISHED TO THE
PURCHASER UNDER A LICENSE FOR USE ON A SINGLE COMPUTER
SYSTEM AND CAN BE COPIED (WITH INCLUSION OF ^^DIGITAL\\'S
COPYRIGHT NOTICE) ONLY FOR USE IN SUCH SYSTEM, EXCEPT AS
MAY OTHERWISE BE PROVIDED IN WRITING BY ^^DIGITAL\\.
.B1
^DIGITAL ^EQUIPMENT ^CORPORATION ASSUMES NO RESPONSIBILITY
FOR THE USE OR RELIABILITY OF ITS SOFTWARE ON EQUIPMENT THAT
IS NOT SUPPLIED BY ^^DIGITAL\\.
.B3
^COPYRIGHT##^C##1971, 1972, 1973, 1974, 1975, BY
^DIGITAL ^EQUIPMENT ^CORPORATION, ^MAYNARD, ^MASSACHUSETTS
.PG;.LM 0;.RM 70
1.0##^^INTRODUCTION\\
.B 1
^THIS DOCUMENT DESCRIBES THE DIFFERENT TYPES OF ERROR STOPS IN THE
MONITOR AND THEN LISTS ALL THE ERROR STOPS THAT CAN OCCUR.
^WHEN THE MONITOR DETECTS AN INTERNAL ERROR IT
EXECUTES THE ^^STOPCD\\ MACRO WHICH PRODUCES
A MESSAGE OF THE FORM:
.B 1;.I 10
?^^CPU\\N#^^MONITOR ERROR. STOPCODE NAME\\ XXX
.B 1
WHERE N IS THE NUMBER OF THE ^^CPU\\ THAT EXECUTED THE ^^STOPCD\\
MACRO AND XXX IS A MNEMONIC IN THE ^^STOPCD\\ MACRO. ^THESE MNEMONICS
ARE LISTED IN ^SECTION 2.0 OF THIS DOCUMENT. ^ALSO LISTED ARE THE NAME OF THE
MONITOR MODULE CONTAINING THE ^^STOPCD\\, THE TYPE OF
^^STOPCD\\, AND A BRIEF EXPLANATION.
.B 1
^THERE ARE FOUR TYPES OF ^^STOPCD\\'S:
.B 1;.LM 9;.I -4
1.##^^DEBUG\\#-# ^IF A PRIORITY INTERRUPT IS IN PROGRESS,
THE CONDITION IS NOT IMMEDIATELY HARMFUL TO
ANY JOB OR TO THE SYSTEM. ^THE MONITOR TRANSMITS THE FOLLOWING
MESSAGE TO THE ^^CTY\\:
.B 1;.LM 14
^^?CPU\\N ^^MONITOR ERROR. STOPCODE NAME\\ XXX
.BR
^^CONTINUING SYSTEM\\
.B 1;.LM 9
AND CONTINUES. ^NO IMMEDIATE OPERATOR ACTION IS REQUIRED.
.B 1
^IF NO PRIORITY INTERRUPT IS IN PROGRESS, A ^^DEBUG STOPCD\\
ACTS AND COUNTS AS A ^^JOB STOPCD\\.
.B 1;.I -4
2.##^^JOB\\#-# ^IF NO PRIORITY INTERRUPT IS IN PROGRESS,
THE CONDITION JEOPARDIZES THE INTEGRITY OF THE
CURRENT JOB. ^THE MONITOR TRANSMITS THE FOLLOWING MESSAGE TO THE
^^CTY\\:
.B 1;.LM 14
^^?CPU\\N ^^MONITOR ERROR. STOPCODE NAME\\ XXX
.BR
?^^ABORTING JOB\\
.B 1;.LM 9
AND ANOTHER MESSAGE TO THE USER'S TERMINAL:
.B1;.I 5
?^^MONITOR ERROR; UUO AT\\ XXXXXXXX
.B 1
WHERE XXXXXXXX IS ONE OF THE FOLLOWING:
.B 1;.I 5
^^USER LOC\\ N
.I 5
^^EXEC LOC\\ N; ^^EXEC CALLED FROM EXEC LOC\\ M
.I 5
^^EXEC LOC\\ N; ^^EXEC CALLED FROM USER LOC\\ M
.B 1
^THE MONITOR THEN ABORTS THE CURRENT JOB AND CONTINUES.
^NO IMMEDIATE OPERATOR ACTION IS REQUIRED.
.B 1
^IF A PRIORITY INTERRUPT IS IN PROGRESS, A ^^JOB STOPCD\\
ACTS LIKE A ^^STOP STOPCD\\.
.B 1;.I -4
3.##^^STOP\\#-#^THE CONDITION JEOPARDIZES THE INTEGRITY OF THE
SYSTEM AS A WHOLE. ^THE MONITOR TRANSMITS THE FOLLOWING MESSAGE
TO THE ^^CTY\\:
.B 1;.LM 14
^^?CPU\\N ^^MONITOR ERROR. STOPCODE NAME\\ XXX
.BR
^^RELOAD MONITOR\\
.B 1;.LM 9
^ALL JOBS ARE ABORTED AND THE SYSTEM INITIATES AN AUTOMATIC RELOAD
OF THE MONITOR.
.B 1;.I -4
4.##^^HALT\\#-#^THE CONDITION IS SO SERIOUS THAT THE ENTIRE SYSTEM
IS AFFECTED AND THE MONITOR CANNOT BE RELOADED AUTOMATICALLY.
^THE SYSTEM HALTS REQUIRING THAT THE OPERATOR MANUALLY PERFORM
THE ENTIRE ^^CRASH\\ PROCEDURE AS DESCRIBED IN THE ^SOFTWARE ^NOTEBOOKS
IN THE ^OPERATOR'S
^PROCEDURE ENTITLED ^^CRASH\\, ^SAVING A ^CRASHED ^MONITOR AND
^RESTARTING, OR IN ^CHAPTER 5 OF THE ^OPERATOR'S ^GUIDE.
.B 3;.LM 5
^IN ADDITION, IF THE MONITOR CAN DETERMINE THE INFORMATION, A SUPPLEMENTARY MESSAGE:
.B 1;.LM 9
^^JOB\\ N ^^ON TTY\\XXX ^^RUNNING\\ XXXXXX
.BR
^^UUO IS\\ XXXXXXXXXXXX ^^AT USER PC\\ XXXXXX
.BR
^^FILE\\ DEV:FILE.EXT[N,M]
.B 1;.LM 5
IS TRANSMITTED TO THE ^^CTY\\ AFTER ^^?CPU\\N ^^MONITOR ERROR\\ IN ORDER TO HELP
THE OPERATOR FIND THE USER CAUSING THE PROBLEM.
.B 3;.LM 0
1.1##^^FINDING THE ^^STOPCD'S IN THE ^CODE\\
.B 1
^SOMETIMES ^^STOPCD\\'S COME UP WHICH ARE NOT DOCUMENTED.
^THIS MAY BE THE RESULT OF PATCHES SPECIFIC TO AN INSTALLATION
OR PATCHES MADE AFTER THE RELEASE OF THE MONITOR.
.B 1
^IF A ^^STOPCD\\ MESSAGE COMES UP WHICH CAN NOT BE FOUND
IN THIS MANUAL, THE FOLLOWING PROCEDURE MAY BE USED TO FIND THE
PLACE IN THE CODE WHERE THE ^^STOPCD\\ OCCURRED.
.B 1
^FIRST, CONSULT THE LISTING OF THE MONITOR'S GLOBAL SYMBOLS
^^(GLOB\\). ^THE
^^STOPCD\\'S ARE LISTED AS:
.B 1;.LM 20;.I -20
^^S..XXX#####MODNAM\\###WHERE ^^XXX\\ IS THE MNEMONIC FOR THE
^^STOPCD\\ AND ^^MODNAM\\ IS THE NAME OF THE MODULE WHERE
THE ^^STOPCD\\ IS CODED.
.B 1;.LM 0
^BY CHECKING THE ^^CREF\\ LISTING FOR THE GIVEN MODULE, THE
PROGRAMMER CAN DETERMINE THE LINE NUMBER WHERE THE ^^STOPCD\\
CAN BE FOUND. ^THE COMMENTARY THAT CAN BE FOUND IN THE CODE IS
SOMETIMES SUFFICIENT FOR DETERMINING HOW AN ERROR OCCURRED.
.B 3
1.2##^^HOW TO SET THE MONITOR TO RELOAD ON DEBUG AND JOB STOPCD'S.\\
.B 1
^AS AN ADDED AID TO DEBUGGING IT IS POSSIBLE TO CAUSE A RELOAD ON ALL ^^STOPCD\\'S.
.B 1
^THERE ARE TWO WAYS IN WHICH THE SYSTEM PROGRAMMER CAN SET THE MONITOR TO RELOAD ON
EITHER THE ^^DEBUG\\ OR THE ^^JOB STOPCD\\'S.
^BOTH TECHNIQUES INVOLVE THE SETTING OF BITS FOR THE SYMBOL ^^DEBUGF\\ OR ^^DEFDEB\\. ^THIS CAN BE DONE
BY CHANGING THE CONTENTS OF ^^DEBUGF\\ WITH
^^FILDDT\\ OR ^^EDDT\\, OR DEFINING ^^DEFDEB\\ WITH ^^MONGEN\\. ^THE BIT VALUES ARE:
.B1;.LM21;.TS21;.I-11
BIT#0#=#1 ^THIS ALLOWS SYSTEM DEBUGGING IF ^^EDDT\\ IS AVAILABLE ON THE SYSTEM.
^IF BIT 0 = 0, A RELOAD WILL OCCUR ON ALL ^^STOP STOPCD\\'S,
IF THE SYSTEM HAS BEEN UP AT LEAST 5 MINUTES.
.B 1;.I -11
BIT#1#=#1 ^THIS CAUSES A RELOAD ON ALL ^^DEBUG STOPCD\\'S.
.B 1;.I -11
BIT#2#=#1 ^THIS CAUSES A RELOAD ON ALL ^^JOB STOPCD\\'S.
.B 1;.I -11
BIT#3#=#1 ^THIS DISABLES AUTO RELOAD.
.B 1;.I -11
BIT#4#=#1 ^THIS STOPS THE SYSTEM IF ^^CPU1\\ HALTS.
.B 2
.LM 0
^THE FOLLOWING COMMAND SEQUENCE SHOULD BE USED TO SET THE BITS THROUGH ^^FILDDT\\:
.B 1;.LM 36;.TS 36;.I -31
_.^^R FILDDT
.B 1;.I -31
FILE:##SYSTEM/S\\ ;#THIS LOADS THE SYMBOL TABLE
.B 1;.I -31
^^FILE:##/M/P\\ ;#ENABLES THE USER TO POKE
.BR
;#LOCATIONS
.BR
;#IN THE RUNNING MONITOR.
.B 1;.I -31
^^DEBUGF\\/300000,,0 ;#THIS TURNS ON BOTH BITS 1 AND 2
.BR
;#SO THERE WILL BE A RELOAD ON ALL
.BR
;#^^STOPCD\\'S
.I-31
_^^^Z ;#EXIT\\
.B 1;.LM 0
^THE SAME THING MAY BE ACCOMPLISHED AT ^^MONGEN\\ TIME.
^WHEN THE HARDWARE CONFIGURATION DIALOGUE ASKS FOR:
.B1;.I10
^^OCTAL "SYMBOL, VALUE"\\
.B 1
THE PROGRAMMER SHOULD ENTER:##^^DEFDEB,##300000000000.\\
.B 1
^IF ^^FILDDT\\ WAS USED TO EFFECT THIS CHANGE ON THE RUNNING
MONITOR, ANY CRASHES WIPE OUT THE CHANGE.
^HOWEVER, IF ^^MONGEN\\ WAS USED, THE CHANGE IS STILL IN EFFECT WHEN THE MONITOR IS RELOADED.
^IT IS ALSO POSSIBLE TO PATCH A COPY OF THE
MONITOR ON DISK WITH ^^DDT\\ OR ^^FILDDT\\ TO MAKE THE CHANGE
EFFECTIVE AFTER RELOADS.
.PG;.TS 8,19,44
2.0##^^STOPCODES\\
.B 1
^^NAME ROUTINE TYPE DESCRIPTION\\
.B 2;.LM 30;.TS 8,19,30;.I -30
28^B ^^XTCSER DEBUG\\ ^THE ^^DA28\\ COMMAND REGISTER
CONTAINED ERRONEOUS STATUS BITS DURING AN ^^I/O\\ OPERATION.
.B 1;.I -30
4^^IF FSXKON DEBUG\\ "^^RP04 INVALID FUNCTION".\\ ^^FILIO\\ TRIED
TO DO AN ^^RP04\\ ONLY FUNCTION ON AN ^^RS04\\ LIKE ^^ECC\\
ERROR RECOVERY OR AN UNLOAD.
.B 1;.I -30
^^5WE D85INT DEBUG "DC75 WRONG PDP11 CODE".\\ ^THE ^^PDP11\\
DESIGNATED AS A ^^DC75\\ WAS NOT RUNNING THE PROPER CODE.
.B 1;.I -30
^^6MS D76INT DEBUG\\ ^^"DC76 MESSAGE IS SHORT".\\ ^A PORTION OF A MESSAGE WAS LOST BETWEEN THE ^^DC76\\ AND THE -10.
.B 1;.I -30
^^6PP D76INT STOP\\ "^^DC76 PUTTER PROBLEM".\\ ^THERE WAS AN INTERRUPT LEVEL CALL TO PUTTER
WHILE A NON-INTERRUPT CALL WAS IN PROGRESS.
.B 1;.I -30
^^6QF D76INT DEBUG\\ ^^"DC76 QUEUE FULL".\\ ^THE QUEUE OF MESSAGES TO THE ^^DC76\\ WAS FULL.
^THE QUEUE WAS DESIGNED TO BE BIG ENOUGH TO HOLD THE WORST CASE MESSAGES.
.B 1;.I -30
^^AAD FILFND DEBUG "ACCESS TABLE ALREADY DORMANT".\\
^AN ATTEMPT WAS MADE TO UNLINK AN ACCESS TABLE FROM AN ^^NMB\\
RING, BUT THE ACCESS TABLE WAS ALREADY DORMANT.
.B 1;.I -30
^^AAO KISER JOB "ACCESS ALLOWED OFF"\\.
^WHEN THE# MONITOR
.I -30
^^KLSER\\ WAS REMAPPING ^^IOWD\\'S FROM USER VIRTUAL
ADDRESSES TO PHYSICAL ADDRESSES, A PAGE MAP ENTRY
FETCHED FROM THE USER'S PAGE MAP HAD THE ACCESS ALLOWED BIT OFF
(VIRTUAL MEMORY MONITOR ONLY).
.B 1;.I -30
^^AES FILFND JOB "ABNORMAL END OF SEARCH LIST". FILFND\\
GOT TO THE END OF THE SEARCH LIST WHEN IT DID NOT EXPECT TO BE THERE.
.B1;.I-30
^^AHB FILIO DEBUG "ALREADY HAVE BUFFER".\\ ^THE MONITOR
ATTEMPTED TO GET A MONITOR BUFFER WHEN IT ALREADY HAD ONE.
.B 1;.I -30
^^AHS ONCMOD HALT "ALREADY HAVE STRUCTURE".\\ ^THE TABLES WHICH DRIVE ^^ONCMOD\\'S '^^DESTROY\\' OPTION DUPLICATED A
STRUCTURE NAME.
.B 1;.I -30
^^AOC FILFND DEBUG "ALREADY OWN CB".\\ ^A JOB WANTED THE
^^CB\\ RESOURCE BUT ALREADY HAD IT.
.B 1;.I -30
^^APE KISER JOB\\ "^^ABSOLUTE##PAGE#EXCEEDED".\\##^^MAPIO\\##FOUND
.I -22
^^KLSER\\ AN ^^IOWD\\ WHICH WOULD HAVE CAUSED AN ADDRESS CHECK.
^ALL ^^IOWD\\'S HAVE BEEN CHECKED PRIOR TO CALLING ^^MAPIO\\.
.B 1;.I -30
^^APF VMSER DEBUG "ALLOCATED PAGE FREE".\\ ^WHILE
THE PAGES ALLOCATED TO A SEGMENT WERE BEING SCANNED, A PAGE ON THE FREE
CORE LIST WAS ENCOUNTERED.
.B 1;.I -30
^^AR1 ONCMOD DEBUG "ASKDEC RETURNED CPOPJ1".\\ ^^ASKDEC\\ GAVE A SKIP RETURN WHEN ONE WAS NOT EXPECTED.
.B 1;.I -30
^^ARF KISER STOP "ATTEMPT#TO#RETURN#FREE#PAGE".\\###^A##PAGE
.I -22
^^KLSER\\ THAT WAS GOING TO BE RETURNED TO THE FREE CORE LIST
WAS ALREADY FREE.
.B 1;.I -30
^^BAC CORE1 JOB "BIT ALREADY CLEAR".\\ ^AN ATTEMPT WAS MADE TO ZERO
BITS WHICH WERE NOT ONE. ^THIS IS THE ^^SETZRS\\ ROUTINE
WHICH IS CALLED FROM MANY MODULES.
.B 1;.I -30
^^BAD FILFND JOB "BLOCK ALREADY DORMANT".\\ ^AN ATTEMPT
WAS MADE TO PUT AN ALREADY DORMANT ACCESS TABLE IN THE FREE CORE LIST.
.B 1;.I -30
^^BAO FILIO DEBUG "BIT ALREADY ONE".\\ ^THE MONITOR TRIED TO ALLOCATE A BLOCK WHICH WAS ALREADY ALLOCATED.
.B 1;.I -30
^^BAZ FILIO DEBUG "BIT ALREADY ZERO"\\. ^THE MONITOR
ATTEMPTED TO RETURN BLOCKS WHICH WERE ALREADY FREE.
^THIS HAPPENS WHEN A DAMAGED FILE IS DELETED.
.B 1;.I -30
^^BFO TAPUUO DEBUG "BETTER FIND ONE".\\ ^WHEN AN ATTEMPT WAS MADE
TO GENERATE THE TRANSFER LIST FOR READ BACKWARDS, THE END OF THE ORIGINAL TRANSFER LIST COULD
NOT BE FOUND.
.B 1;.I -30
^^BFU NETSER DEBUG "BUSY FOULED UP".\\ ^MORE THAN ONE BUFFER GOT ALLOCATED TO THE ^^DC75\\ OR ^^DAS85\\.
.B 1;.I -30
^^BMR FILUUO JOB "BLOCK MISSING FROM RIB".\\ ^A BLOCK
IN THE FILE WAS NOT POINTED TO BY THE ^^RIB\\.
.B 1;.I -30
^^BNF COMMON HALT "BOOTS NOT FOUND".\\
^^BOOTS\\ COULD NOT BE FOUND ON DISK.
.B 1;.I -30
^^BNR FILUUO JOB "BLOCK NOT IN RIB".\\ ^A POINTER WAS LOST FROM THE ^^RIB\\.
.B 1;.I -30
^^BNT FILFND DEBUG "BLOCK NOT THERE".\\ ^A CORE BLOCK (^A.^T. OR ^^UFB\\) WHICH WAS KNOWN TO EXIST COULD NOT BE FOUND.
.B 1;.I -30
^^BNZ CORE1 DEBUG "BIT NOT ZERO".\\ ^A CALL TO ^^CSETOS\\
ATTEMPTED TO SET A BIT WHICH WAS ALREADY ONE.
.B 1;.I -30
^^BPT FILFND JOB "BAD SEARCH LIST POINTER".\\ ^A SEARCH
LIST COULD NOT BE BUILT.
.B 1;.I -30
^^BRC COMCON DEBUG "BAD RETURN FROM CMPBIT".\\ ^WHEN THE FLAG BITS FOR THE DIRECTORY ENTRY WERE BEING COMPUTED,
A NONEXISTENT PAGE WAS FOUND.
.B 1;.I -30
^^BSN SEGCON STOP "BAD SEGMENT NUMBER".\\ ^THERE WAS A HIGH
SEGMENT NUMBER DISCREPANCY.
.B 1;.I -30
^^BSY XTCSER DEBUG\\ ^THE ^^DA28\\ INTERRUPTED WITH THE BUSY FLAG SET.
.B 1;.I -30
^^BTL SCNSER STOP "BACKWARD TTY LINK".\\ ^THE ^^TTY\\ BUFFER WAS LINKED IMPROPERLY CAUSING
THE ROUTINE TO WRITE OVER A PREVIOUSLY RECEIVED CHARACTER.
.B 1;.I -30
^^BWA FILIO JOB "BLOCK WENT AWAY".\\ ^A BLOCK THAT WAS ALLOCATED WAS NOT THERE ANYMORE.
.B 1;.I -30
^^C0P COMMON DEBUG "CPU0 PARITY".\\ ^ON ^^CPU0\\ THERE WAS A PARITY
ERROR WITH NO PARITY ERROR RECOVERY CODE, AN ^^I/O\\ PAGE FAILURE,
OR A TIMER TIME-OUT.
.B 1;.I -30
^^C1N CP1SER DEBUG "CPU1 NXM".\\
^NONEXISTENT MEMORY WAS ENCOUNTERED ON ^^CPU1\\.
.B 1;.I -30
^^C1P COMMON DEBUG "CPU1 PARITY".\\ ^ON ^^CPU1\\ THERE WAS
A PARITY ERROR WITH NO PARITY ERROR RECOVERY CODE, AN ^^I/O\\ PAGE FAILURE, OR A
TIMER TIME-OUT.
.B 1;.I -30
^^CAO FILUUO DEBUG "CLUSTER ADDRESS ODD".\\
^A CLUSTER ADDRESS COULD NOT BE CONVERTED TO A DISK BLOCK NUMBER.
.B 1;.I -30
^^CAS REFSTR HALT "COULDN'T ALLOCATE SPACE".\\ ^THE REFRESHER FILLED THE DISK.
.B 1;.I -30
^^CDD MSGSER JOB "CAN'T DISCONNECT DEVICE".\\ ^THE RELEASE
CALL ON ^^MPX\\ CALLED DISCONNECT AND DISCONNECT FAILED
WITH AN ILLEGAL FORMAT OR THE DEVICE NOT CONNECTED.
.B 1;.I -30
^^CFP CLOCK1 JOB "CAN'T FIND PDB".\\ ^^JBTPDB(J)=0\\ AT ^^SETR2\\
IN A MONITOR WHICH DOES NOT SWAP ^^PDB\\'S.
.B 1;.I -30
^^CGS ONCMOD HALT "CAN NOT GET STR".\\ ^THE ^^DESTROY\\
OPTION COULD NOT CREATE A STRUCTURE DATA BLOCK.
.B 1;.I -30
^^CIF FHXKON DEBUG "RC10 IS NOT FANCY".\\ ^AN ^^RP04\\
FUNCTION WAS ATTEMPTED ON AN ^^RC10\\ CONTROLLED DEVICE.
.B 1;.I -30
^^CIO REFSTR DEBUG "CFP IS ODD".\\ ^THE REFRESHER NOTICED
THE NUMBER OF BLOCKS PER CLUSTER DID NOT DIVIDE INTO THE
NUMBER OF BLOCKS PER SUPERCLUSTER.
.B 1;.I -30
^^CL0 SCNSER STOP "CHUNK LINK TO 0".\\ ^THE ^^TTY\\ CHUNKS
WERE MESSED UP.
.B 1;.I -30
^^CME FILFND DEBUG "CFP MODULO ERROR".\\ ^^CFP\\ DID
NOT START AT AN EVEN SUPERCLUSTER BOUNDARY.
.PG
.B1;.I-30
^^CMS VMSER DEBUG "CORE1 MUST SKIP". CORE1\\ GAVE A NONSKIP
RETURN WHEN ASKED FOR CORE IN USE.
.B 1;.I -30
^^CMU SEGCON STOP "CORE MESSED UP".\\ ^^CHKTAL\\ FOUND
THAT THE MONITOR'S CORE USAGE TABLES DID NOT CHECK WITH EACH OTHER.
.B 1;.I -30
^^CNA SCHED1 STOP "CORE NOT AVAILABLE".\\ ^THE CORE ALLOCATION
ROUTINE GAVE AN ERROR RETURN WHILE ATTEMPTING TO ALLOCATE
CORE FOR A SWAP-IN, AFTER IT HAD BEEN VERIFIED THAT ENOUGH CORE
WAS AVAILABLE.
.B 1;.I -30
^^CNE FILUUO DEBUG "CLUSTER NOT EVEN".\\ ^WHEN AN ATTEMPT WAS MADE
TO ALLOCATE INITIAL BLOCKS FOR A FILE, THE BLOCK WHICH WAS
COMPUTED AS THE START OF A SUPERCLUSTER DID NOT START AT AN
EVEN SUPERCLUSTER ADDRESS.
.B 1;.I -30
^^CRE TAPSER DEBUG "CANNOT RECOVER ERROR".\\ ^THE ERROR RECOVERY
PROCEDURE WAS CALLED WITH AN ^I/^O REQUEST BLOCK ALREADY MARKED NONRECOVERABLE.
.B1;.I-30
^^CRP CORE1 JOB "CANNOT RETURN PUSH DOWN LIST". GIVEPL\\
WAS CALLED AND THE PUSH DOWN LIST WOULD NOT FIT BACK INTO THE
JOB DATA AREA.
.B1;.I-30
^^CRW KILOCK STOP "CA RESOURCE WRONG".\\ ^THE ^C^A REQUEST WAS NOT
NEGATIVE. ^THE INTERLOCK ON THE ^^LOCK\\ CALL WAS NOT AVAILABLE, BUT
NO ONE WAS DOING A ^^LOCK\\ CALL.
.B1;.I-30
^^CSA COMCON DEBUG "CANNOT SET ACCESS ALLOWED".\\ ^DURING THE
SAVE OF AN ^^EXE\\ FILE A PAGE WAS PAGED IN BUT HAD ITS ACCESS
ALLOWED BIT OFF. ^AN ATTEMPT TO TURN THAT BIT ON FAILED
(VIRTUAL MEMORY MONITOR ONLY).
.B1;.I-30
^^CSE FILIO STOP "CHECKSUM ERROR".\\ ^THE WORD POINTED TO FOR
CHECKSUMMING WAS NOT IN THE USER'S ADDRESS SPACE.
.B1;.I-30
^^CWN NETSER DEBUG "CORE ALLOCATION WENT NEGATIVE". ^^NETSER\\
ATTEMPTED TO GIVE BACK MORE FREE CORE THAN IT HAD.
.B 1;.I -30
^^DBZ FILIO DEBUG "DEPLPC BIT ZERO".\\ ^THE LAST GROUP OF POINTERS FOR A FILE WAS NOT THE LAST GROUP IN THE ^^RIB\\.
.B 1;.I -30
^^DCR FILUUO DEBUG "DELRIB CPOPJ RETURN".\\ ^^DELRIB,\\ WHICH SHOULD
ALWAYS GIVE A SKIP RETURN,
DID NOT SKIP.
.B 1;.I -30
^^DDS FILUUO DEBUG "DELRIB DIDN'T SKIP".\\ ^^DELRIB\\, WHICH SHOULD
ALWAYS GIVE A SKIP RETURN, DID NOT SKIP.
.PG
.B 1;.I -30
^^DER FILUUO DEBUG "DELRIB RETURN ERROR".\\
^^DELRIB\\, WHICH SHOULD ALWAYS GIVE A SKIP RETURN, DID NOT SKIP.
.B1;.I-30
^^DFU NETSER DEBUG "DEVICE UNRECOGNIZED". UUOCON\\ CALLED
THE NETWORK SERVICE ROUTINE WITH A DEVICE NOT ON THE NETWORK.
.B 1;.I -30
^^DHA FILIO DEBUG "DON'T HAVE AU".\\ ^THE MONITOR ATTEMPTED
TO GIVE UP THE ^^AU\\ RESOURCE WHEN IT DID NOT HAVE IT.
.B 1;.I -30
^^DHB FILIO DEBUG "DON'T HAVE BUFFER".\\ ^THE BUFFER RETURN ROUTINE HAD NO BUFFER TO RETURN.
.B 1;.I -30
^^DHD FILIO DEBUG "DON'T HAVE DA".\\ ^THE MONITOR ATTEMPTED TO GIVE UP THE
^^DA\\ RESOURCE WHEN IT DID NOT HAVE IT.
.B 1;.I -30
^^DNF FILUUO DEBUG "DDB NOT FOUND".\\ ^NO PREDECESSOR DISK
DEVICE DATA BLOCK WAS FOUND WHEN AN ATTEMPT WAS MADE TO RETURN A ^^DDB\\.
.B 1;.I -30
^^DNR FILUUO DEBUG "DELRIB NONSKIP RETURN".\\
^^DELRIB\\, WHICH SHOULD ALWAYS GIVE A SKIP RETURN, DID NOT SKIP.
.B 1;.I -30
^^DNS FILUUO DEBUG "DELRIB NONSKIP RETURN".\\
^^DELRIB\\, WHICH SHOULD ALWAYS GIVE A SKIP RETURN, DID NOT SKIP.
.B 1;.I -30
^^DPL COMCON DEBUG "DIRECTORY PAGE LOST".\\ ^THE PAGE
THAT HAD TO BE WRITTEN OUT (NOT PAGED OUT) TO MAKE ROOM TO CREATE
THE DIRECTORY PAGE COULD NOT BE BROUGHT BACK IN (VIRTUAL MEMORY MONITOR ONLY).
.B1;.I-30
^^DPN COMCON DEBUG "DIRECTORY PAGE NONEXISTENT".\\ ^THE DIRECTORY
PAGE FOR AN ^^EXE\\ FILE WAS SUPPOSED TO BE DESTROYED, BUT IT COULD NOT BE (VIRTUAL MEMORY MONITOR ONLY).
.B1;.I-30
^^DPO SEGCON DEBUG "DIRECTORY PAGE OVERLAP".\\ ^ON A NONVIRTUAL
MEMORY SYSTEM ANOTHER ENTRY WAS BEING FETCHED FROM THE DIRECTORY
AND THE END OF THE PAGE WAS REACHED. ^HOWEVER, THERE IS A LIMIT
OF ONE PAGE ON A NONVIRTUAL MEMORY SYSTEM.
.B 1;.I -30
^^EPO ERRCON DEBUG "EXEC PDL OVERFLOW".\\ ^THE MONITOR'S
EXTENDED PUSHDOWN LIST OVERFLOWED.
.B 1;.I -30
^^ERB REFSTR DEBUG "ERROR READING BAT BLOCK".\\ ^THE REFRESHER COULD NOT READ THE ^^BAT\\ BLOCK.
.B 1;.I -30
^^ERD ONCMOD DEBUG "ERROR REFRESHING DISK".\\ ^^REFSTR\\
HAD AN ERROR REFRESHING A SPECIFIC STRUCTURE.
.B1;.I-30
^^ERF TAPSER STOP "ERROR RECOVERY FAILURE".\\
^DURING ERROR RECOVERY AN ^^IORB (I/O\\ REQUEST BLOCK) OTHER THAN
THIS CONTROLLER'S ERROR RECOVERY ^^IORB\\ WAS POSTED COMPLETE TO
THE ERROR RECOVERY PROCEDURE.
.B 1;.I -30
^^ERH REFSTR DEBUG "ERROR READING HOME.SYS".\\
^THE REFRESHER COULD NOT READ ^^HOME.SYS\\.
.B 1;.I -30
^^ERM ONCMOD DEBUG "ERROR READING MFD".\\ ^AN ERROR OCCURRED IN
TRYING TO READ THE ^M^F^D DURING ^^ONCE\\-ONLY.
.B 1;.I -30
^^ERP REFSTR HALT "EXTRA RETRIEVAL POINTER".\\ ^THE ^^HOME.SYS\\
^^RIB\\ FILLED UP WHILE THE DISK WAS BEING REFRESHED.
.B 1;.I -30
^^ERS ONCMOD DEBUG "ERROR READING SAT".\\ ^AN ERROR OCCURRED
WHILE READING THE ^^SAT\\ TABLE DURING ^^ONCE\\-ONLY.
.B1;.I-30
^^ESS FILFND JOB "EMPTY SYSTEM SEARCH LIST".\\
.B 1;.I -30
^^EUE ERRCON DEBUG "EXEC UUO ERROR".\\ ^THE MONITOR EXECUTED AN ILLEGAL ^^UUO\\ (CALL).
.B 1;.I -30
^^EWB REFSTR DEBUG "ERROR WRITING BLOCK".\\ ^THE REFRESHER
HAD AN ERROR WRITING A BLOCK.
.B 1;.I -30
^^EWH REFSTR DEBUG "ERROR WRITING HOME BLOCKS".\\
^THE REFRESHER COULD NOT WRITE HOME BLOCKS.
.B 1;.I -30
^^EWR ONCMOD DEBUG "ERROR WHILE REFRESHING".\\ ^THE REFRESHER HAD AN ERROR WHILE REFRESHING ALL THE
DISKS IN THE SYSTEM.
.B 1;.I -30
^^FAD FILUUO DEBUG "FILE ALREADY DORMANT".\\ ^AN ACCESS TABLE WAS FOUND TO BE DORMANT DURING A ^^CLOSE\\ CALL.
.B 1;.I -30
^^FDP FILIO DEBUG "FIXED-HEAD DEVICE POSITIONED".\\
^A POSITION DONE INTERRUPT WAS RECEIVED FROM A FIXED HEAD DEVICE.
^THIS MAY INDICATE A HARDWARE PROBLEM.
.B1;.I-30
^^FFU NETSER STOP "F FOULED UP".\\ ^AN ATTEMPT WAS MADE TO
PUT A JOB TO SLEEP, BUT THE JOB DID NOT EXIST.
.B 1;.I -30
^^FIP VMSER DEBUG "FREE PAGE IN USE".\\ ^WHEN
THE FREE CORE LIST WAS BEING SCANNED, A PAGE ALLOCATED TO A SEGMENT WAS ENCOUNTERED.
.B 1;.I -30
^^FLE SCNSER STOP "FREE LIST EMPTY".\\
^THE NUMBER OF FREE ^^TTY\\ CHUNKS DID NOT AGREE WITH THE
COUNT OF THE NUMBER OF FREE ^^TTY\\ CHUNKS.
.B 1;.I -30
^^FPF KILOCK STOP "PAGE ON FREE LIST IS NOT FREE".\\ ^A
PAGE ON THE FREE CORE LIST WAS LINKED TO A PAGE WHICH WAS NOT
ON THE FREE CORE LIST.
.B 1;.I -30
^^FPI KISER STOP "FREE##PAGE##IN#USE".\\##^A#PAGE#TAKEN#FROM
.I-30
^^KLSER\\ THE FREE LIST WAS NOT FREE.
.PG
.B1;.I-30
^^FPN KILOCK STOP "FREE PAGE NOT FOUND".\\ ^WHEN A PAGE
WAS BEING MOVED, A FREE PAGE IN ^^PAGTAB\\ WAS NOT ON THE FREE
CORE LIST.
.B 1;.I -30
^^FPZ SCNSER STOP "FREE POINTER ZERO".\\
^AN ATTEMPT WAS MADE TO PLACE A CHARACTER IN THE
^^TTY\\ BUFFER WHEN THE COUNT OF THE NUMBER OF FREE CHUNKS
WAS POSITIVE, BUT THE FREE LIST WAS EMPTY.
.B 1;.I -30
^^HBE REFSTR DEBUG "HOME BLOCK ERROR".\\ ^AN ERROR OCCURRED
DURING AN ATTEMPT TO READ THE HOME BLOCKS WHILE REFRESHING A FILE STRUCTURE.
.B 1;.I -30
^^HDS XTCSER STOP "HIBER DID NOT SKIP"\\. ^A CALL
TO THE ^^HIBER\\ SUBROUTINE DID NOT SKIP.
.B 1;.I -30
^^HIF FILIO DEBUG "HOLE IN FILE".\\ ^ALTHOUGH THE LAST
BLOCK IN THE FILE EXISTED, SOME BLOCK PRIOR TO THE LAST WAS MISSING.
.B 1;.I -30
^^HWU FILIO JOB "HARD WRONG UNIT".\\ ^THE WRONG UNIT
ON A DISK CONTROLLER INTERRUPTED. ^THIS IS
A HARDWARE PROBLEM.
.B 1;.I -30
^^IBI CLOCK1 JOB "INTERRUPT BLOCK ILLEGAL".\\
^AN INTERRUPT BLOCK WAS OUT OF BOUNDS IN PREPARATION FOR AN
INTERRUPT TO A JOB.
.B 1;.I -30
^^IBZ FILIO JOB "I/O TO BLOCK ZERO".\\ ^AN ATTEMPT WAS MADE TO READ
OR WRITE BLOCK ZERO. ^THE ONLY WAY BLOCK 0 CAN BE READ IS
BY READING ^^HOME.SYS[1,4]\\ OR USING THE ^^SUSET.\\ CALL.
^IF NEITHER CONDITION HOLDS, THERE IS A MONITOR ERROR.
.B 1;.I -30
^^ICC PSISER HALT "INVALID CONDITION CODE".\\ ^THE
CONDITION WHICH CAUSED THIS INTERRUPT DID NOT EXIST.
.B 1;.I -30
^^ICN SEGCON DEBUG "INCORE COUNT NEGATIVE".\\ ^WHEN
THE COUNT OF THE NUMBER OF JOBS IN CORE WHICH WERE
SHARING A HIGH SEGMENT WAS DECREMENTED, THE COUNT BECAME NEGATIVE.
.B 1;.I -30
^^ICW KALOCK DEBUG "IN CORE COUNT IS WRONG".\\ ^A HIGH
SEGMENT WAS IN THE WAY OF A JOB TO BE LOCKED, AND THE LOW SEGMENTS
ASSOCIATED WITH THE HIGH SEGMENT COULD NOT BE FOUND.
.B 1;.I -30
^^IDC ONCMOD HALT "IMPOSSIBLE DRUM CONDITION".\\
^THE NONEXISTENT "WRITE HEADER LOCKOUT" SWITCH FOR THE ^^RD10\\
WAS SET.
.B1;.I-30
^^IFI TAPSER STOP "ILLEGAL FUNCTION AT INTERRUPT LEVEL".\\
^AN ILLEGAL FUNCTION WAS FOUND IN AN ^^IORB (I/O\\ REQUEST BLOCK)
WHILE AT INTERRUPT LEVEL.
.B1;.I-30
^^IFU NETSER DEBUG "INTERRUPT FLAG UNRECOGNIZED". D85INT\\
CALLED ^^NETSER\\ WITH AN INVALID INTERRUPT.
.B 1;.I -30
^^IIP FILIO DEBUG "IO IN PROGRESS".\\ ^AN ATTEMPT WAS MADE TO START
A MONITOR READ OR WRITE ON A ^^DDB\\
WHICH WAS ^^IO\\ ACTIVE.
.B 1;.I -30
^^IME KISER DEBUG "ILL. MEM-REF FROM EXEC".\\ ^AN ^^EXEC\\ MODE
.I-30
^^KLSER\\ PAGE FAULT TOOK PLACE.
.B1;.I-30
^^INU TAPSER STOP "INTERRUPT ON NONEXISTENT UNIT". TAPSER\\
RECEIVED AN INTERRUPT TO SERVICE A NONEXISTENT UNIT.
.B 1;.I -30
^^IPF VMSER DEBUG "IN USE PAGE FREE\\". ^WHEN THE PAGES WHICH WERE
ALLOCATED TO A SEGMENT WERE BEING SCANNED, A PAGE ON THE FREE CORE
LIST WAS ENCOUNTERED.
.B 1;.I -30
^^IPM VMSER DEBUG "ILLEGAL POINTER IN MEMTAB".\\ ^AN
INCONSISTENCY WAS DETECTED IN THE SWAPPING DATA BASE.
.B1;.I-30
^^IPN VMSER DEBUG "IPCF PAGE NONEXISTENT".\\ ^AFTER ^^IPCF\\
PAGES WERE SWAPPED OUT, THEY WERE NOT FOUND IN THE SWAP LIST.
.B 1;.I -30
^^IRE KISER JOB "IOWD##RELOCATION##ERROR".\\##^FOLLOWING##A
.I-30
^^KLSER\\ JOB'S PAGING, AN ERROR OCCURRED IN CHANGING THE ^^IOWD\\ TO AN
ABSOLUTE ^^IOWD.\\
.B1;.I-30
^^ISS TX1KON DEBUG "IMPOSSIBLE STORED STATUS".\\ ^THE ^T^X01
GENERATED ^C^U STATUS WITHOUT DEVICE END FOR A UNIT BELIEVED TO BE
OFF-LINE. ^THIS SHOULD NEVER HAPPEN.
.B 1;.I -30
^^IUN FILUUO DEBUG "INVALID UNIT NUMBER".\\ ^^MFD RIB\\ FOR
A FILE STRUCTURE WAS ON AN INVALID UNIT.
.B 1;.I -30
^^JAC UUOCON DEBUG "JOB DATA AREA CLOBBERED".\\ ^^JOBHCU\\
WAS GREATER THAN 17.
.B 1;.I -30
^^JDJ ONCMOD DEBUG "JFFO DIDN'T JUMP".\\ ^LOGICAL UNIT NUMBER COULD NOT BE DETERMINED.
.B 1;.I -30
^^JIT SYSINI HALT "JOB##IN##TRANSIT".\\###^LOCK#WAS#NON-ZERO.
.B 1;.I -30
^^JNC FILIO DEBUG "JOB NOT IN CORE".\\ ^A JOB WHICH
HAD ACTIVE DISK ^I/^O WAS NOT IN CORE.
^THIS WAS DETECTED WHEN THE INTERRUPT TOOK PLACE.
.B1;.I-30
^^KAS TAPSER STOP "KONTROLLER ALREADY STARTED".\\ ^THE
CONTROLLER WAS BUSY WHEN ^^TAPSER\\ WAS READY TO START ^I/^O.
.B 1;.I -30
^^KDS DPXKON DEBUG "KONEC2 DIDN'T SKIP".\\ ^THE SUBROUTINE
^^KONEC2\\ SHOULD ALWAYS GIVE A SKIP RETURN.
.B 1;.I -30
^^KID SYSINI HALT "KONTROLLER IS DOWN".\\ ^A CONTROLLER WENT
DOWN DURING DISK INITIALIZATION.
.PG
.B 1;.I -30
^^KN1 CP1SER HALT "KT10A NOT ON CPU1".\\ ^^CPU1\\ DOES
NOT HAVE DUAL PROTECTION AND RELOCATION REGISTERS.
.B1;.I-30
^^KNF XTCSER STOP "KONTROLLER NOT FREE".\\ ^A REQUEST BY AN EXTERNAL
PROCESSOR WAS MADE AND RECOGNIZED BY THE ^^DA28C\\ BUT CONFLICTED
WITH THE CURRENT USE OF THE CONTROLLER.
.B 1;.I -30
^^KNS TAPSER STOP "KONTROLLER NOT SELECTED".\\ ^AN ATTEMPT WAS
MADE TO START ^I/^O ON A CONTROLLER THAT WAS NOT SELECTED.
.B1;.I-30
^^KOL TAPSER STOP "KONTROLLER OFF-LINE".\\ ^START ^I/^O WAS
CALLED ON A CONTROLLER THAT WAS OFF-LINE.
.B1;.I-30
^^LN1 ERRCON STOP "NO TTY LINE". T\\HE CONTROLLING TELETYPE
COULD NOT BE FOUND.
.B1;.I-30
^^LNP FILIO DEBUG "LAST POINTER NOT A POINTER". A\\N ALLOCATION
WAS DONE AND A ^^RIB\\ ERROR OCCURRED. ^WHEN AN ATTEMPT WAS MADE TO
DEALLOCATE THE SPACE, THE ^^RIB\\ POINTER WAS NOT VALID.
.B 1;.I -30
^^LNS SCNSER STOP "LINE NOT SETUP".\\ ^^RH(U)=0\\ ON THE CALL
TO ^^TSETBI\\.
.B1;.I-30
^^LNT ERRCON STOP "LDB (LINE) NOT THERE". T\\HE CONTROLLING TELETYPE
COULD NOT BE FOUND.
.B 1;.I -30
^^LPU FILUUO JOB "LAST POINTER UNIT-CHANGE".\\ ^A UNIT
CHANGE POINTER WAS THE LAST POINTER IN A ^^RIB\\, WHEN
A UNIT CHANGE POINTER SHOULD ALWAYS BE FOLLOWED BY A DATA POINTER.
.B1;.I-30
^^LTS NETSER DEBUG "LINK TO SELF". B\\UFFERS POINTED TO
THEMSELVES IN A LINKED LIST.
.B 1;.I -30
^^MAU CP1SER DEBUG "MASTER ALREADY UNLOCKED".\\
^^CPU0\\ ATTEMPTED TO GIVE UP (UNLOCK) THE ^^CPU\\ INTERLOCK, BUT
IT DID NOT OWN IT (HAVE IT LOCKED).
.B 1;.I -30
^^MCM METCON DEBUG "MCDB MISSING".\\ ^AFTER THE METERING OF A MONITOR
DATA POINT, AN ATTEMPT TO REMOVE A ^METER ^CHANNEL ^DATA ^BLOCK FAILED.
.B 1;.I -30
^^MCN FILFND DEBUG "MOUNT COUNT NEGATIVE".\\ ^THE MOUNT COUNT
ON A STRUCTURE WENT NEGATIVE.
.B 1;.I -30
^^MHB FILIO DEBUG "MUST HAVE BUFFER".\\ ^AN ATTEMPT WAS MADE TO READ A
^^RIB\\ INTO A MONITOR BUFFER WHEN THERE WAS NO MONITOR
BUFFER FOR THE JOB.
.B1;.I-30
^^MIW ONCE STOP "MEMORY INTERLEAVING WRONG". T\\HERE WAS A
MEMORY INTERLEAVING ERROR. ^THE OPERATOR MUST CORRECT THE PROBLEM.
.PG
.B 1;.I -30
^^MIZ VMSER DEBUG "MEMTAB IS ZERO".\\ ^AN INCONSISTENCY
WAS DETECTED IN THE SWAPPING DATA BASE.
.B1;.I-30
^^MMN ERRCON HALT "MONITOR MEMORY NONEXISTENT". A\\ MEMORY
DROPPED OFF-LINE, AND ONE OR MORE PAGES OF THE MONITOR WERE IN
NONEXISTENT MEMORY.
.B 1;.I -30
^^MMP ERRCON HALT "MONITOR MEMORY PARITY".\\ ^THE MONITOR
REFERENCED AN INSTRUCTION OR IMPORTANT DATA
WITH BAD PARITY.
.B1;.I-30
^^MMR KILOCK STOP "MOVING MONITOR PAGE NOT REQUIRED". T\\HE
EXPECTED NUMBER OF MONITOR PAGES TO BE MOVED COULD NOT BE MOVED,
BECAUSE THERE WERE NO FREE PAGES TO MOVE THEM TO.
.B1;.I-30
^^MNM SYSINI STOP "MONITOR IN NONEXISTENT MEMORY".\\
^THE MONITOR OVERLAPPED A PAGE OF CORE THAT WAS PREVIOUSLY
DETERMINED TO BE NONEXISTENT.
.B1;.I-30
^^MPN KILOCK STOP "MONITOR PAGE NOT FOUND". A\\ PAGE OF THE MONITOR
TO BE MOVED WAS NOT FOUND IN THE EXEC. PAGE MAP.
.B1;.I-30
^^MXM MSGSER JOB "MPX:#DDB MISSING".\\ ^THE ^D^D^B CHAIN
GOT MESSED UP; THE POINTER TO AN ^^MPX DDB\\ ON THE ^D^D^B CHAIN
WAS NOT RIGHT.
.B 1;.I -30
^^NAP FILUUO JOB "NOT ADDRESS POINTER".\\
^A RETRIEVAL POINTER DID NOT POINT TO A VALID DISK ADDRESS.
.B 1;.I -30
^^NCA CLOCK1 STOP "NO CORE ASSIGNED".\\ ^AN ATTEMPT WAS MADE TO
START A JOB WITH NO CORE MEMORY ASSIGNED.
.B 1;.I -30
^^NDA FILFND JOB "NO DUMMY ACCESS TABLE".\\
^THE ROUTINE TO REMOVE THE DUMMY ^A.^T. (^^TAKOU\\) COULD
NOT FIND THE BLOCK TO DELETE.
.B1;.I-30
^^NDC ONCMOD STOP "NO DF10C CODE". M\\ONITOR WAS NOT ASSEMBLED
FOR ^D^F10^C IN ^K^I MODE. ^SET SWITCH INSIDE CABINET DOOR TO ^K^A MODE.
.B 1;.I -30
^^NDJ SCNSER DEBUG "NO DDB FOR JOB".\\ ^A JOB'S ^^TTY
DDB\\ DID NOT EXIST. ^ALL JOBS (EVEN DETACHED JOBS) MUST HAVE A ^^DDB\\.
.B 1;.I -30
^^NDP CLOCK1 DEBUG "NOT DDB POINTER".\\ ^^WSYNC\\ WAS
CALLED WITH A STRANGE ADDRESS IN ^F.
.B 1;.I -30
^^NDS CLOCK1 STOP "NULL JOB DID SAVGET".\\ ^THE ^^MONSTR\\
ROUTINE WAS CALLED WHILE THE NULL JOB WAS RUNNING.
.B 1;.I -30
^^NED ONCE HALT "NO EXEC DDT".\\ ^^ONCE\\ DETERMINED THAT THERE WERE BREAKPOINTS
SET, BUT ^^EDDT\\ WAS NOT LOADED WITH THIS MONITOR.
.PG
.B 1;.I -30
^^NER FILUUO DEBUG "NO EXTENDED RIB".\\ ^THE POINTER TO
THE LAST BLOCK OF THE FILE WAS NOT IN THE ^^RIB\\ AND THERE
WAS NO EXTENDED ^^RIB\\. ^THIS HAPPENS WHEN A POINTER GETS LOST
FOR SOME REASON.
.B 1;.I -30
^^NEV UUOCON STOP "NO EVM". T\\HE ^^DDB\\ DID NOT HAVE EXEC. VIRTUAL MEMORY.
.B1;.I-30
^^NFC SCNSER STOP "NO FREE CORE".\\ ^ALL THE ^^TTY\\ CHUNKS
WERE USED UP.
^THIS CONDITION WAS CHECKED FOR EARLIER AND SPACE WAS AVAILABLE.
.B 1;.I -30
^^NFS VMSER DEBUG "NO FIRST SLOT".\\ ^AT THE START OF
A FRAGMENT, THE FIRST PHYSICAL PAGE OF THE FRAGMENT COULD NOT BE
FOUND IN THE PAGE MAP.
.B1;.I-30
^^NFU SYSINI DEBUG "NO FIRST UNIT". T\\HERE WAS NOT A FIRST UNIT
IN THE SYSTEM SEARCH LIST.
.B1;.I-30
^^NHF KALOCK STOP "NO HOLE FIT".\\ ^^HOLSRT\\ COULD NOT
FIND A HOLE FOR THIS JOB EVEN THOUGH ^^KALOCK\\ JUST CREATED ONE.
.B1;.I-30
^^NIV TAPUUO STOP "NULL INTERRUPT VECTOR ADDRESS". A\\N ^I/^O
REQUEST BLOCK WAS EXECUTED AND RETURNED TO ^^TAPUUO\\ WITH A ZERO
INTERRUPT VECTOR.
.B 1;.I -30
^^NMB FILIO DEBUG "NEED MONITOR BUFFER".\\
^AN ATTEMPT WAS MADE TO WRITE A ^^RIB\\ WITHOUT A MONITOR BUFFER TO WRITE IT FROM.
.B 1;.I -30
^^NMC ONCMOD HALT "NO MORE CORE".\\ ^^ONCE\\-ONLY FILLED UP CORE.
.B 1;.I -30
^^NMU REFSTR DEBUG "NO MORE UNITS".\\ ^THE REFRESHER WROTE A WRONG ^^RIB\\.
.B 1;.I -30
^^NNF FILUUO DEBUG "NMB NOT FOUND". ^^GETNMB\\ COULD NOT
FIND A NAME BLOCK. ^EITHER ^^DEVACC\\ OR ^^ACCNMB\\ WAS WRONG.
.B 1;.I -30
^^NNR FILUUO JOB "NO NEXT RIB".\\ ^DURING A ^^CLOSE\\ MONITOR CALL
THE LAST BLOCK OF THE FILE COULD NOT BE FOUND.
^THIS INDICATES THAT A DATA POINTER WAS LOST.
.B 1;.I -30
^^NNU ONCMOD DEBUG "NOT NEW UNIT".\\
^THE MONITOR EXPECTED TO FIND A NEW UNIT POINTER WHILE READING ^^SAT.SYS\\.
.B 1;.I -30
^^NOT SCNSER DEBUG "NO OPR TTY".\\ ^^DEVOPR=0\\.
.B 1;.I -30
^^NPC SCHED1 STOP "NO PDB IN CORE".\\ ^WHEN AN ATTEMPT WAS MADE TO
REQUEUE A JOB AND RESET ITS QUANTUM
RUN TIME, NO PROCESS
DATA BLOCK WAS FOUND FOR THAT JOB.
.B 1;.I -30
^^NPD FILIO DEBUG "NO POINTERS IN DDB".\\ ^AN EXTENDED ^^RIB\\
WAS NEEDED BECAUSE THE POINTERS IN THE ^^DDB\\ WERE EXHAUSTED, BUT THERE WERE NO POINTERS IN THE ^^DDB\\.
.B 1;.I -30
^^NPF KILOCK STOP "NEXT PAGE FREE".\\ ^THE MONITOR
ENCOUNTERED A FREE PAGE WHILE SEARCHING A SEGMENT'S PAGES
FOR THE TARGET PAGE.
.B 1;.I -30
^^NPJ DATMAN DEBUG "NO PDB FOR JOB".\\ ^A CALL TO
^^FNPDBS\\ DID NOT FIND A ^^PDB\\.
.B1;.I-30
^^NPN KASER STOP "NONEXISTENT# K/PAGE# NOT FREE\\". ^A ^K OR
.I-30
^^KISER\\ PAGE OF #NONEXISTENT #MEMORY BELONGED TO
.I -30
^^KLSER\\ EITHER THE MONITOR OR SOME JOB. ^THIS SHOULD ONLY HAPPEN IF THE
OPERATOR CONTINUES AFTER A ^N^X^M HALT.
.B 1;.I -30
^^NPP KISER STOP "NO PI IN PROGRESS".\\ ^CHANNEL 7 CODE WAS
.I-30
^^KLSER\\ CALLED FROM ^^UUO\\ LEVEL.
^THE PAGE TABLE COULD BE MESSED UP IF THIS WERE ALLOWED.
.B 1;.I -30
^^NPU ERRCON STOP "NULL PUSH-DOWN UNDERFLOW".\\
^THERE WERE MORE ^^POP\\'S ON THE NULL PUSHDOWN LIST THAN
MATCHING ^^PUSH\\'S.
.B1;.I-30
^^NRB TAPSER STOP "NO REQUEST BLOCK".\\ ^A DONE INTERRUPT
OCCURRED ON A CONTROLLER OR UNIT, AND NO REQUEST BLOCK WAS FOUND
CORRESPONDING TO THE INTERRUPT.
.B 1;.I -30
^^NRF VMSER DEBUG "SWPLST NOT REALLY FRAGMENTED".\\
^THERE WAS A POINTER TO A FRAGMENTED ^^SWPLST\\ ENTRY, BUT THE ENTRY
WAS NOT REALLY FRAGMENTED.
.B 1;.I -30
^^NRM FILUUO JOB "NEXT RIB MISSING".\\
^THERE WERE NOT ENOUGH POINTERS IN THE ^^RIB\\ TO ACCOUNT FOR
THE NUMBER OF BLOCKS WRITTEN, AND THERE WERE NO MORE ^^RIB\\'S.
.B 1;.I -30
^^NRS ONCMOD DEBUG "NO RIB IN SAT".\\ ^^SAT.SYS\\ HAD A
^^RIB\\ ERROR.
.B 1;.I -30
^^NSE VMSER DEBUG "NO SWPLST ENTRY".\\ ^WHEN AN ATTEMPT WAS MADE TO
COMPUTE THE UNIT AND BLOCK NUMBER REPRESENTED BY A ^^SWPLST\\
ENTRY, THE POINTER TO ^^SWPLST\\ POINTED TO A ZERO.
.B1;.I-30
^^NSL FILFND JOB "NO SUCH SEARCH LIST".\\ ^WHEN AN ATTEMPT
WAS MADE TO FIND THE SEARCH LIST POINTER FOR THE CURRENT
JOB, EITHER THE JOB NUMBER WAS 0, THERE WAS NO ^P^D^B, OR THE
SEARCH LIST WAS NULL.
.B 1;.I -30
^^NSR REFSTR HALT "NO SECOND RIB".\\ ^THE REFRESHER TRIED
TO CREATE A FILE WITH ONLY ONE ^^RIB\\.
.B 1;.I -30
^^NSS REFSTR DEBUG "NO SPACE FOR SAT".\\ ^THE REFRESHER
FILLED UP THE DISK.
.B 1;.I -30
^^NSU FILIO DEBUG "NO SUCH UNIT".\\ ^THE ^^RIB\\ OF A FILE
INDICATED A NONEXISTENT UNIT.
.B 1;.I -30
^^NUB FILFND JOB "NO UFD BLOCK".\\ ^THERE WAS NO ^^UFD\\
FOR A FILE EVEN THOUGH THE FILE EXISTED.
.B 1;.I -30
^^NUE FILUUO JOB "NO UFD ERROR".\\ ^THERE WAS NO ^^UFD\\
FOR A FILE BEING WRITTEN.
.B 1;.I -30
^^NUI XTCSER DEBUG "NONEXISTENT UNIT INTERRUPT."\\
^A UNIT WHICH WAS NOT KNOWN INTERRUPTED. ^THIS OCCURS WHEN THE
CONTENT OF THE FEATURE REGISTER IS WRONG DURING SYSTEM LOADING.
.B 1;.I -30
^^NUP FILUUO DEBUG "NO UNIT CHANGE POINTER".\\
^THE ^^RIB\\ DID NOT START WITH A UNIT CHANGE POINTER.
.B 1;.I -30
^^NUS VMSER DEBUG "NO UNIT FOR SWAPPING".\\ ^THERE WAS
NO UNIT IN THE ACTIVE SWAPPING LIST CORRESPONDING TO THE
UNIT INDICATED BY AN ENTRY IN ^^SWPLST\\.
.B1;.I-30
^^NWD FILIO DEBUG "NO WRITING DDB". FILIO\\ THOUGHT THERE
WERE MULTIPLE WRITERS AND HAD TO UPDATE THE ^D^D^B'S, BUT NO
WRITING ^D^D^B'S WERE FOUND.
.B 1;.I -30
^^NXU FILIO DEBUG "NONEXISTENT UNIT".\\ ^A UNIT CHANGE POINTER
POINTED TO A UNIT WHICH DOES NOT EXIST IN THIS STRUCTURE.
.B 1;.I -30
^^O1F VMSER DEBUG "ONLY ONE (1) FRAGMENT".\\
^SWAPPING SPACE WAS FRAGMENTED, BUT THERE WAS ONLY ONE ENTRY IN
THE FRAGMENT TABLE.
.B 1;.I -30
^^ONC FILUUO DEBUG "ODD NUMBERED CLUSTER".\\
^THE NUMBER OF BLOCKS ALLOCATED TO A FILE WAS NOT AN EVEN MULTIPLE
OF THE NUMBER OF CLUSTERS ALLOCATED.
.B1;.I-30
^^P2L VMSER STOP "PAGE TOO LOW".\\ ^AN ADDRESS IN THE USER'S
PAGE MAP WAS TOO LOW, I.E., IN THE MONITOR.
.B 1;.I -30
^^PAO COMCON STOP "PAGE ALREADY OUT\\". ^AFTER A PAGE
WAS PAGED OUT TO CREATE A DIRECTORY FOR AN ^^EXE\\ FILE, THE DIRECTORY
STILL COULD NOT BE CREATED.
.B 1;.I -30
^^PCN IPCSER DEBUG "PACKET COUNT NEGATIVE". T\\HE COUNT FOR
THE SYSTEM'S UNRECEIVED SENDS WENT NEGATIVE.
.B1;.I-30
^^PDA FILIO DEBUG "POINTERS WITH DIFFERENT ADDRESSES". A\\
POINTER WITHIN THE ^^RIB\\ AND MONITOR BUFFER DIFFERED.
.B 1;.I -30
^^PEW VMSER DEBUG "PAGTAB ENTRY WRONG".\\ ^WHEN THE PAGES
ALLOCATED TO A SEGMENT WERE BEING SCANNED, A PAGE ON THE FREE
CORE LIST WAS ENCOUNTERED.
.B 1;.I -30
^^PEZ KISER STOP "PAGPTR EQUALS ZERO".\\ #^THE# POINTER# TO
.I-30
^^KLSER\\ THE FREE CORE LIST WAS FOUND TO BE ZERO WHEN AN
ATTEMPT WAS MADE TO FIND A FREE PAGE.
.B 1;.I -30
^^PFA KILOCK STOP "PAGE FREE ALREADY".\\ ^THE MONITOR
ENCOUNTERED A FREE PAGE WHILE SEARCHING A SEGMENT'S PAGES FOR
THE TARGET PAGE.
.B 1;.I -30
^^PFC VMSER STOP "PAGE ON FREE CORE LIST".\\
^WHEN THE PAGES ALLOCATED TO A SEGMENT WERE BEING SCANNED,
A PAGE ON THE FREE CORE LIST WAS ENCOUNTERED.
.B1;.I-30
^^PGL COMCON STOP "PAGES GOT LOST". N\\O PAGES WERE FOUND
THAT COULD BE PAGED OUT TO MAKE ROOM FOR THE DIRECTORY OF AN
^^EXE\\ FILE (VIRTUAL MEMORY MONITOR ONLY).
.B 1;.I -30
^^PIE ERRCON STOP "PRIORITY INTERRUPT ERROR".\\
^A JUMP OCCURRED TO 40 + 2N +..., N=1,2,...7. ^THIS IS
CAUSED BY A DEVICE INTERRUPTING TO THE WRONG LOCATION.
.B 1;.I -30
^^PIF VMSER DEBUG "PAGE IS FREE".\\ ^WHEN THE
PAGES ALLOCATED TO A SEGMENT WERE BEING SCANNED, A PAGE ON THE
FREE CORE LIST WAS ENCOUNTERED.
.B 1;.I -30
^^PIN VMSER DEBUG "PAGE IN WORKING SET".\\
^A PAGE WHICH WAS VERIFIED TO NOT BE IN THE WORKING SET WAS IN IT.
.B 1;.I -30
^^PIP KISER DEBUG "PI#IN#PROGRESS".\\##^A#TRAP#TOOK##PLACE#AT
.I-30
^^KLSER PI\\-LEVEL, USUALLY PUSHDOWN LIST OVERFLOW.
.B 1;.I -30
^^PIW VMSER DEBUG "PAGE IS NOT IN WORKING SET".\\
^A PAGE WHICH HAD TO BE IN THE WORKING SET WAS NOT.
.B 1;.I -30
^^PJ0 CLOCK1 DEBUG "REQUEUE JOB 0".\\
^AN ATTEMPT WAS MADE TO REQUEUE JOB 0 (THE NULL JOB).
.B 1;.I -30
^^PLP FILIO DEBUG "PAST LAST POINTER".\\
^^SCNPTR\\ COULD NOT FIND A BLOCK WHICH SHOULD HAVE BEEN IN THE FILE.
.B 1;.I -30
^^PMU KISER STOP "PAGTAB#MESSED#UP".\\#
^THE TABLE USED##FOR
.I-30
^^KLSER\\ CORE ALLOCATION WAS NOT CORRECT.
.B1;.I-30
^^PNE FILIO DEBUG "POINTERS NOT EQUAL". A\\FTER THE POINTERS IN
THE ^^RIB\\ WERE UPDATED FROM THE ^D^D^B, A DISCREPANCY WAS
FOUND IN THE CLUSTER NUMBER.
.B 1;.I -30
^^PNM FILFND DEBUG "PHYSICAL NAME MISMATCH".\\ ^AFTER DETERMINING THAT A NAME REFERRED
TO A DISK UNIT, THE PHYSICAL NAME WAS LOST.
.B 1;.I -30
^^PNP KILOCK STOP "PAGE NOT PRESENT".\\
^THE DESTINATION COULD NOT BE FOUND IN THE FREE CORE LIST OR
IN THE PRESENT SEGMENT.
.B 1;.I -30
^^POP CLOCK1 DEBUG "PI ON PROGRESS".\\
^AN ^^APR\\ ERROR HAPPENED WHILE AT ^^PI\\ LEVEL. ^THIS WAS
EITHER A ^^NXM\\ (ANY PROCESSOR) OR A ^^PDL#OV\\ (^^KA10\\
ONLY). ^THE ^^KI10\\ OR ^^KL10\\ WILL STOP
WITH ^^IME\\ OR ^^PIP\\, AS WELL AS WITH THIS ^^STOPCD\\.
.B 1;.I -30
^^POR SEGCON STOP "PROCESS OUT OF RANGE".\\
^AN ATTEMPT WAS MADE TO ADD A HIGH SEGMENT TO THE ADDRESS SPACE
OF A NONEXISTENT JOB.
.B 1;.I -30
^^PQE FILIO DEBUG "POSITION QUEUE EMPTY".\\
^A DISK UNIT WAS IN POSITION WAIT STATE, BUT THERE WERE NO FILES
IN ITS QUEUE TO BE POSITIONED.
.B 1;.I -30
^^PSF KISER STOP "PAGE IN SEGMENT FREE".\\ ^WHEN SPACE# WAS
.I-30
^^KLSER\\ BEING ALLOCATED FOR THIS JOB, A PAGE ON THE FREE CORE LIST
WAS FOUND WITHIN THE JOB.
.B 1;.I -30
^^PTH KLSER HALT "PARITY TRAP HALT".\\ ^THERE WAS A HARD
EXEC. MODE PAGE FAIL TRAP AS A RESULT OF ^^AR\\ OR ^^ARX\\ PARITY.
.B 1;.I -30
^^PTP KLSER HALT "PAGE TABLE PARITY".\\
^THERE WAS A HARD PAGE FAIL TRAP AS A RESULT OF A PAGE TABLE PARITY ERROR.
.B 1;.I -30
^^PTT CORE1 JOB "PAST TOP OF TABLE".\\
^A CALL TO ^^SETZRS\\ ATTEMPTED TO ZERO MORE BITS THAN EXISTED.
.B1;.I-30
^^RBQ SCHED1 STOP "REQUEUING TO BEGINNING OF QUEUE".\\
^AN ATTEMPT WAS MADE TO REQUEUE TO THE BEGINNING OF A QUEUE WHICH
IS ALWAYS ILLEGAL IN THE 602 SCHEDULER.
.B 1;.I -30
^^RCC SCNSER STOP "RANGE CHECKED CHUNK".\\
^A CALL TO ^^TTPUTC\\ OR ^^TTGETC\\ SPECIFIED
A CHARACTER ADDRESS (IN ^T2) WHICH WAS NOT IN THE ^^TTY\\
BUFFER POOL. ^THIS IS SOMETIMES CAUSED BY ATTEMPTING
^^TTY\\ OUTPUT WITHOUT SETTING UP ^U TO POINT TO AN ^^LDB\\.
.B1;.I-30
^^RDP FSXKON DEBUG "RS04 DOES NOT POSITION". FILIO\\ TRIED
TO DO POSITIONING ON AN ^R^S04.
.B1;.I-30
^^RDS SEGCON STOP "REMAP DID NOT SKIP". M\\ONITOR WAS DOING
A REMAP AND AN ERROR OCCURRED.
.B 1;.I -30
^^REH ERRCON HALT "RECURSION IN ERROR HANDLER".\\
^^A STOPCD\\ WAS EXECUTED WHILE ^^STOPCD\\ RECOVERY WAS IN PROGRESS.
.B1;.I-30
^^RFU TAPSER STOP "RECOVERY FOULED UP". D\\URING ERROR
RECOVERY THE ^E^R^P (ERROR RECOVERY PROCEDURE) STATE WORD HAD AN
INVALID STATE NUMBER AT THE COMPLETION OF AN OPERATION.
.B1;.I-30
^^RIE XTCSER DEBUG "REMOTE INTERRUPT ERROR".\\ ^AN ERROR
OCCURRED DURING AN INTERRUPT FROM A REMOTE PROCESSOR.
.B 1;.I -30
^^RIF DPXKON DEBUG "RP10 IS NOT FANCY". A\\N ^R^P04 FUNCTION
WAS ATTEMPTED ON AN ^^RP\\10 CONTROLLED DEVICE.
.B 1;.I -30
^^RJZ SCHED1 STOP "REQUEUE JOB ZERO".\\
^A JOB WITH AN INVALID JOB NUMBER WAS BEING REQUEUED.
.B1;.I-30
^^RNA TAPSER STOP "REQUEST NOT ACTIVE". T\\HERE WAS A DONE
INTERRUPT, AND THE REQUEST BLOCK CORRESPONDING TO IT WAS NOT ACTIVE.
.B 1;.I -30
^^ROS SEGCON JOB "RAN OUT OF SEGMENTS".\\
^THERE WAS NO HIGH SEGMENT NUMBER AVAILABLE TO ADD A HIGH
SEGMENT TO A JOB'S ADDRESS SPACE. ^THIS SHOULD NOT HAPPEN,
BECAUSE THERE ARE ALWAYS AT LEAST AS MANY HIGH SEGMENT NUMBERS
AVAILABLE AS THERE ARE JOB NUMBERS AVAILABLE.
.B 1;.I -30
^^ROU ONCMOD HALT "RAN OUT OF UNITS".\\ ^WHEN AN ATTEMPT WAS MADE TO GET THE ADDRESS OF
THE NEXT DATA BLOCK IN THE STRUCTURE, THE POINTER INDICATED THE END
OF THE LIST.
.B 1;.I -30
^^RPM ONCMOD DEBUG "RETRIEVAL POINTER MISMATCH".\\
^THE UNIT CHANGE POINTER IN FILE ^^SAT.SYS\\ DID NOT POINT
TO THE NEXT UNIT IN THE FILE STRUCTURE.
.B 1;.I -30
^^S2L SWPSER STOP "SWAP TOO LOW".\\
^A SWAPPING REQUEST WOULD HAVE CLOBBERED PART OF THE MONITOR
(NONVIRTUAL MEMORY MONITOR ONLY).
.B 1;.I -30
^^SAC ERRCON DEBUG "STRANGE APR CONDITION".\\
^THE LOW PRIORITY ^^APR\\ SERVICE ROUTINE COULD NOT FIND ANY
ERRORS, THOUGH THE HIGH PRIORITY ^^APR\\ SERVICE ROUTINE SAID
AN ERROR TOOK PLACE.
.B 1;.I -30
^^SAU CP1SER DEBUG "SLAVE ALREADY UNLOCKED".\\
^^UNLOKS\\ WAS CALLED BUT THE INTERLOCK WAS NOT SET.
.B 1;.I -30
^^SBT FILUUO DEBUG "SHOULD NOT BE TRUNCATING".\\
^THE HIGHEST BLOCK NUMBER IN THE FILE WAS TOO SMALL.
.B 1;.I -30
^^SBW VMSER DEBUG "SWPLST BITS WRONG".\\
^AN ENTRY IN ^^SWPLST\\ SAID THAT BOTH
^I/^O WAS IN PROGRESS AND ^I/^O WAS DONE.
.B 1;.I -30
^^SCB XTCSER DEBUG "SPURIOUS CONI BITS".
A DA28C\\ INTERRUPT OCCURRED FOR NO VALID REASON.
.B 1;.I -30
^^SCO CP1SER HALT "SPLIT CYCLE ON".\\
^^CPU1\\ HAD:
.B1;.LM 34;.I -4
1.##^ADDRESS STOP SWITCH SET, OR
.B1;.I -4
2.##^FAST ^^AC\\'S TURNED OFF.
.PG;.LM 30;.TS 8,19,30;.I -30
^^SER FILUUO JOB "SETDDO ERROR RETURN".\\
^THERE WAS NO ROOM TO BUILD A ^^DDB\\ EVEN THOUGH ^^GET4WD\\ HAD JUST FOUND ROOM.
.B 1;.I -30
^^SFI FILUUO JOB "STR FREE-COUNT INCONSISTENT".\\
^THE STRUCTURE HAD FREE SPACE BUT NO UNITS WITHIN THE STRUCTURE HAD
FREE SPACE. ^THE SUM OF THE PARTS EXCEEDED THE WHOLE.
.B 1;.I -30
^^SFU FILIO DEBUG "SWAPPER FOULED UP".\\
^THE SWAPPER TRIED TO DO ^I/^O WITH A NONSWAPPING ^^DDB\\.
.B 1;.I -30
^^SIN VMSER DEBUG "SWPCNT IS NEGATIVE".\\
^THE COUNT OF THE NUMBER OF OUTSTANDING SWAPPING REQUESTS
WENT NEGATIVE WHEN AN ENTRY FROM ^^SWPLST\\ WAS BEING DELETED.
.B 1;.I -30
^^SLF VMSER DEBUG "SWPLST FULL".\\
^AN ENTRY COULD NOT BE MADE IN THE LIST BECAUSE THE ^^SWPLST\\
TABLE WAS FULL.
.B 1;.I -30
^^SLM FILUUO DEBUG "SEARCH LIST MISSING".\\
^^SETSRC\\ COULD NOT SET UP THE SEARCH LIST EVEN THOUGH IT COULD WHEN THE MONITOR CALL STARTED.
.B 1;.I -30
^^SLZ VMSER DEBUG "SLECNT IS ZERO".\\
^THE SUBROUTINE TO FIND AN ENTRY IN ^^SWPLST\\ WAS CALLED WHEN
THERE WERE NO ENTRIES IN ^^SWPLST\\.
.B 1;.I -30
^^SMU SCHED1 DEBUG "SWPCNT MESSED UP".\\
^THE COUNT OF THE NUMBER OF COMPLETED SWAPPING OPERATIONS WAS
POSITIVE, BUT NO COMPLETED SWAPPING REQUEST COULD BE FOUND (VIRTUAL
MEMORY MONITOR ONLY).
.B 1;.I -30
^^SNF KILOCK STOP "SEGMENT NOT FOUND".\\
^A PAGE WHICH WAS NOT ON THE FREE CORE LIST WAS NOT CONTAINED IN ANY SEGMENT'S ADDRESS SPACE.
.B 1;.I -30
^^SNI SWPSER DEBUG "SWAPPING NOT IN PROGRESS".\\
^^SPRCNT\\ (NUMBER OF SWAPS IN PROGRESS) WENT NEGATIVE (VIRTUAL MEMORY MONITOR ONLY).
.B 1;.I -30
^^SOD SCHED1 STOP "SPACE ON DISK".\\
^THE CALL TO ^^CORGET\\ IN ^^SWAPI\\ ASSIGNED SPACE ON THE DISK.
^THAT IS NOT ALLOWED ON A SWAP-IN.
.B 1;.I -30
^^SOR ERRCON STOP "SEGMENT OUT OF RANGE".\\
^THE SEGMENT NUMBER IN ^^AC##J\\ WAS LARGER THAN THE MAXIMUM
SEGMENT NUMBER IN THE SYSTEM.
.B 1;.I -30
^^SPM FILUUO JOB "SECOND POINTER MISSING".\\
^THE POINTER TO THE SECOND ^^RIB\\ WAS MISSING FROM THE FIRST ^^RIB\\.
.B 1;.I -30
^^SRE ONCMOD DEBUG "SAT READ ERROR".\\
^^ONCE\\-ONLY HAD AN ERROR READING THE ^^SAT\\ TABLE.
.PG;.I -30
^^SRO SWPSER DEBUG "SPACE RAN OUT".\\
^^VIRTAL\\ WAS POSITIVE, BUT NO SWAPPING UNIT HAD ANY ROOM ON IT.
.B 1;.I -30
^^SSD SWPSER STOP "SWAP SPACE DISAPPEARED".\\
^THE COUNT OF THE NUMBER OF WORDS OF SWAPPING SPACE FREE SHOWED
MORE SPACE THAN THE ^^SAT\\ TABLE FOR SWAPPING.
.B1;.I-30
^^SSM TX1KON STOP "STORED STATUS MISSING". W\\HEN THE ^D^X10
SHOULD HAVE STORED EXTENDED STATUS, IT DID NOT.
.B 1;.I -30
^^SSO KILOCK STOP "SEGMENT SWAPPED OUT".\\
^A HIGH SEGMENT WHICH WAS NEITHER DORMANT NOR IDLE HAD NO LOW
SEGMENT IN CORE SHARING IT.
.B1;.I-30
^^SWJ VMSER DEBUG "SWAPPED IN WRONG JOB".\\ ^THE JOB NUMBER
OF THE JOB JUST SWAPPED IN DID NOT MATCH THE JOB NUMBER IN THE ^^UPMP\\.
.B 1;.I -30
^^SWN SWPSER DEBUG "SQREQ WENT NEGATIVE".\\
^^SWPSER\\ GOT TO ^^SWPINT\\ WHEN THE SWAPPER THOUGHT NOTHING
WAS HAPPENING (VIRTUAL MEMORY MONITOR ONLY).
.B 1;.I -30
^^TC0 XTCSER DEBUG\\ ^WORK ENTRIES WHICH WERE QUEUED WHEN
THE ^^DA28C\\ WAS BUSY WERE NOT EXECUTED.
.B 1;.I -30
^^TC1 XTCSER STOP\\ ^THE ^^LIPS\\ PROTOCOL STATUS WAS WRONG
WHEN AN ^^I/O\\ TRANSFER STARTED.
.B 1;.I -30
^^TC2 XTCSER DEBUG\\ ^A REMOTE PROCESSOR INTERRUPT OCCURRED
WHEN THE CONTROL WAS NOT IDLE, I.E., IN USE BY SOFTWARE.
.B 1;.I -30
^^TC3 XTCSER DEBUG\\ ^THE ACCOUNTING FOR PSEUDO-ACTIVE TASKS
IN THE CONTROL DATA BLOCK WAS WRONG.
.B 1;.I -30
^^TC4 XTCSER DEBUG\\ ^THE ACCOUNTING FOR PSEUDO-ACTIVE TASKS
IN A UNIT CONTROL BLOCK WAS WRONG.
.B 1;.I -30
^^TC5 XTCSER DEBUG\\ ^THE ACCOUNTING FOR PSEUDO-ACTIVE TASKS
IN A UNIT CONTROL BLOCK WAS WRONG.
.B 1;.I -30
^^TC6 XTCSER DEBUG\\ ^THE ACCOUNTING FOR PSEUDO-ACTIVE TASKS
IN THE CONTROL DATA BLOCK WAS WRONG.
.B 1;.I -30
^^TC7 XTCSER STOP\\ ^A JOB THAT WAS TRYING TO GRAB THE ^^DA28C\\
CONTROL OBTAINED IT, BUT THE CONTROL WAS NOT FREE ACCORDING TO
THE CONTROL DATA BLOCK.
.B 1;.I -30
^^TCI FILUUO DEBUG "TRUNCATION CHECK INCONSISTENT".\\
^A RENAME WHICH WAS CAUSING TRUNCATION ATTEMPTED TO TRUNCATE
TOO MANY BLOCKS EVEN THOUGH THAT WAS ALREADY CHECKED.
.B 1;.I -30
^^TMP FILIO DEBUG "TOO MANY POINTERS".\\
^THERE WERE MORE RETRIEVAL POINTERS THAN WOULD FIT IN A ^^RIB\\.
^THERE IS A COUNTER (^^DEVRSU\\) TO PREVENT THIS FROM HAPPENING.
.B 1;.I -30
^^TMR REFSTR HALT "TOO MANY RETRIEVAL POINTERS".\\
^THE ^^SAT.SYS RIB\\ FILLED UP DURING A REFRESH.
.B 1;.I -30
^^TMU ONCMOD HALT "TOO MANY UNITS".\\ ^AFTER THE LAST UNIT WAS RETRIEVED,
ADDITIONAL DATA BLOCKS WERE POINTED TO.
.B 1;.I -30
^^TOW CP1SER HALT "TRAP OFFSET WRONG".
^T\\HE ^^CPU1\\ INTERRUPT VECTOR WAS IN THE SAME PLACE AS THE
^^CPU0\\ INTERRUPT VECTOR.
.B1;.I-30
^^UAS TAPSER STOP "UNIT ALREADY STARTED". T\\HE UNIT WAS
ALREADY DOING ^I/^O WHEN ^^TAPSER\\ WAS READY TO START ^I/^O.
.B 1;.I -30
^^UDE FILIO DEBUG "UNIT DOESN'T EXIST".\\
^A UNIT CHANGE POINTER POINTED OFF INTO NEVER-NEVER LAND.
.B 1;.I -30
^^UDM FILUUO JOB "UFD DATA MISSING".\\
^THE CORE TABLES INDICATED THAT THE ^^UFD\\ WAS LONGER THAN IT REALLY WAS.
.B 1;.I -30
^^UFI FILUUO DEBUG "UNIT FREE-COUNT INCONSISTENT".\\
^NO FREE SPACE WAS FOUND ON A UNIT EVEN THOUGH THE FREE-COUNT WAS POSITIVE.
.B 1;.I -30
^^UIF ONCMOD HALT "UNIT IN FILE STRUCTURE".\\
^THE TABLES WHICH DRIVE ^^ONCE\\-ONLY'S '^^DESTROY\\' OPTION DUPLICATED
A UNIT.
.B 1;.I -30
^^UIL ERRCON STOP "UUO AT INTERRUPT LEVEL".\\
^AN INTERRUPT SERVICE ROUTINE EXECUTED AN ILLEGAL MONITOR CALL.
.B1;.I-30
^^UIP XTCSER DEBUG "NOT ^A UNIQUE INTERRUPT"\\. ^TWO DIFFERENT
TYPES OF USAGE WERE DEFINED FOR THE ^^DA28C\\ CONTROL.
.B 1;.I -30
^^UNF FILUUO DEBUG "UFB NOT FOUND". A\\ RENAME WAS DONE ACROSS
^U^F^D'S AND THE ^U^F^B WAS NOT FOUND.
.B 1;.I -30
^^UNJ COMMON DEBUG "UUO FROM NULL JOB".\\ ^THE NULL JOB EXECUTED A MONITOR CALL OTHER
THAN THE DOORBELL MONITOR CALL.
.B1;.I-30
^^UNL VMSER DEBUG "UPMP NOT LAST". T\\HE ^^UPMP\\ WAS NOT THE
LAST PAGE SWAPPED OUT.
.B1;.I-30
^^UNS TAPSER STOP "UNIT NOT SELECTED". A\\ UNIT WAS NOT
SELECTED WHEN ^^TAPSER\\ WAS READY TO START ^I/^O.
.B 1;.I -30
^^UPC FILUUO JOB "UNIT CHANGE POINTER CLOBBERED".\\ ^THE POINTER TO A UNIT OF
A ^^RIB\\ WAS LOST DURING ^^RIB\\ DEFINITION.
.B 1;.I -30
^^UPI FILIO DEBUG "UNIT POINTER ILLEGAL".\\
^AN ATTEMPT WAS MADE TO CREATE AN EXTENDED ^^RIB\\
ON A NONEXISTENT UNIT.
.B 1;.I -30
^^UWS VMSER DEBUG "UNIT WRONG STATE". O\\N A HUNG SWAPPING
DEVICE THE ^U^D^B INDICATED AN UNEXPECTED STATE.
.B1;.I-30
^^WAD VMSER DEBUG "WSBTBL AND AABTBL DISCREPANCY".\\
^AN ACCESS PAGE FAULT OCCURRED FOR A PAGE WHICH SHOULD HAVE HAD THE
ACCESS ALLOWED BIT ON IN THE PAGE MAP.
.B 1;.I -30
^^XTH SCHED1 DEBUG "XJOB TOO HIGH".\\
^THE COUNT OF THE NUMBER OF JOBS WHICH MUST BE SWAPPED OUT
AND BACK IN TO SATISFY A CORE EXPANSION REQUEST WAS POSITIVE,
BUT NO EXPANDING JOB COULD BE FOUND.
.B 1;.I -30
^^ZBC REFSTR DEBUG "ZERO BLOCKS PER CLUSTER".\\
^THE REFRESHER WAS CALLED WITH ^^HOMBPC=0\\.
.B 3