Trailing-Edge
-
PDP-10 Archives
-
scratch
-
10,7/unscsp/bootdx/bootdx.mac
There are 7 other files named bootdx.mac in the archive. Click here to see a list.
TITLE BOOTDX TO BOOTSTRAP THE MICRO HIDDEN IN THE DX10 OR DX20
SUBTTL T.HESS/TAH/EGF/TW/GMU 23-AUG-79
.TEXT "/SEG:LOW REL:HELPER"
;COPYRIGHT (C) 1974,1975,1976,1977,1978,1979 BY
;DIGITAL EQUIPMENT CORPORATION, MAYNARD, MASS.
;
;
;THIS SOFTWARE IS FURNISHED UNDER A LICENSE AND MAY BE USED AND COPIED
;ONLY IN ACCORDANCE WITH THE TERMS OF SUCH LICENSE AND WITH THE
;INCLUSION OF THE ABOVE COPYRIGHT NOTICE. THIS SOFTWARE OR ANY OTHER
;COPIES THEREOF MAY NOT BE PROVIDED OR OTHERWISE MADE AVAILABLE TO ANY
;OTHER PERSON. NO TITLE TO AND OWNERSHIP OF THE SOFTWARE IS HEREBY
;TRANSFERRED.
;
;THE INFORMATION IN THIS SOFTWARE IS SUBJECT TO CHANGE WITHOUT NOTICE
;AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY DIGITAL EQUIPMENT
;CORPORATION.
;
;DIGITAL ASSUMES NO RESPONSIBILITY FOR THE USE OR RELIABILITY OF ITS
;SOFTWARE ON EQUIPMENT WHICH IS NOT SUPPLIED BY DIGITAL.
.EDTR==0 ;LAST EDITOR
.MAJV==3 ;MAJOR VERSION #
.MINV==1 ;MINOR VERSION
.EDIT==24 ;EDIT #
%%BTDX==BYTE (3).EDTR(9).MAJV(6).MINV(18).EDIT
;PROGRAM WHICH BOOTSTRAPS AND DUMPS PDP-8A'S INSIDE THE
;DX10 PROGRAMMABLE DATA CHANNEL.
; OR BOOTS AND DUMPS THE MICRO-PROCESSOR INSIDE THE DX20
;LOAD INSTRUCTIONS
; .LOAD BOOTDX.MAC, %"SEG:LOW" REL:HELPER.REL
; Edit history:
;
; 22 BCM 10-Oct-80 SPR #10-29970
; put in check for existence of DX10
; 23 BCM 4-May-81 SPR #10-
; move the check for edit 22, 3 lines down
; 24 SMW 9-4-84
; Ignore KLIPA's and KLINI's, they aren't really RH20's
;
LOC 137
%%BTDX
RELOC
SALL
;PERMANANT REGISTER ASSIGNMENT
;MACRO TO GENERATE CODE FOR SETTING UP T2,T3 FOR WTREG/WTRGX
DEFINE PREWT(X)
<SETZ T2, ;;SET T2 TO 0
MOVEI T3,X ;;GET REGISTER NUMBER IN T3
>;END OF PREWT
;MISCELLANEOUS DEFINITION
PDLTH=20 ;STACK DEPTH FOR SUBROUTINE CALLS
BUFLEN=^D20 ;BUFFER LENGTH FOR OPERATOR COMMAND
;MAGIC ADR AND VALUE DEFINITION
MAGICA==11 ;ADDRESS THAT THE STANDALONE AND
; USER MODE BOOTSTRAPS MUST PUT A
; MAGIC VALUE IN AS THE MONITOR CHECKS
; THE MAGIC VALUE DURING INITIALIZATION.
MAGICV==42562 ;THE MAGIC VALUE
;RH20 CONI/CONO BITS
;CONI (RH)
CI.BPE==1B18 ;DATA BUS PARITY ERROR
CI.EXC==1B19 ;EXCEPTION
CI.LWE==1B20 ;LONG WORD COUNT ERROR
CI.SWE==1B21 ;SHORT WORD COUNT ERROR
CI.MBE==1B22 ;MBOX ERROR
CI.DRE==1B23 ;DRIVE RESPONSE ERROR
CI.RAE==1B24 ;REGISTER ACCESS ERROR
CI.MBH==1B25 ;MBOX HALTED
CI.OVR==1B26 ;DATA OVERRUN
CI.MEN==1B27 ;MASSBUS ENABLE
CI.ATN==1B28 ;DRIVE ATTENTION
CI.2RF==1B29 ;SECONDARY COMMAND REGISTER FULL
CI.ATE==1B30 ;ATTENTION EBABLE
CI.1RF==1B31 ;PRIMARY COMMAND REGISTER FULL
CI.DON==1B32 ;CHANNEL DONE
CI.PIA==7 ;PRIORITY ASSIGNMENT
CI.ERR==555000 ;BITS THAT CAUSE ERRORS
;CONO
CO.RAE==1B24 ;CLEAR REGISTER ACCESS ERROR
CO.RST==1B25 ;CONTROLLER RESET
CO.XFR==1B26 ;CLEAR TRANSFER ERROR
CO.MEN==1B27 ;MASSBUS ENABLE
CO.RCL==1B28 ;RESET MBOX COMMAND LIST POINTER
CO.DEL==1B29 ;DELETE SECONDARY COMMAN
CO.ATE==1B30 ;ENABLE ATTENTION INTERRUPTS
CO.STP==1B31 ;STOP CURRENT COMMAND
CO.DON==1B32 ;CLEAR DONE
CO.CLR==005010 ;CLEAR BITS THAT CAUSE INTERRUPTS
SUBTTL PARAMETERS
;DX20 REGISTERS
DXCTR==0 ;CONTROL REGISTER
DXSTR==1 ;STATUS REGISTER
DXERR==2 ;ERROR REGISTER
DXMTR==3 ;MAINTENNANCE REGISTER
DXASR==4 ;ATTENTION SUMMARY REGISTER
DXDTR==6 ;DRIVE TYPE AND HARDWARE VERSION REG.
DXDR0==30 ;DIAGNOSTIC REGISTER
; IR FOR MICROPROCESSOR
DXDR1==31 ;DIAGNOSTIC REGISTER
DXDR5==35 ;DIAGNOSTIC REGISTER 5
DXDR7==37 ;DIAGNOSTIC REGISTER 7
;DXMTR BITS & FIELDS
MP.SC==1B31 ;SINGLE CYCLE
WR.EP==1B32 ;WRITE SINGLE PARITY
MP.STA==1B33 ;MP START
DX.RST==1B34 ;BIT FOR RESET DX20
;DXDR1 BITS & FIELDS
IR.EN==1B20 ;ENABLE IR LOAD FROM MICRO-STORE
MS.EN==1B21 ;ENABLE MICRO-STORE LOAD FROM IR
PC.EN==1B22 ;ALLOW LOAD/WRITE OF PC
PC.AI==1B23 ;ENABLE PC AUTO-INCREMENTING
DX.PC=7777B35 ;MASK FOR THE PC
;DXDR7 BITS & FIELDS
IR.PER==1B22 ;IR PARITY ERROR
;COMMON DATAO BITS & FIELDS
DO.RS: POINT 6,T2,5 ;REGISTER SELECT FIELD
DO.LR==1B6 ;LOAD REGISTER ENABLE
DO.DRE==1B9 ;DISABLE RAE STOP
;COMMON DATAI BITS
DI.CPE==1B8 ;CONTROL BUS PARITY ERROR
DI.TRA==1B10 ;TRA (MASSBUS SIGNAL)
;MASS BUS DEVICE TYPES
TY.RP4==020 ;RP04 DRIVE TYPE
TY.RS4==001 ;RS04 DRIVE TYPE
TY.TML==010 ;LOWEST TM02 TYPE
TY.TMH==017 ;HIGHEST TM02 TYPE
TY.DX2==60 ;DX20/TX02 DRIVE TYPE***(=050060)
; VERSION # IS 100****(100017)
TY.RP2==61 ;DX20/RP20 DRIVE TYPE (010061)
; UCODE VERSION 200
;FIELD DEFINITION FOR DX20 REGISTERS
DT.TYP: POINT 9,T1,35 ;DRIVE-TYPE FIELD IN REGISTER
ED.NUM: POINT 10,Q1,35 ;EDIT NUMBER
VR.NUM: POINT 6,Q1,25 ;VERSION NUMBER
SUBTTL DEFINITIONS
;DEVICE CODES
PDC==220 ;FIRST DX10
PDC2==224 ;2ND DX10
;DX10 CONO AND CONI BITS
RUNIND==(1B17) ;RUN INDICATOR
MPERR==1B26 ;MICRO-PROCESSOR ERROR
CLRERR==001700 ;CLEARS ALL ERRORS
PIMASK==774007 ;MASK FOR INFO TO SAVE
;DX10 REGISTER SELECTION CODES
RSEL==(1B17) ;SELECT REGISTER
MPCTL==4 ;CONTROLL AND MEMORY DATA
MPADR==5 ;ADDRESS
FR==14 ;FEATURE REGISTER
;BITS IN CTL REGISTER
MPSS==1B18 ;SINGLE STEP SWITCH
MPHALT==1B19 ;HALT SWITCH
MPCONT==1B20 ;CONTINUE SWITCH
ENEXM==1B22 ;ENABLE EXAMINE
ENDEP==1B23 ;ENABLE DEPOSIT
DXCLR==1B16 ;DX10 MASTER CLEAR
HLTINS==7402 ;PDP-8 HALT INSTR
;DEFINITIONS FROM C.MAC
SP.CR0==1 ;RUN ON CPU0 ONLY
.STCPU==14 ;SET CPU SPECIFICATION
;USELESS MACROS
DEFINE TELLCR (STRING)<
OUTSTR [ASCIZ \" STRING
\]
>
DEFINE WARNCR (STRING)<
OUTSTR [ASCIZ \% STRING
\]
>
DEFINE ERROR (STRING)<
XLIST
JRST [OUTSTR [ASCIZ \? STRING
\]
JRST EXITX]
LIST>
DEFINE USEROR (STRING)<
XLIST
JRST [OUTSTR [ASCIZ \? STRING
\]
JRST STARTE]
LIST>
DEFINE RETURN <
XLIST
POPJ P,
LIST>
;PARAMETERS
CHI==1 ;INPUT CHANNEL
CHIMOD==10 ;INPUT MODE (IMAGE)
CHXMOD==0 ;INPUT MODE OF A8 FILE
CHO==2 ;OUTPUT CHANNEL FOR DUMPS
CHOMOD==0 ;OUTPUT MODE (ASCII)
PDSIZ==20 ;PDL SIZE
;AC'S
F==0
T1=1
T2=2
T3=3
T4=4
P1=5
P2=6
P3=7
P4=10
WC==11 ;WORD COUNT FOR A8 FILES
RHNUM=12 ;THE RH20 NUMBER \ KEEP
DRVNUM=13 ;THE DRIVE NUMBER FOR THE RH20 / TOGETHER
Q1=14
Q2=15
W=16 ;PNTR TO IOWD BASE
CX==16
P=17 ;PUSH DOWN PNTR
;BITS IN F
DR.CHK==1B35 ;CHECKING FOR A DX20
DXFND==1B34 ;FOUND 1 DX20 ALREADY
IFNDEF V.CLR,<V.CLR==7777> ;END OF AREA TO CLEAR
IFNDEF V.DUMP,<V.DUMP==0> ;START OF DUMP
IFNDEF V.END,<V.END==7777> ;END OF AREA TO DUMP+1
IFNDEF V.TYPE,<V.TYPE==TY.DX2> ;DEFAULT DRIVE TYPE
IFNDEF V.STRT,<V.STRT==200> ;START ADDRS
IFNDEF V.DX2T,<V.DX2T==TX2OFS> ;DEFAULT OFFSET INTO TABLES OF TYPE
;OF CONTROLLER ON DX20 IF NO TYPE IS
;EXPLICITLY GIVEN (TX02)
IFNDEF V.DFLT,<V.DFLT==-1> ;SET TO -1 IF /DX10 IS TO BE THE
;DEFAULT SWITCH, 0 IF /DX20 IS TO
;BE THE DEFAULT
SUBTTL LOAD PROGRAM
STARTE: CLRBFI ;CLEAR TTY INPUT IF ERROR
START: RESET
SETZB F,FWAZER ;CLEAR STORAGE
MOVE T1,[FWAZER,,FWAZER+1]
BLT T1,LWAZER
SETOM FWAONE ;PRESET SWITCH ANSWERS TO -1
MOVE T1,[FWAONE,,FWAONE+1]
BLT T1,LWAONE
START2: JSP T2,[MOVE P,[IOWD PDSIZ,PDLST]
MOVEI T1,TTOCH
MOVEM T1,OCHLOC ;SET UP TTY OUTPUT
JRST @T2]
PUSHJ P,GETCOM ;GO GET COMMAND
JUMPL RHNUM,START3
PUSHJ P,SETCPU ;SET CPU ONLY ON CPU SPECIFIED
MOVEI T1,CCINT ;SET UP ^C INTERCEPT
HRRM T1,.JBINT## ;SAVE IN CORRECT PLACE
SETZB T1,CCINTP ;ZAP
TRPSET T1, ;GET GOOD PRIVS
ERROR <TRPSET failed>
SKIPGE DRVNUM ;UNIT SPECIFIED?
PUSHJ P,LOKDX ;NO, FIND THE DEFAULT
PUSHJ P,TESDSW ;MAKE SURE WE HAVE A VALID DX20
SETOM A.CHL ;MAKE LATER CODE HAPPY
;FALL INTO NEXT PAGE
START3: RESET ;RECLAIM SPACE IF RE-STARTING
XCT START2 ;SET UP PUSH DOWN LIST
MOVEI W,PDCBAS ;ASSUME CHL 0
SKIPGE T1,A.CHL ;USER SPECIFIED?
JRST START4 ;NO - USE DEFAULT
CAILE T1,1 ;IN RANGE?
USEROR Illegal DX10 channel number
MOVE W,[PDCBAS
PDC2BS](T1)
START4: SKIPE NODEF ;DID USER SPECIFY SWITCHES?
JRST STRT4A ;YES (S)HE DID...
MOVEI T1,V.STRT ;USE /START AS THE DEFAULT
MOVEM T1,A.STRT ;SET UP DEFAULT VALUE
JRST STRT4B ;JUMP OVER SWITCH CHECK
STRT4A: SETZM NODEF ;CLEAR DEFAULT SWITCH
SKIPGE A.DUMP ;SEE IF /DUMP
SKIPL A.END ;OR IF /END
JRST DODUMP ;GO DO DUMP
SKIPL A.STRT ;SEE IF /START
SKIPGE A.LOAD ;AND /LOAD
JRST .+2 ;NO--OK
USEROR Can't do both /LOAD and /START
SKIPL A.CLR ;SEE IF /CLEAR
JRST [SKIPGE A.LOAD ;YES--SEE IF /LOAD
SKIPL A.STRT ; OR /START
JRST .+1 ;YES--DO BOTH
JRST STRTLD] ;NO--GO START 11
STRT4B: SKIPN T2,DEV ;IS DEVICE NULL
MOVSI T2,'SYS' ;YES - THEN USE SYS
MOVEI T1,CHXMOD ;SET UP MODE
MOVEI T3,INHDR ;POINT TO RING HEADER
OPEN CHI,T1 ;OPEN CHL
USEROR Can't OPEN the input device
;;;; FALIN TO NEXT PAGE
JUMPL RHNUM,START5
MOVE T2,A.DX20 ;GET TYPE OF DX20
MOVE T2,FILTAB(T2) ;GET DEFAULT FILENAME FOR CONTROLLER
MOVSI T3,'ADX'
JRST START6
START5: MOVE T2,['DXMPA '] ;DEFAULT FOR DX10 IS DXMPA.A8
MOVSI T3,'A8 '
START6: SKIPN T1,NAME ;GET FILE NAME
MOVE T1,T2 ;USE DEFAULT
SKIPN T2,EXT ;EXTENSION
MOVE T2,T3
TRZ T2,-1 ;CLEAR NULL FLAG
RELOOK: MOVEI T3,0 ;CLEAR WORD
MOVE T4,DIRECT ;GET DIRECTORY
DMOVEM T1,FILNAM ;SAVE NAME FOR VERIFY
LOOKUP CHI,T1 ;LOOKUP FILE
JRST LUKAGN ;SEE IF MORE TRIES
INBUF CHI,0 ;DEFAULT BUFFERS
STRTLD: PUSHJ P,RESET8 ;GO RESET '8
SKIPGE A.CLR ;SEE IF /CLEAR
JRST [MOVEI T1,V.CLR ;NO - DO DEFAULT
MOVEM T1,A.CLR
JRST .+1]
PUSHJ P,CLEAR ;TRY TO CLEAR '8
SKIPGE VERERR
ERROR <Error while clearing memory.>
SKIPGE A.LOAD ;WANT TO LOAD
SKIPL A.STRT ; OR START
SKIPA ;YES - GO ON
JRST [PUSHJ P,RESTOR ;NO - JUST /CLEAR I GUESS
JRST START] ;RESTART
SETZM VERERR ;CLEAR VERIFY ERROR FLAG
JUMPGE RHNUM,LOAD20
TELLCR DX10 loading
MOVE T1,[MEM8,,MEM8+1]
MOVE T2,[BYTE (12)HLTINS,HLTINS,HLTINS]
MOVEM T2,MEM8 ;INIT TO ALL HALTS
BLT T1,MEM8+^D4096/3
PUSHJ P,CHKLFT ;SEE WHAT TYPE OF FILE
SKIPE A8FLG ;BIN OR A8
JRST STRTA8 ;A8 - START LOADING
JRST STRTL1 ;BIN - LOAD IT
LUKAGN: SKIPE EXT ;CHECK ARG
JRST LUKERR
CAMN T2,[SIXBIT /A8/] ;FIRST DEFAULT
JRST [MOVSI T2,'BIN' ;TRY .BIN
JRST RELOOK]
TLZE T2,-1 ;DEFAULT OR NULL
JUMPE T2,RELOOK ;TRY NULL
LUKERR: USEROR LOOKUP failed
STRTL1: PUSHJ P,GETBYT ;GET A BYTE
JUMPE P1,STRTL1 ;SKIP ZEROES
CAIE P1,200 ;VALID LEADER?
ERROR <Cannot find leader>
STRTL2: PUSHJ P,GETWRD ;FETCH WORD
CAIN P1,20000 ;IS THIS LEADER
JRST STRTL2 ;YES - SKIP IT
TRZN P1,10000 ;CHECK FOR ADDRESS
ERROR <First word not an address>
SETZM CHKSUM ;CLEAR CKSUM & FLAG
SETZM VERERR ;...
SETZM BINFLG ;BIN/RIM TAPE FLAG
LDBINA: PUSHJ P,LOADA ;GET ADDRESS
ADDM P2,CHKSUM ;ADD TO CHECKSUM
PUSHJ P,GETWRD ;GET NEXT WORD
LOAD1: CAIN P1,20000 ;TRAILER?
JRST LOADV ;YES - GO VERIFY
TRZE P1,10000 ;ADDRESS?
JRST LDBINA ;YES - HANDLE IT
PUSH P,P2 ;SAVE PARTIAL CKSUM
PUSH P,P1 ;SAVE WORD
PUSHJ P,GETWRD ;PEEK AHEAD
TRNN P1,30000 ;2ND DATA WORD?
SETOM BINFLG ;YES - SAY ITS A BIN TAPE
TRNN P1,20000 ;TRAILER?
JRST LDBINW ;NO - LOAD IT
SKIPGE BINFLG ;BIN/RIM?
JRST LDBINC ;BIN TAPE CHECK CHECKSUM
LDBINW: EXCH P1,0(P) ;SAVE P1 GET WORD
PUSHJ P,LOADW ;LOAD IT
MOVE T1,-1(P) ;RESTORE CHECKSUM
ADDM T1,CHKSUM ;ACCUMULATE
POP P,P1 ;RESTORE P1
POP P,T1 ;PRUNE PDL
JRST LOAD1 ;LOOP BACK FOR MORE
;HERE TO CHECK CKSUM FOR BINARY FORMAT TAPES
LDBINC: POP P,P1 ;THIS MUST BE THE CKSUM
POP P,P2 ;CLEAN PDL
MOVE T1,CHKSUM ;GET OUR CHECKSUM
ANDI T1,7777 ;TRIM TO 12 BITS
ANDI P1,7777 ;LIKEWISE FILE COPY
CAME P1,T1 ;TA-DA
ERROR <Checksum does not match>
;HERE TO VERIFY CORE IMAGE
LOADV: MOVEI P1,0 ;INITIAL ADDRESS
MOVE P2,[POINT 12,MEM8] ;POINT TO INTERNAL COPY
PUSHJ P,EXAM8 ;SET FOR SUPER-EXAMINE
JRST LOADV1 ;T1 HAS CONTENTS
JRST LDDONE ;ALL DONE - DO WRAP UP
LOADV1: ILDB P1,P2 ;GET COPY
CAMN P1,T1 ;???
JRST LOADV2 ;SO FAR SO GOOD
PUSH P,T1 ;SAVE WHAT WE SAW
SETOM VERERR ;SAY WE LOST
OUTSTR [ASCIZ /? Verify error at /]
MOVE T1,ADDRES ;TELL HIM WHERE
PUSHJ P,L4OCT
OUTSTR [ASCIZ / ,has /]
POP P,T1 ;GET IT BACK
PUSHJ P,L4OCT ;TELL THE BAD NEWS
OUTSTR [ASCIZ / ,should have /]
MOVE T1,P1 ;REAL STUFF
PUSHJ P,L4OCT ;SORRY 'BOUT THAT
OUTSTR [BYTE (7)15,12] ;CRLF
LOADV2: AOS T1,ADDRES ;ADVANCE TO NEXT LOC
CAIG T1,7777 ;FINISHED?
RSKP:
CPOPJ1: AOS 0(P) ;SAY GO ON
POPJ P, ;CRAZY WAY OUT
;ALL DONE CHECK ERRORS AND START '8 IF NECESSARY
LDDONE: SKIPE VERERR ;SEE IF OK
ERROR <Verify error>
PUSHJ P,LMAJIK ;LOAD CONST
PUSHJ P,FETCNF ;GET CONFIG INFO
SKIPGE P2,A.STRT ;LOOK FOR STARTING ADDRS
MOVE P2,A.LOAD ;...
SKIPG P2 ;ONE SPECIFIED?
MOVEI P2,V.STRT ;USE DEFAULT
SKIPL A.LOAD ;LOAD ONLY?
MOVEI P2,0 ;YEP
SKIPE P2 ;SHOULD WE START IT
PUSHJ P,START8 ;YES - TRY TO
SKIPN P2 ;GIVE CORRECT MESSAGE
TELLCR DX10 loaded.
SKIPE P2
TELLCR DX10 started.
CLOSE CHI, ;TERMINATE INPUT CHL
RELEAS CHI,
PUSHJ P,PNTCNF ;PRINT CONFIG INFO
JRST GOHOME ;WHEW
;ROUTINE TO LOAD ADDRESS IN P1 INTO ADRS REG
LOADA: MOVEM P1,ADDRES ;SAVE ADDRESS
MOVE T1,[RSEL,,MPADR]
XCT PDCDTO(W) ;SELECT ADRS REG
MOVE T1,ADDRES
XCT PDCDTO(W) ;LOAD ADDRESS
PUSH P,P2 ;DON'T CLOBBER P2
IDIVI P1,3 ;COMPUTE ADDRS INTO MEM8
ADD P1,MPNTR(P2) ;GET B.P.
MOVEM P1,APNTR ;SAVE IT
POP P,P2
POPJ P, ;RETURN
;ROUTINE TO LOAD PDP-8 WORD IN P1
LOADW: MOVE T1,[RSEL,,MPCTL]
XCT PDCDTO(W) ;SELECT CONTROL REG
MOVE T1,P1 ;GET WORD
IORI T1,ENDEP ;ENABLE DEP
XCT PDCDTO(W) ;DEPOSIT WORD IN MEM
MOVE T1,P1 ;GET WORD AGAIN
IDPB T1,APNTR ;STASH IN MEM8
AOS T1,ADDRES ;INCR ADDRESS
CAIE T1,10000 ;DON'T CHECK THIS
PUSHJ P,CKCPMA ;CHECK HDWRE ALSO AND EXIT
POPJ P, ;RETURN
;ROUTINE TO LOAD A8 FILES
STRTA8: SETZM CHKSUM ;CLEAR THIS
SETZM VERERR
LDA8WC: PUSHJ P,WCREAD ;GET WORD COUNT IN WC
JUMPE P1,LOADV ;DONE IF ZERO
MOVE WC,P1
PUSHJ P,WDREAD ;GET DATA WORD
PUSHJ P,LOADA ;LOAD ADDRESS
LDA8D: PUSHJ P,WDREAD ;GET WORD
MOVE T1,P1 ;SET UP DATA WORD
PUSHJ P,LOADW ;LOAD IT
SOJG WC,LDA8D ;LOOP THROUGH ALL WORDS
PUSHJ P,CHREAD ;READ AND VERIFY CHECKSUM
JRST LDA8WC ;GET NEXT RECORD
;ROUTINE TO READ THE CHECKSUM FROM FILE AND THE CRLF
;CHECK THAT CHECKSUM IS CORRECT
CHREAD: PUSHJ P,GET2W ;GET A WORD
CAIE P2,15 ;TERMINATOR BETTER BE CR
ERROR <End-of-line missing>
ADD P1,CHKSUM ;ADD COMPUTED CHECKSUM
ANDI P1,7777 ;CHECKIT
JUMPN P1,[ERROR <Checksums do not agree>]
PUSHJ P,GETC ;GET LF
CAIE P1,12 ;DOUBLE CHECK CRLF
ERROR <End-of-line missing>
POPJ P, ;RETURN
;ROUTINE TO DO MEMORY EXAMINES
;P1 HAS ADDRS TO START AT
;RETURN WITH CPOPJ TO STOP CYCLE/ CPOPJ1 TO DO NEXT EXAMINE
EXAM8: MOVE T1,[RSEL,,MPADR]
XCT PDCDTO(W) ;SELECT ADDRS REG
MOVE T1,P1 ;STARTING ADDRESS
XCT PDCDTO(W) ;SET IT
MOVEM P1,ADDRES ;SAVE ADDRS
EXAM8N: MOVE T1,[RSEL,,MPCTL]
XCT PDCDTO(W) ;SELECT CONTROLL
MOVEI T1,ENEXM ;ENABLE EXAMINE
XCT PDCDTO(W) ;...
XCT PDCDTI(W) ;READ CONTENTS
ANDI T1,7777 ;JUST THE CONTENTS
PUSHJ P,@0(P) ;CALL CALLER
JRST CPOPJ1 ;HE IS THROUGH
MOVE T1,ADDRES ;GET INCREMENTED ADDRES
PUSHJ P,CKCPMA ;CHECK AUTO INCR
JRST EXAM8N ;GET NEXT ITEM
FETCNF: MOVE T1,[RSEL,,FR]
XCT PDCDTO(W) ;FEATURE REGISTER
XCT PDCDTI(W) ;READ IT
MOVEM T1,FEATUR ;FEATURES?
MOVEI P1,3 ;READ LOCATION 3
PUSHJ P,EXAM8 ;...
POPJ P,
MOVEM T1,VERMP ;VERSION #
AOS P1,ADDRES ;NEXT LOC
PUSHJ P,EXAM8 ;DO IT THE HARD WAY
POPJ P, ;THIS IS WIERD
MOVEM T1,EDTMP ;SAVE EDIT #
POPJ P, ;RETURN
LMAJIK: MOVE T1,[RSEL,,MPADR]
XCT PDCDTO(W) ;SELECT ADDRS
MOVEI T1,17 ;SECRET LOC
XCT PDCDTO(W) ;...
MOVE T1,[RSEL,,MPCTL]
XCT PDCDTO(W) ;SELECT CTL REG
MOVEI T1,4756!ENDEP ;THIS IS IT FOLKS!!!!
XCT PDCDTO(W) ;MAJIK NOW LOADER
POPJ P, ;RETURN
SUBTTL DUMP PROGRAM
DODUMP: SKIPL RHNUM ;THIS A DX20?
USEROR <Can't /DUMP a DX20>
SKIPGE A.LOAD ;SEE IF /LOAD
SKIPL A.STRT ;OR IF /START
USEROR Can't /LOAD and /DUMP at the same time
SKIPL A.CLR ;SEE IF /CLEAR
USEROR Can't /CLEAR and /DUMP at the same time
MOVEI T1,CHOMOD ;SET OUTPUT MODE
SKIPN T2,DEV ;GET DEVICE
MOVSI T2,'DSK' ;DEFAULT TO DISK
MOVSI T3,OUTHDR ;POINT TO BUFFER HEADER
OPEN CHO,T1 ;OPEN FILE
USEROR Can't OPEN the output device
SKIPN T1,NAME ;GET FILE NAME
MOVE T1,['DXMPA '] ;USE DEFAULT
SKIPN T2,EXT ;GET EXTENSION
HRLZI T2,'LSD' ;DEFAULT
TRZ T2,-1 ;CLEAR NULL FLAG
MOVEI T3,0 ;CLEAR PROTECTION, ETC.
MOVE T4,DIRECT ;GET DIRECTORY
ENTER CHO,T1 ;ENTER FILE
USEROR ENTER failed
OUTBUF CHO,0 ;SET DEFAULT BUFFERS
;ACCUMULATE HEADING DATA
STRTDM: MOVE T1,[POINT 7,HEADER]
MOVEM T1,HEDPNT ;INIT POINTER FOR HEADER MSG
PUSHJ P,HEDTXT
ASCIZ /DX-10 #/
MOVE T1,A.CHL ;CHL NUMBER
PUSHJ P,HEDDIG ; AND PRINT
PUSHJ P,HEDTXT
ASCIZ / dump by BOOTDX /
LDB T1,[POINT 9,.JBVER##,11]
PUSHJ P,HEDOCT ;PRINT VERSION NUMBER
LDB T1,[POINT 6,.JBVER##,17] ;GET MINOR VERSION #
JUMPE T1,DMHDV1 ;JUMP IF NONE
SUBI T1,1 ;FAKE OUT DIVIDE
IDIVI T1,^D26 ;GET LAST LETTER
JUMPE T1,DMHDV0 ;JUMP IF ONLY 1 LETTER
ADDI T1,"A"-1 ;CONVERT 1ST LETTER
PUSHJ P,HEDCHR
DMHDV0: MOVEI T1,"A"(T2)
PUSHJ P,HEDCHR ;OUTPUT LAST LETTER
DMHDV1: HRRZ T1,.JBVER## ;GET EDIT NUMBER
JUMPE T1,DMHDV2 ;JUMP IF ZERO
MOVEI T1,"("
PUSHJ P,HEDCHR
HRRZ T1,.JBVER##
PUSHJ P,HEDOCT
MOVEI T1,")"
PUSHJ P,HEDCHR ;FINISH "(EDIT NUMBER)"
DMHDV2: LDB T1,[POINT 3,.JBVER##,2] ;GET "WHO MADE EDIT"
JUMPE T1,DMHDV3 ;JUMP IF DIGITAL DID
MOVEI T1,"-"
PUSHJ P,HEDCHR
XCT DMHDV2 ;GET "WHO" BACK
PUSHJ P,HEDDIG ; AND PRINT
DMHDV3: MOVEI T1,11 ;HORIZONTAL TAB
PUSHJ P,HEDCHR
MSTIME T1, ;GET TIME OF DAY (MILLESECONDS)
IDIVI T1,^D60000 ;GET MINUTES
IDIVI T1,^D60 ;GET HOURS
PUSH P,T2 ;SAVE REMAINDER AS MINUTES
PUSHJ P,HEDDEC ;PRINT QUOTIENT AS HOURS
MOVEI T1,":"
PUSHJ P,HEDCHR ;PRINT COLON
POP P,T1 ;GET MINUTES BACK
PUSHJ P,HEDDEC ; AND PRINT
MOVEI T1,11
PUSHJ P,HEDCHR ;PRINT TAB
DATE T1,
IDIVI T1,^D31*^D12 ;YEAR GOES TO T1
ADDI T1,^D64 ;ADD IN BASE YEAR
IDIVI T2,^D31 ;T2 GETS MONTH, T3 GETS DAY
PUSH P,T1 ;SAVE YEAR
PUSH P,[ASCII /-Jan-/
ASCII /-Feb-/
ASCII /-Mar-/
ASCII /-Apr-/
ASCII /-May-/
ASCII /-Jun-/
ASCII /-Jul-/
ASCII /-Aug-/
ASCII /-Sep-/
ASCII /-Oct-/
ASCII /-Nov-/
ASCII /-Dec-/](T2)
MOVEI T1,1(T3) ;GET DAY
PUSHJ P,HEDDEC ; AND PRINT
POP P,T1 ;GET MONTH
PUSHJ P,HED7 ; AND PRINT
POP P,T1
PUSHJ P,HEDDEC ;PRINT YEAR
MOVE T1,[20,,11] ;GET SYSTEM
GETTAB T1, ; SERIAL NUMBER
MOVEI T1,0 ;UNKNOWN
SKIPLE T1 ;SEE IF OK
CAILE T1,^D9999
JRST DMHDV5 ;SYSTEM NUMBER BAD
PUSH P,T1 ;SAVE NUMBER
PUSHJ P,HEDTXT
ASCIZ / System /
POP P,T1
PUSHJ P,HEDDEC ;PRINT SYSTEM NUMBER
DMHDV5: MOVSI T1,(ASCII / /)
PUSHJ P,HED7 ;PRINT SPACES
MOVSI T4,-5 ;SET HEADER COUNT
DMHDV6: MOVEI T1,11 ;POINT TO TABLE
HRL T1,T4 ;POINT TO ENTRY
GETTAB T1, ;GET SYSTEM HEADER LINE
MOVEI T1,0 ;UNKNOWN
PUSHJ P,HED7 ;PRINT TEXT
AOBJN T4,DMHDV6 ;LOOP UNTIL DONE
MOVEI T1,0
PUSHJ P,HEDCHR ;STUFF NULL IN AT END OF HEADER
PUSHJ P,LHEAD ;GO LIST HEADER
PUSHJ P,RESET8 ;GRONK THE '8
TELLCR DX10 dumping
PUSHJ P,FETCNF ;GET CONFIG INFO
PUSHJ P,PNTCNF ;PRINT MICRO-CODE VER # ON TTY
MOVEI T1,LCHAR ;SET UP PRINTER FOR LIST OUTPUT
MOVEM T1,OCHLOC ;...
MOVEI T1,[ASCIZ "Micro-code version: "]
PUSHJ P,LSTTX ;DUMP TO LISTING
MOVE T1,VERMP
PUSHJ P,LOCT
MOVEI T1,"("
PUSHJ P,LCHAR ;PRINT CHAR
MOVE T1,EDTMP
PUSHJ P,LOCT
MOVEI T1,[ASCIZ ") ECO: "]
PUSHJ P,LSTTX
LDB T1,[POINT 7,FEATUR,26]
PUSHJ P,LOCT
MOVEI T1,[ASCIZ " SER: "]
PUSHJ P,LSTTX
LDB T1,[POINT 9,FEATUR,35]
PUSHJ P,LOCT
PUSHJ P,LCRLF2
MOVEI T1,[ASCIZ "IBUS Registers"]
PUSHJ P,LSTTX
PUSHJ P,LCRLF2
MOVEI P1,17 ;ALL SIXTEEN
MOVSI P2,RSEL ;SET UP DATAO WORD
RSELUP: HRRZ T1,P2 ;REGISTER
PUSHJ P,LOCT
PUSHJ P,LSLSH ;PRINT SLASH TAB
MOVE T1,P2
XCT PDCDTO(W) ;SELECT REG
XCT PDCDTI(W) ;READ IT
PUSHJ P,L6OCT ;PRINT SIX OCTAL DIGITS
TRNN P1,3 ;MOD 4 CRLFS
JRST [PUSHJ P,LCRLF2
JRST RSLUP1]
PUSHJ P,LTAB
PUSHJ P,LTAB
RSLUP1: ADDI P2,1 ;ADVANCE TO NEXT
SOJGE P1,RSELUP ;LOOP TILL DONE
;NOW FETCH MEMORY FROM '8
SKIPGE P1,A.DUMP ;GET STARTING ADDRESS
MOVEI P1,V.DUMP ;DEFAULT
MOVEM P1,A.DUMP
SKIPGE P4,A.END ;ENDING LOC
MOVEI P4,V.END ;DEFAULT
MOVE P3,[POINT 12,MEM8]
PUSHJ P,EXAM8 ;START DUMPING
JRST [IDPB T1,P3 ;STORE WORD
AOS T1,ADDRES ;ADVANCE TO NEXT LOC
CAMG T1,P4 ;DONE?
AOS (P)
POPJ P,] ;RETURN - TO SELF
;NOW DUMP TO LISTING
MOVE P3,[POINT 12,MEM8]
MOVE T1,A.DUMP ;GET START ADDRS
MOVEM T1,ADDRES ;SAVE IT
DLUP: PUSHJ P,L4OCT ;PRINT ADDRS
PUSHJ P,LSLSH ;SLASH AND TAB
ILDB P1,P3 ;GET CONTENTS
MOVE T1,P1 ;PRINT OCTAL
PUSHJ P,L4OCT
PUSHJ P,LTAB ;TAB
PUSHJ P,PNTINS ;PRINT INSTR IN SYMBOLIC
AOS T1,ADDRES ;ADVANCE TO NEXT
CAMG T1,P4 ;DONE?
JRST DLUP ;NO - LOOP
CLOSE CHO, ;YES - CLOSE FILE
RELEAS CHO,
JRST GOHOME ;DONE
;ROUTINE TO PRINT A SYMBOLIC INSTRUCTION
;C(P1) := INSTR
;PRESERVE P3,P4
PNTINS: PUSH P,[0] ;MARK STACK
JUMPE P1,[PUSH P,['...']
JRST PNTDMP]
LDB T1,[POINT 3,P1,26]
CAIG T1,5 ;LOOK AT OP CODE
JRST PNTNRM ;DO NORMAL ROUTINE
CAIN T1,6 ;IOT?
JRST PNTIOT ;YES - SPECIAL
;OP = 7 DO SPECIAL HACK
CAIN P1,7000
JRST [PUSH P,['NOP']
JRST PNTDMP]
TRNN P1,400 ;GROUP 1?
JRST PNTG1 ;YES
TRNN P1,1 ;GROUP 2?
JRST PNTG2 ;YES
TRNE P1,200 ;GROUP 3
PUSH P,['CLA'] ;SEE IF CLA BIT ON
CAIN P1,7621 ;CHECK SPECIAL HACKS
JRST [MOVEI T2,'CAM'
MOVEM T2,0(P)
JRST PNTDMP]
CAIN P1,7521
JRST [PUSH P,['SWP']
JRST PNTDMP] ;GO DUMP
TRNE P1,20
PUSH P,['MQL']
TRNE P1,100
PUSH P,['MQA']
PNTXXX: SKIPN 0(P) ;ANYTHING?
PUSH P,['***']
JRST PNTDMP ;DUMP LIST
;PRINT GROUP 1 OPR INSTRS
PNTG1: TRNE P1,200 ;CHECK CLA BIT
PUSH P,['CLA']
TRNE P1,100
PUSH P,['CLL']
TRNE P1,1
PUSH P,['IAC']
TRNE P1,40
PUSH P,['CMA']
TRNE P1,20
PUSH P,['CML']
LSH P1,-1 ;NOW GET ROTATE INFO
ANDI P1,7 ;ONLY
JUMPE P1,PNTXXX ;GO DUMP IF NONE
PUSH P,RTAB(P1) ;ELSE GET FROM TABLE
JRST PNTXXX ;AND THEN DUMP
;HERE TO DO GROUP 2 OPR
PNTG2: TRNE P1,10 ;SLIGHTLY STRANGE
JRST PNTG2A
TRNE P1,100
PUSH P,['SMA']
TRNE P1,40
PUSH P,['SZA']
TRNE P1,20
PUSH P,['SNL']
JRST PNTG2B
PNTG2A: TRNE P1,100
PUSH P,['SPA']
TRNE P1,40
PUSH P,['SNA']
TRNE P1,20
PUSH P,['SZL']
PNTG2B: TRNE P1,200
PUSH P,['CLA']
CAIN P1,7410 ;SPECIAL GROUP 2 OPRS
PUSH P,['SKP']
CAIN P1,7404
PUSH P,['OSR']
CAIN P1,7402
PUSH P,['HLT']
JRST PNTXXX
;HERE TO PRINT NORMAL OP-CODES (0-5)
PNTNRM: PUSH P,ITAB(T1)
TRNE P1,400 ;LOOK FOR INDIRECT
PUSH P,['I']
TRNN P1,200
PUSH P,['0'] ;NOT PAGE 0 BIT
MOVE T1,P1 ;MAKE COPY OF INSTR
ANDI T1,177 ;GET ADDRS PART
MOVE T2,ADDRES ;SEE WHAT PAGE WE ARE ON
ANDI T2,7600 ;PAGE # ONLY
TRNE P1,200 ;WAS IT PAGE 0?
ADD T1,T2 ;NO - ADD IN PAGE FIELD
MOVEI P1,4 ;CONVERT TO 4 DIGIT SIXBIT
LSHC T1,-3
LSH T2,-3
SOJG P1,.-2 ;MAKE INTO ZONE DIGITS
LSH T2,-^D12 ;RIGHT JUSTIFY
IOR T2,['0000'] ;MAJIK
PUSH P,T2 ;STACKIT
JRST PNTDMP ;GO DUMP THIS MES
;HERE TO PRINT IOT (6) INSTRUCTIONS
PNTIOT: CAILE P1,6007 ;CHECK FOR BUILTIN
JRST PNTIOX ;NO - MUST BE DX10 SPECIFIC
ANDI P1,7 ;MASK OUT TRASH
PUSH P,DTAB(P1) ;STASH OP
JRST PNTDMP ;AND DUMP
;HERE FOR DX10 IOTS
PNTIOX: CAIL P1,6500 ;CHECK RANGE
CAILE P1,6577 ;FOR VALID IOT
JRST PNTXXX ;LOSE
PUSH P,XTAB-6500(P1)
JRST PNTDMP ;GO DUMP
;HERE TO DUMP STACKED ATOMS
PNTDMP: MOVE P1,P ;COPY OF PDP
SUB P1,[1,,1] ;LOOK FOR MARKER
SKIPE 0(P1) ;???
JRST .-2 ;NO - KEEP LOOKING
SUB P1,[1,,1] ;BACK ONE MORE
PUSH P,P1 ;SAVE THIS
AOBJN P1,PNTNXA ;ADVANCE AND START DUMPING
PNTNXT: MOVE T2,0(P1) ;FETCH ATOM
MOVEI T3,6 ;MAX 6 CHARS
PNTNX1: MOVEI T1,0 ;CLEAR T1
LSHC T1,6 ;GET CHAR
JUMPE T1,PNTNX2 ;SKIP NULLS
ADDI T1,40 ;CONVERT TO ASCII
PUSHJ P,LCHAR ;DUMP CHAR
PNTNX2: SOJG T3,PNTNX1 ;LOOP TILL DONE
MOVEI T1," " ;PRINT SPACE
PUSHJ P,LCHAR
PNTNXA: AOBJN P1,.+1 ;ADVANCE TO NEXT
CAME P1,P ;DONE
JRST PNTNXT
MOVE P,0(P) ;MORE OBSCURITY
JRST LCRLF ;CRLF AND RETURN
;MAJIK TABLES
RTAB: '***'
'BSW'
'RAL'
'RTL'
'RAR'
'RTR'
'***'
'***'
ITAB: 'AND'
'TAD'
'ISZ'
'DCA'
'JMS'
'JMP'
DTAB: 'SKON'
'ION'
'IOF'
'SRQ'
'GTF'
'RTF'
'SGT'
'CAF'
;MOBY TABLE FOR DX10 IOT'S
XTAB: 'CCC' ;6500
'SLB'
'STM'
'G8A'
'G8B'
'G8C'
'GBI'
'GTI'
'LCB'
'L8S'
'LSF'
'L8A'
'L8B'
'L8C'
'LIS'
'LBO'
'TCP'
'TBD'
'TSF'
'TSR'
'TCL'
'TCT'
'TSA'
'TRI'
'***' ;6530
'CAD'
'CCM'
'CSV'
'COP'
'CHL'
'CSE'
'CSU'
'T8R'
'TBP'
'TDN'
'TBC'
'TOR'
'***' ;6545
'***' ;6546
'***' ;6547
'MRD'
'MWR'
'D8S'
'LIL'
'LIR'
'GIL'
'GIR'
'I8S'
'***' ;6560
'***' ;6561
'***' ;6562
'***' ;6563
'***' ;6564
'***' ;6565
'***' ;6566
'SSA'
'SVB'
'SAD'
'SCM'
'SVA'
'SOP'
'SHL'
'SSE'
'SSU' ;6577
SUBTTL HEADER CONSTRUCTION SUBROUTINES
HEDTXT: POP P,T2 ;PRINT STRING, CALLED WITH PUSHJ
HRLI T2,(POINT 7,,) ;CHANGE PC TO BYTE POINTER
HEDTX2: ILDB T1,T2 ;GET NEXT BYTE
JUMPE T1,1(T2) ;RETURN ON 0 CHARACTER
PUSHJ P,HEDCHR ;PRINT CHARACTER
JRST HEDTX2 ;LOOP FOR MORE
HEDOCT: TDZA T3,T3 ;PRINT OCTAL NUMBER, CALLED BY PUSHJ
HEDDEC: MOVEI T3,2 ;PRINT DECIMAL NUM, CALLED BY PUSHJ
MOVE T4,T3 ;FOR DECIMAL NUMS, FORCE 2 DIGITS
HEDNUM: IDIVI T1,10(T3)
HRLM T1+1,(P)
SOSG T4 ;FORCE DIGITS
SKIPE T1
PUSHJ P,HEDNUM
HLRZ T1,(P)
HEDDIG: ADDI T1,"0" ;PRINT DIGIT
HEDCHR: IDPB T1,HEDPNT ;PRINT CHARACTER
POPJ P,
HED7: MOVEI T2,5 ;PRINT 5 ASCII CHARS, CALLED BY PUSHJ
HED7A: ROT T1,7 ;GET NEXT CHARACTER
TRNE T1,177 ;SKIP IF NULL
PUSHJ P,HEDCHR
SOJG T2,HED7A ;LOOP UNTIL 5 PRINTED
POPJ P,
;LIST HEADING
LHEAD: MOVEI T1,HEADER ;GET HEADER
PUSHJ P,LSTTX ;LIST IT
;FALL INTO LCRLF2
;LIST END OF LINE AND A BLANK LINE
LCRLF2: PUSHJ P,LCRLF
LCRLF: MOVEI T1,[BYTE (7)15,12]
;FALL INTO LSTTX
;LIST ASCIZ STRING
LSTTX: MOVE T2,T1 ;GET POINTER
HRLI T2,(POINT 7,,) ;SET ASCII POINTER
LSTTXL: ILDB T1,T2 ;GET CHARACTER
JUMPE T1,RETRET ;RETURN IF DONE
PUSHJ P,LCHAR ;ELSE LIST IT
JRST LSTTXL ;LOOP UNTIL DONE
;LIST SLASH - FALL INTO LTAB
LSLSH: MOVEI T1,"/"
PUSHJ P,LCHAR
;LIST TAB
LTAB: MOVEI T1,11 ;GET TAB
;FALL INTO LCHAR
;LIST CHARACTER
LCHAR: SOSG OUTHDR+2 ;COUNT CHARACTER IN BUFFER
JRST LCHARB ;NO ROOM--GO MAKE SOME
LCHARL: IDPB T1,OUTHDR+1 ;OK--STORE CHARACTER
RETRET: RETURN
LCHARB: OUT CHO, ;OUTPUT DATA BUFFER
JRST LCHARL ;AND NOW GO DO CHARACTER
ERROR Output device error
SUBTTL COMMAND SCANNER
GETCOM: OUTSTR [ASCIZ /File: /] ;TELL USER WE ARE WAITING
COMLP: PUSHJ P,GETNAM ;GET A SIXBIT NAME
JRST .+2
COMFND: MOVEI T2,0 ;CLEAR NAME
MOVSI T4,-BRKLEN ;LOOK FOR BREAK
HLRZ T3,BRKTAB(T4) ;TRY NEXT BREAK
CAME T1,T3 ;SEE IF MATCH
AOBJN T4,.-2 ;LOOP UNTIL MATCH
HRRZ T3,BRKTAB(T4) ;GET DISPATCH ADDRESS
JRST (T3) ;JUMP TO HANDLE BREAK
BRKTAB: " ",,COMNOP ;SPACE IS A NO-OP
".",,COMEXT ;DOT IS EXTENSION
":",,COMDEV ;COLON IS DEVICE
"[",,COMDIR ;BRAKET IS DIRECTORY
"/",,COMSWT ;SLASH IS SWITCH
12,,CMDEND ;RETURN AT END OF LINE, AFTER SAVING FILE NAME
32,,GOHOME ;IF ^Z
3,,GOHOME ;IF ^C
BRKLEN==.-BRKTAB
0,,COMERR ;ELSE, MUST BE ERROR
COMERR: USEROR Command error--type /H for help
COMNOP: PUSHJ P,SAVNAM ;STORE FILE NAME
JRST COMLP ;AND GO AROUND AGAIN
COMEXT: PUSHJ P,SAVNAM ;SAVE FILE NAME
PUSHJ P,GETNAM ;GET SIXBIT NAME
HLLOM T2,EXT ;SAVE EXT WITH FLAG FOR DOT
JRST COMFND ;AND GO AROUND AGAIN
COMDEV: MOVEM T2,DEV ;SAVE DEVICE
JRST COMLP ;GO AROUND AGAIN
COMDIR: PUSHJ P,SAVNAM ;SAVE FILE NAME
PUSHJ P,GETOCT ;GET OCTAL NOW
CAIN T1,"-" ;SEE IF DEFAULT
JUMPE T2,[PUSHJ P,GETCHR
JRST COMDIX]
HRLZ T2,T2 ;POSITION IT
SKIPN T2 ;SKIP IF SOMETHING THERE
GETPPN T2, ;NO--GET FROM SYSTEM
JFCL
HLLZM T2,DIRECT ;SAVE FOR LATER
CAIE T1,"," ;VERIFY COMMA
JRST COMERR ;NO--GIVE UP IN DISGUST
PUSHJ P,GETOCT ;GET PROGRAMMER
SKIPN T2 ;SKIP IF SOMETHING THERE
GETPPN T2, ;ELSE ASK MONITOR
JFCL
HRRM T2,DIRECT ;STORE FOR LOOKUP
CAIE T1,"," ;SEE IF SFD COMING
JRST COMDIX ;NO--GO FINISH UP
MOVEI T2,DIRPTH ;YES--SHIFT TO SFD
EXCH T2,DIRECT ; FORMAT
MOVEM T2,DIRPTH+2 ; ..
MOVSI T4,-5 ;MAX SFD COUNT
COMDIL: PUSHJ P,GETNAM ;GET SFD NAME
JUMPE T2,COMERR ;ERROR IF BLANK
MOVEM T2,DIRPTH+3(T4) ;STORE
CAIN T1,"," ;SEE IF MORE
AOBJN T4,COMDIL ;YES--GO GET UNLESS TOO MANY
COMDIX: CAIN T1,"]"
JRST COMLP
CAIN T1,12
JRST COMFND
JRST COMERR
;HERE ON END OF COMMAND TO CHECK AND DEFAULT DX10/DX20 TYPE VALUES
CMDEND: SKIPL A.DX10 ;SPECIFY BOTH /DX20 AND
SKIPGE A.DX20 ; /DX20?
CAIA ;NO, CONTINUE
USEROR <Can't specify both /DX10 and /DX20>
SETOB RHNUM,DRVNUM ;ASSUME DX10
SKIPL A.DX10 ;WERE WE CORRECT?
JRST SAVNAM ;YES, LEAVE RHNUM .LT. 0
SKIPGE RHNUM,A.DX20 ;/DX20 SPECIFIED?
SKIPL [V.DFLT] ;NO, IS DEFAULT DX20?
CAIA ;YES, CONTINUE WITH RHNUM .GE. 0
JRST SAVNAM ;NO, LEAVE RHNUM .LT. 0
SKIPGE T1,A.DX20 ;VALUE SPECIFIED ON /DX20 SWITCH?
MOVEI T1,V.DX2T ;NO, USE DEFAULT
MOVEM T1,A.DX20 ;AND STORE BACK
SKIPGE A.CHL ;/UNIT SPECIFIED?
JRST SAVNAM ;NO, LEAVE RHNUM .GE.0, DRVNUM .LT. 0
MOVE RHNUM,A.CHL ;GET VALUE OF /UNIT SWITCH
IDIVI RHNUM,10 ;COMPUTE CORRECT RHNUM AND DRVNUM
SAVNAM: SKIPE T2 ;IF NAME,
MOVEM T2,NAME ; SAVE FOR LOOKUP
POPJ P, ;RETURN
;HERE WHEN SWITCH TO BE PROCESSED
COMSWT: PUSHJ P,SAVNAM ;SAVE FILE NAME
PUSHJ P,GETNAM ;GET SIXBIT WORD
PUSH P,T1 ;SAVE BREAK CHARACTER
MOVE T1,[-SWTLEN,,SWTTAB] ;AOBJN POINTER TO NAMES
PUSHJ P,FNDNAM ;FIND NAME IN TABLE
HRRZ P1,T1 ;SAVE OFFSET OF MATCH
HLRZ T2,SWTVAL(P1) ;GET DEFAULT VALUE
MOVE T1,0(P) ;GET BACK BREAK CHARACTER
CAIE T1,":" ;SEE IF VALUE TYPED IN
JRST SWTWN2 ;NO, USE DEFAULT
CAIN P1,DX20DX ;PROCESSING /DX20 SWITCH?
JRST SWTWN1 ;YES, THAT'S DIFFERENT
PUSHJ P,GETOCT ;GET OCTAL VALUE OF SWITCH
MOVEM T1,0(P) ;SAVE BREAK CHARACTER
JRST SWTWN2 ;AND CONTINUE
SWTWN1: PUSHJ P,GETNAM ;GET SIXBIT VALUE OF SWITCH
MOVEM T1,0(P) ;SAVE BREAK CHARACTER
MOVE T1,[-DX2TBL,,DX2TAB] ;AOBJN POINTER FOR LEGAL VALUES
PUSHJ P,FNDNAM ;LOOK FOR IT
HRRZ T2,T1 ;MOVE TO PROPER PLACE
SWTWN2: HRRZ T3,SWTVAL(P1) ;GET ADDRESS OF SWITCH
JUMPE T3,HELP ;NONE--MUST BE /H
MOVEM T2,(T3) ;STORE ANSWER
CAIG P1,DEFIDX ;DID USER TYPE A SWITCH AFFECTING LOAD/START?
SETOM NODEF ;YES, DON'T DO AUTO START
POP P,T1 ;RESTORE BREAK CHARACTER
JRST COMFND ;GO HANDLE BREAK
NODEF: Z ;=0 IF USER SPECIFIES NO SWITCHES
SWTTAB: SIXBIT /CLEAR/
SIXBIT /DUMP/
SIXBIT /END/
SIXBIT /HELP/
SIXBIT /LOAD/
SIXBIT /START/
DEFIDX==.-SWTTAB-1
SIXBIT /UNIT/
UNIDX==.-SWTTAB-1
SIXBIT /TYPE/
SIXBIT /CPU/
SIXBIT /DX10/
SIXBIT /DX20/
DX20DX==.-SWTTAB-1
SWTLEN==.-SWTTAB
SWTVAL: V.CLR,,A.CLR ;DEFAULT,,LOCATION
V.DUMP,,A.DUMP
V.END,,A.END
0
0,,A.LOAD
V.STRT,,A.STRT
0,,A.CHL
V.TYPE,,A.TYPE
0,,A.CPU
0,,A.DX10
V.DX2T,,A.DX20
DX2TAB: SIXBIT/TX02/
SIXBIT/RP20/
DX2TBL==.-DX2TAB
;HERE IF /HELP
HELP: CAIN T1,12 ;SEE IF AT END OF LINE YET
JRST HELP1 ;YES--GO DO THE HELP
PUSHJ P,GETCHR ;NO--GET ANOTHER CHAR
JRST HELP ;AND LOOP
HELP1: MOVE 1,['BOOTDX']
PUSHJ P,.HELPR##
JRST START
FNDNAM: PUSH P,P1 ;SAVE P1
PUSH P,T1 ;SAVE INITIAL VALUE OF AOBJN POINTER
MOVSI P1,770000 ;GET INITIAL MASK
FNDNA1: MOVE T3,T2 ;COPY SIXBIT NAME TO MATCH
TDZ T3,P1 ;MASK WITH CURRENT MASK
JUMPE T3,FNDNA2 ;GO IF NO MORE BITS
ASH P1,-6 ;EXTEND MASK ANOTHER 6 BITS
JRST FNDNA1 ;AND LOOP
FNDNA2: SETZM T4 ;CLEAR FOUND COUNTER
FNDNA3: CAMN T2,(T1) ;EXACT MATCH?
JRST FNDNA5 ;YES
MOVE T3,(T1) ;GET CURRENT ENTRY
AND T3,P1 ;MASK IT
CAME T2,T3 ;MATCH NOW?
JRST FNDNA4 ;NO
SKIPE T4 ;ALREADY FOUND ANOTHER MATCH?
USEROR <Ambiguous switch or value -- Type /H for help>
MOVE T4,T1 ;KEEP POINTER TO MATCH
FNDNA4: AOBJN T1,FNDNA3 ;LOOP FOR NEXT VALUE
SKIPN T1,T4 ;ANY MATCHES?
USEROR <Unknown switch or value -- Type /H for help>
FNDNA5: SUB T1,0(P) ;COMPUTE OFFSET OF MATCH IN TABLE
POP P,(P) ;FLUSH STACK
POP P,P1 ;RESTORE P1
POPJ P, ;RETURN
GETNAM: MOVE T3,[POINT 6,T2]
MOVEI T2,0 ;CLEAR NAME
GETNM1: PUSHJ P,GETCHR ;GET NEXT CHAR
CAIL T1,"A"+40 ;SEE IF LC
CAILE T1,"Z"+40
JRST .+2
SUBI T1,40 ;YES--MAKE UC
CAIL T1,"0" ;SEE IF BREAK
CAILE T1,"Z" ; ..
RETURN
CAILE T1,"9" ;OR OK
CAIL T1,"A"
JRST .+2
RETURN
SUBI T1,40 ;CONVERT TO SIXBIT
TLNE T3,770000 ;SEE IF OVERFLOW
IDPB T1,T3 ;STORE RESULT
JRST GETNM1 ;LOOP FOR MORE
GETOCT: MOVEI T2,0 ;CLEAR RESULT
GETOC1: PUSHJ P,GETCHR ;GET NEXT ODGIT
CAIL T1,"0" ;SEE IF
CAILE T1,"7" ; BREAK
RETURN
LSH T2,3 ;MULT BY 8
ADDI T2,-"0"(T1) ;INCLUDE ODGIT
JRST GETOC1 ;LOOP
GETCHR: INCHWL T1 ;GET NEXT CHARACTER
JUMPE T1,GETCHR ;LOOP IF NULL
CAIE T1,177 ;IF RUB
CAIN T1,15 ;OR CR
JRST GETCHR ;LOOP
CAIL T1,175 ;IF ALTERNATE ALT MODE
MOVEI T1,33 ; STANDARDIZE
CAIN T1,33 ;IF ESCAPE
MOVEI T1,12 ; MAKE INTO EOL
CAIE T1,13 ;IF VTAB
CAIN T1,14 ; OR FORM
MOVEI T1,12 ; MAKE INTO LF
CAIN T1,11 ;SEE IF TAB
MOVEI T1," " ;YES, CHANGE TO SPACE
RETURN
SUBTTL UTILITY SUBROUTINES
;ROUTINE TO GET NEXT BYTE FROM FILE
;RETURNS BYTE IN P1 / PARTIAL CKSUM IN P2
GETBYT: PUSHJ P,GETC ;GET FILE CHAR
ADD P2,P1 ;ADD INTO CKSYM
POPJ P, ;RETURN
GETC: SOSG INHDR+2
PUSHJ P,GETBYI ;RE-FILL BUFFER
ILDB P1,INHDR+1 ;GET BYTE
POPJ P, ;RETURN
;ROUTINE TO GET NEXT WORD FROM FILE
;RETURNS 20000 IF LEADER/TRAILER , 1XXXX IF ADDRESS
;YYYY IF JUST DATA WORD
GETWRD: MOVEI P2,0 ;PARTIAL CKSUM TO ZERO
PUSHJ P,GETBYT ;GET A BYTE
LSH P1,6 ;PUT IN CORRECT PLACE
TRNE P1,20000 ;CHECK FOR LEADER/TRAILER
JRST GETCH8 ;CHECK CHL 8
PUSH P,P1 ;SAVE FIRST CHAR
PUSHJ P,GETBYT ;GET 2ND BYTE
TRNE P1,300 ;BETTER HAVE 7/8 ZERO
ERROR Illegal 2nd character
IOR P1,0(P) ;COMBINE
TPOPJ: POP P,T1 ;PRUNE PDL
CPOPJ: POPJ P, ;EXIT
;HERE TO CHECK RANDOMNESS
GETCH8: TRNE P1,7700 ;GOT ANYTHING
ERROR <Trash in file>
TRNN P1,10000 ;IGNORE FIELD SET ZERO
POPJ P,
JRST GETWRD ;...
;FILL BUFFER AND CHECK ERRORS
GETBYI: IN CHI,0 ;DO INPUT
POPJ P, ;OK RETURN
STATZ CHI,740000 ;HARD ERROR?
ERROR <Input file read error>
STATZ CHI,20000 ;EOF?
ERROR <Unexpected EOF>
POPJ P, ;SYSTEM CONFUSED
;ROUTINE TO CHECK WHAT TYPE OF FILE WE ARE READING
CHKLFT: PUSHJ P,GETC ;GET FIRST CHAR OF FILE
JUMPE P1,CHKB ;SEE IF BINARY IF NULL
CAIE P1,"8" ;SEE IF AN ASCII '8'
JRST [PUSHJ P,SKPCOM ;SKIP COMMENT
JRST CHKLFT] ;TRY AGAIN
SETOM A8FLG ;SAY A8 FILE
AOS INHDR+2 ;BACKUP INPUT FILE
MOVSI T1,70000 ;BACK UP BYTE PNTR
ADDM T1,INHDR+1 ;...
POPJ P, ;RETURN
CHKB: SETSTS CHI,CHIMOD ;CHANGE TO BINARY MODE
MOVSI T1,(POINT 36,0)
HLLM T1,INHDR+1
AOS T1,INHDR+2 ;ADJUST COUNT CORRECTLY
IDIVI T1,5
SKIPE T2
ADDI T1,1 ;ROUND UP
MOVEM T1,INHDR+2
SETZM A8FLG ;SAY BIN FILE
POPJ P,
;ROUTINE TO SKIP COMMENTS
SKPCOM: CAIE P1,";" ;VALID COMMENT CHAR?
ERROR <File not in A8 format>
SKPCM1: PUSHJ P,GETC ;GET CHAR TILL EOL
CAIE P1,12 ;LINE FEED?
JRST SKPCM1 ;NO - LOOP
POPJ P, ;YES - RETURN
;ROUTINE TO DO THE SETUUO THAT WILL FORCE US TO RUN ONLY ON THE
;CPU SPECIFIED IN THE /CPU SWITCH. IF NO SWITCH IS SPECIFIED,
;CPU 0 IS ASSUMED.
SETCPU: SKIPGE T2,A.CPU ;CPU SPECIFIED?
MOVEI T2,0 ;NO, ASSUME ZERO
MOVEI T1,SP.CR0 ;GET CPU0 BIT
LSH T1,(T2) ;SHIFT TO POSITION FOR THIS CPU
HRLI T1,.STCPU ;SETUP SETUUO FUNCTION CODE
SETUUO T1, ;PUT US ON THAT CPU
WARNCR <Unable to restrict execution to specified CPU>
POPJ P, ;RETURN
;PDP-8 A8 UTILITIES
GET2W: PUSH P,[0] ;INIT ANSWER
PUSHJ P,GETA8 ;GET FIRST CHAR
JRST GET2X ;EXIT IF NOT DIGIT
MOVEM P1,0(P) ;STASH ON PDL
PUSHJ P,GETA8 ;GET NEXT
JRST GET2X ;MUST BE SINGLE DIGIT
EXCH P1,0(P) ;NEW LOW ORDER BYTE
LSH P1,6 ;MAKE HIGH ORDER BYTE
IORM P1,0(P) ;COMBINE
PUSHJ P,GETC ;GET NEXT FILE CHAR
GET2X: MOVE P2,P1 ;RETURN BREAK CHAR IN P2
POP P,P1 ;RESTORE WORD TO P1
POPJ P, ;EXIT
;GET NEXT FILE CHAR AND RETURN LOW 6 BITS
GETA8: PUSHJ P,GETC ;GET CHAR FROM FILE
CAIE P1,"," ;CHECK TERMINATOR
CAIN P1,15
POPJ P, ;NON SKIP RETURN
ANDI P1,77 ;TRIM TO LOW ORDER 6-BIT
JRST CPOPJ1 ;SKIP IF CHAR OK
;GET WORD COUNT FFROM FILE
WCREAD: PUSHJ P,GETC ;GET CHARACTER
CAIE P1,"8" ;CHECK VALIDITY
JRST [PUSHJ P,SKPCOM ;SKIP COMMENT
JRST WCREAD]
PUSHJ P,GETC ;GET NEXT CHARACERR
CAIE P1," " ;BETTER BE A SPACE
ERROR <File not in correct A8 format>
SETZM CHKSUM ;INIT CHECKSUM
;NOW GET DATA WORD
WDREAD: PUSHJ P,GET2W ;GET 12 BIT NUMBER
ADDM P1,CHKSUM ;ADD TO CHECKSUM
CAIE P2,"," ;GRNTEE COMMA TERMINATOR
ERROR <File not in correct A8 format>
POPJ P, ;RETURN (ANSWER IN P1)
;PRINT OCTAL 4 DIGIT NUMBERS
L6OCT: SKIPA T3,[6] ;GRNTEE 6 DIGITS
L4OCT: MOVEI T3,4 ;GRNTEE 4 DIGITS
PNTO1: IDIVI T1,10
HRLM T2,0(P)
SOSLE T3
PUSHJ P,PNTO1 ;RECURSE
PNTO2: HLRZ T1,0(P) ;GET DIGIT
ADDI T1,"0"
JRST @OCHLOC
TTOCH: OUTCHR T1 ;PRINT IT
POPJ P, ;RETURN
;CLEANUP ROUTINE
EXITX: JSP T1,.+1 ;GET PC
TLNN T1,(1B6) ;CHECK USER IOT
JRST EXITXA ;JUST LEAVE
PUSHJ P,HALT8 ;STOP '8 IF IN USER IOT
;HERE TO EXIT
GOHOME: PUSHJ P,RESTOR ;RESTORE STATUS/CLR ERRORS
EXITXA: RESET ;TURN OFF USER IOT
HLLZM .JBINT## ;DISABLE ^C INTERCEPT
EXIT 1, ;.
JRST .-1
;ROUTINE TO RESTORE STATUS REG
RESTOR: JUMPGE RHNUM,CPOPJ
MOVEI T1,1 ;ANOTHER SNOOZE
SLEEP T1,
JFCL
MOVEI T1,CLRERR ;CLEAR ERRORS
XCT PDCCNO(W) ;...
MOVE T1,PISAVE ;PUT REG BACK
XCT T1,PDCCNO(W)
POPJ P, ;RETURN
;PRINT CONFIG INFO
PNTCNF: OUTSTR [ASCIZ /" Micro-code version: /]
MOVE T1,VERMP
PUSHJ P,LOCT ;PRINT OCTAL
OUTCHR ["("]
MOVE T1,EDTMP
PUSHJ P,LOCT
OUTSTR [BYTE (7)")",15,12]
POPJ P,
;ROUTINE TO TYPE OUT OCTAL NUMBERS AS THEY ARE
LOCT: IDIVI T1,10 ;GET FIRST DIGIT EVEN IF ZERO
HRLM T2,0(P) ;STORE ON PDL
SKIPE T1 ;QUITE WHEN ZERO
PUSHJ P,LOCT
JRST PNTO2 ;TYPE IT
SUBTTL SPECIAL PDP-8 ROUTINES
;ROUTINE TO RESET DX10 AND STOP THE '8
RESET8: PUSHJ P,SETCPU ;SET CPU ONLY ON CPU SPECIFIED
MOVEI T1,CCINT ;SET UP ^C INTERCEPT
HRRM T1,.JBINT## ;SAVE IN CORRECT PLACE
SETZB T1,CCINTP ;ZAP
TRPSET T1, ;GET GOOD PRIVS
ERROR <TRPSET failed>
JUMPGE RHNUM,RESET2
XCT PDCCNI(W) ;GET STATUS REG
;**;[23] after RESET8 plus 7 lines insert code
SKIPN T1 ;[23] skip if DX10 exists
USEROR No DX10 channel on specified CPU
;[23] give him an error and restart
ANDI T1,PIMASK ;MASK WHAT WE WANT TO SAVE
MOVEM T1,PISAVE ;SAVE IT
SKIPGE A.DUMP ;SKIP RESET IF DUMPING
SKIPL A.END
JRST NORST
MOVE T1,[DXCLR] ;CLEAR OUT DX10
XCT PDCDTO(W) ;...
NORST: XCT PDCCNI(W) ;GET RUN INDICATOR
TLNE T1,RUNIND ;IS '8 RUNNING
PUSHJ P,HALT8 ;YES - STOP IT
MOVEI T1,1 ;SLEEP A SEC HERE TOO
SLEEP T1,
JFCL
MOVEI T1,CLRERR
XCT PDCCNO(W) ;ZAP REG ONCE MORE
MOVE T1,[RSEL,,MPCTL]
XCT PDCDTO(W) ;SELECT SW REG
XCT PDCDTI(W) ;READ IT
ANDI T1,MPSS!MPHALT!MPCONT
TRZE T1,MPCONT ;CLEAR CONT & SKIP IF OFF
XCT PDCDTO(W) ;TURN IT OFF IF ON
MOVEM T1,SW8 ;SAVE REG
POPJ P, ;RETURN
;ROUTINE TO TRY TO STOP PDP-8
HALT8: JUMPGE RHNUM,CPOPJ
MOVE T1,[RSEL,,MPCTL]
XCT PDCDTO(W) ;SELECT CORRECT REG
XCT PDCDTI(W) ;READ IT
TRO T1,MPHALT ;SET HALT FLAG
XCT PDCDTO(W) ;HALT '8
MOVEI T2,2 ;TRY TWICE
HALT8A: MOVEI T1,1 ;SLEEP FOR A SEC
SLEEP T1, ;ZZZZZ
JFCL
XCT PDCCNI(W) ;READ STATUS
TLNE T1,RUNIND ;RUNNING?
SOJG T2,HALT8A ;YES - TRY ONCE MORE
JUMPG T2,CPOPJ ;OK IF OFF
ERROR <Cannot halt DX10>
;ROUTINE TO CLEAR OUT PDP-8 MEMORY
CLEAR: JUMPGE RHNUM,CLRDX
TELLCR Clearing DX10
MOVEI P1,0 ;START OF AREA TO CLEAR
MOVE T1,A.CLR ;CHECK VALIDITY OF ADDRESS
CAIL T1,V.CLR ;CHECK UPPER BOUND
MOVEI T1,V.CLR ;DEFAULT
MOVEM T1,A.CLR ;SAVE VALUE
MOVE T1,[RSEL,,MPADR]
XCT PDCDTO(W) ;SELECT ADDR
MOVE T1,P1 ;SET ADDESS
XCT PDCDTO(W) ;...
CLEARL: MOVE T1,[RSEL,,MPCTL]
XCT PDCDTO(W) ;SELECT CTL REG
MOVEI T1,ENDEP!HLTINS ;ZAP MEMORY WITH HALTS
IOR T1,SW8 ;OLD SW REG
XCT PDCDTO(W) ;WRITE IT
AOS T1,P1 ;ADVANCE TO NEXT
CAMLE T1,A.CLR ;DONE?
POPJ P, ;YES - RETURN
PUSHJ P,CKCPMA ;CHECK MEM ADV
JRST CLEARL ;LOOP TILL DONE
;ROUTINE TO CHECK IF AUTO MA ADVANCE HAPPENED
;C(T1) HAS CORRECT VALUE
CKCPMA: PUSH P,T1 ;SAVE T1
MOVE T1,[RSEL,,MPADR]
XCT PDCDTO(W) ;SELECT ADR
XCT PDCDTI(W) ;READ WHAT IT THINKS
ANDI T1,7777 ;MASK
CAMN T1,0(P) ;AGREE?
JRST CKCPMX ;YES - EXIT
SETOM VERERR ;FLAG ERROR
OUTSTR [ASCIZ /? CPMA incr error. CPMA = /]
PUSHJ P,L4OCT ;PRINT ERROR INFO
OUTSTR [ASCIZ / should be = /]
MOVE T1,0(P) ;GET CORRECT VALUE
PUSHJ P,L4OCT ;PRINT IT
OUTSTR [BYTE (7)15,12] ;CRLF
MOVE T1,0(P) ;NOW SET CORRECT VALUE
XCT PDCDTO(W) ;...
CKCPMX: MOVE T1,[RSEL,,MPCTL]
XCT PDCDTO(W) ;RESELECT CTL REG
JRST TPOPJ ;PRUNE & EXIT
;ROUTINE TO START '8 AT C(P2)
START8: CAILE P2,7777 ;CHECK VALIDITY
ERROR <Invalid starting address>
MOVE T1,[RSEL,,MPCTL]
XCT PDCDTO(W) ;SELECT CTRL REG
MOVEI T1,MPHALT ;GRNTEE HALT UP
XCT PDCDTO(W) ;...
MOVE T1,[RSEL,,MPADR]
XCT PDCDTO(W) ;SELECT ADDRS
MOVE T1,P2 ;GET START LOC
XCT PDCDTO(W) ;STUFF IT
MOVE T1,[RSEL,,MPCTL]
XCT PDCDTO(W)
MOVEI T1,MPCONT ;SET CONTINUE
XCT PDCDTO(W) ;START WORLD
MOVEI T1,MPERR ;CLEAR 8A ERROR
XCT PDCCNO(W)
MOVEI T2,2 ;TRY TWICE
STARTL: MOVEI T1,1 ;SLEEP FOR 1 SEC
SLEEP T1, ;ZZZZ
JFCL
XCT PDCCNI(W) ;READ REGS
TRNN T1,MPERR ;CHECK EVERYTHING OK
TLNN T1,RUNIND ;RUNNING?
SOJG T2,STARTL ;NO - TRY AGAIN
JUMPG T2,CPOPJ ;EXIT IF OK
ERROR <Cannot start DX10>
SUBTTL DX20 LOAD AND START ROUTINES
;TESDSW - CHECK THE SPECIFIED DX20 BY /D SWITCH
;
; CALL TESDSW
;
; RETURN+1:ALWAYS W/H NO ERROR
; GOTO ERR17/ERR18 WHEN NO SPECIFIED RH20 OR DRIVE
TESDSW: MOVE T3,RHNUM ;GET RH20 NUMBER
PUSHJ P,CHKRH2 ;SPECIFIED RH20 THERE?
ERROR <Specified RH20 does not exist>
MOVE T4,DRVNUM ;GET DRIVE NUMBER
PUSHJ P,CHKDRV ;SPECIFIED DRIVE DX20?
ERROR <Specified device is not a DX20>
PUSHJ P,PRHDRV ;PRINT OUT DX20 SELECTED
POPJ P, ;GOOD RETURN
;RESET2 - RESET THE DX20
RESET2: MOVEI T3,DXMTR ;GET THE REGISTER
MOVE T4,DRVNUM ;GET THE DRIVE NUMBER
MOVEI T2,DX.RST ;SET THE RESET BIT
PUSHJ P,WTREG ;RESET DX20
POPJ P,
;CHKRH2 - CHECKS IF THE SPECIFIED RH20 IN EXISTENCE, IF SO, SETS IT UP.
; T3/RH20 NUMBER
;
; CALL CHKRH2
;
; RETURN+1: FAIL, SPECIFIED RH20 NOT EXISTS.
; RETURN+2: FOUND SPECIFIED RH20, AND SET IT UP FOR OPERATION
; DESTROYS T3
CHKRH2: LSH T3,2 ;MULTIPLY RH20 NUMBER BY 4
; ***TEMPORARY WAY TO GET DEVICE CODE
ADDI T3,540 ;540= DEVICE CODE FOR RH20
LSH T3,^D24 ;FLUSH LEFT
PUSHJ P,DEVXCT ;GET STATUS BACK
CONI 0,T1 ; IN T1
JUMPLE T1,CPOPJ ;NOT THERE IF CONI YIELDS ALL ZEROS.
; SIGN BIT MEANS KLIPA OR KLINI,
; NOT REALLY AN RH20.
TRNE T1,400 ;MASSBUS ENABLED?
JRST CHKRH3 ;YES
PUSHJ P,DEVXCT ;NO, DO SO NOW
CONO 0,400
CHKRH3: MOVE T1,[CONO 0,CO.MEN(T2)] ;SET UP IOT'S????
IOR T1,T3 ;SET DEVICE CODE
MOVEM T1,RH2CNO ;STORE IT
MOVE T1,[CONI 0,T1] ;CONI STATUS
IOR T1,T3 ;SET DEVICE CODE
MOVEM T1,RH2CNI ;STORE IT
MOVE T1,[DATAO 0,T2] ;DATAO INSTR.
IOR T1,T3 ;SET DEVICE CODE
MOVEM T1,RH2DTO ;STORE IT
MOVE T1,[DATAI 0,T1] ;DATAI INTR.
IOR T1,T3 ;SET DEVICE CODE
MOVEM T1,RH2DTI ;STORE IT
JRST CPOPJ1 ;SKIP RETURN
SUBTTL ROUTINES FOR COMMAND PROCESSING MODULE
;LOKDX - LOOK FOR THE ONLY ONE DX20 ON THE SYSTEM
;
; CALL LOKDX
;
; RETURN+1: SUCCESS RETURN, RETURN RHNUM & DRVNUM FOR THE DX20
; USES Q1 & Q2, CONSIDER ERROR IF 0 OR MORE THAN 1 DX20'S FOUND
LOKDX: MOVSI Q1,-10 ;SETUP COUNTER, AT MOST 10 RH20'S
LOKDX1: HRRZ T3,Q1 ;GET RHNUM
PUSHJ P,CHKRH2 ;CHECK FOR EXISTENCE
JRST LOKDX4 ;JUMP, NOT EXISTS
HRRZM Q1,RHNUM ;YES, SAVE RHNUM FOR THIS RH20
MOVSI Q2,-10 ;SETUP COUNTER, AT MOST 10 DRIVES
LOKDX2: HRRZ T4,Q2 ;GET DRIVE NUMBER
PUSHJ P,CHKDRV ;CHECK DRIVE IF DX20?
JRST LOKDX3 ;JUMP,NOT THIS DRIVE
TROE F,DXFND ;WAS DX20 FOUND?
ERROR <More than 1 DX20 found - use /UNIT switch>
HRRZM Q2,DRVNUM ;ONLY ONE FOUND, SAVE DRVNUM
HRRZM Q1,XRHNUM ;SAVE THE RHNUM FOR THE RH20
MOVE T4,[XWD RH2CNI,XRHCNI] ;SET UP T4
BLT T4,XRHDTO ;SAVE IO INTR.'S FOR THIS RH20
LOKDX3: AOBJN Q2,LOKDX2 ;GO BACK, TRY NXT DRIVE
LOKDX4: AOBJN Q1,LOKDX1 ;GO BACK, TRY NXT RH20
TRZN F,DXFND ;FOUND THE DX20?
ERROR <No DX20 found>
MOVE RHNUM,XRHNUM ;YES,RESTORE THE RH20 NUMBER
MOVE T4,[XWD XRHCNI,RH2CNI] ;SETUP T4
BLT T4,RH2DTO ;RESTORE IO INSTR. FOR THE RH20
POPJ P, ;YES, RETURN
;CLRDX - CLEARS THE MEMORY OF DX20
;
; CALL CLRDX
; USES Q1
CLRDX: MOVEI Q1,3777 ;2K LOC.'S IN CRAM
CLRDX1: MOVE T2,Q1 ;GET ADDR. IN T2
PUSHJ P,PRECR ;SET IT UP
PREWT (DXDR0) ;SELCT IR REGISTER
PUSHJ P,WTRGX ;WRITE INTO CRAM
SOJG Q1,CLRDX1 ;BACK DO IT AGAIN
;NOW LOAD WORKING MEMORY
MOVEI Q1,1777 ;1K LOC.S IN WM
MOVEI T2,0 ;START AT LOC. 0
PUSHJ P,PREWM ;SETS UP FOR WM
MOVEI T1,11400 ;MAKE MICROINTR.(MOVEI MEM MA+1)
PUSHJ P,XI ;EXECUTE INSTR. IN T1
SOJG Q1,.-1 ;DO IT AGAIN
PUSHJ P,POSWM ;RESTORE LOC 0 OF CRAM
TELLCR <Clearing DX20>
POPJ P, ;THEN, RETURN
;HERE TO LOAD THE DX20
LOAD20: PUSHJ P,GETLIN ;GET LOAD LINE FROM FILE
; T1/ WORD COUNT, T2/ LOAD ADDR.
JUMPE T1,LDEND ; 0 WC MEANS LAST LINE
MOVN Q1,T1 ;NEGATE WORD COUNT
HRLZ Q1,Q1 ;SET UP INDEX FOR LOADING LOOP
SKIPN CFLAG ;SKIP IF CRAM LOAD LINE
JRST LDWM ;JUMP IF WM LOAD LINE
PUSH P,T2 ;SAVE OLD LOAD ADDR. ON TOP OF STACK
LDDX1: MOVE T2,(P) ;GET BACK OLD LOAD ADDR. FROM STACK
HRRZ T3,Q1 ;GET OFFSET IN T3
ADD T2,T3 ;ADJUST CURRENT LOAD ADDR.
PUSH P,T2 ;REMEMBER PC
PUSHJ P,PRECR ;SETS UP PC FOR CRAM, T2/ LOAD ADDR.
MOVE T2,LINDAT(Q1) ;GET DATA WORD
POP P,T3 ;GET ADDRESS TO LOAD
CAIN T3,MAGICA ;IS IT THE ADDRESS WHERE
; THE MAGIC VALUE GETS STORED?
SKIPE A.DX20 ;AND CONTROLLER A TX02?
CAIA ;NO
MOVEI T2,MAGICV ;YES,
ANDI T2,177777 ;MAKE SURE 16 BITS
MOVEI T3,DXDR0 ;SELCT IR
PUSHJ P,WTRGX ;LOAD CRAM FROM IR
AOBJN Q1,LDDX1 ;LOOP BACK
POP P,T2 ;TAKE IT OFF STACK
JRST LOAD20 ;GET NEXT LINE
;LOAD WORKING MEMORY FOR WM LOAD LINE
LDWM: PUSHJ P,PREWM ;SETS UP MA FOR WM LOADING
LDWM1: MOVE T1,LINDAT(Q1) ;GET DATA WORD
ANDI T1,377 ;MAKE SURE 8 BITS
TRO T1,11400 ;MAKE MICROINTR. (MOVEI MEM MA+1)
PUSHJ P,XI ;EXECUTE MICRO INTR.
AOBJN Q1,LDWM1 ;BACK FOR NEXT WORD
PUSHJ P,POSWM ;RESTORE LOC 0 OF CRAM
JRST LOAD20 ;FOR THE NXT LINE
LDEND: SKIPE T2 ;NON-0 DX20 STARTING ADDR.?
MOVEM T2,A.STRT ;YES, STORE IT
DMOVE T1,FILNAM
MOVE T4,DIRECT ;LOOKUP THE FILE AGAIN
LOOKUP CHI,T1 ; IN ORDER TO DO THE VERIFY
ERROR <Second LOOKUP on file failed>
;FALL INTO VERIFY CODE
VRFDX: PUSHJ P,GETLIN ;GET LOAD LINE FROM FILE
; T1/ WORD COUNT, T2/LOAD ADDR
JUMPE T1,VRFEND ;LAST LINE READ FROM FILE
MOVN Q1,T1 ;NEGATE WORD COUNT INTO Q1
HRLZ Q1,Q1 ;SETS UP INDEX FOR VERIFY LOOP
SKIPN CFLAG ;SKIP, IF GOT CRAM LOAD LINE
JRST VRFWM ;JUMP, IF WM LOAD LINE
PUSH P,T2 ;SAVE OLD LOAD ADDR. ON STACK
VRFDX1: MOVE T2,(P) ;GET BACK OLD LOAD ADDR. FROM STACK
HRRZ T3,Q1 ;GET OFFSET TO LOAD
ADD T2,T3 ;ADJUST CURRENT LOAD ADDR.
ANDI T2,7777 ;MAKE SURE 12 BIT PC
PUSH P,T2 ;REMEMBER PC
TRO T2,IR.EN+PC.EN+PC.AI ;SET BITS FOR READ
MOVEI T3,DXDR1 ;SELCT PC
PUSHJ P,WTRGX ;WRITE PC
MOVEI T3,DXDR0 ;SELCT IR
PUSHJ P,RDRGX ;READ CRAM FROM IR
MOVE T2,LINDAT(Q1) ;GET DATA WORD
POP P,T3 ;GET ADDRESS TO LOAD
CAIN T3,MAGICA ;IS IT THE ADDRESS WHERE
; THE MAGIC VALUE GETS STORED?
SKIPE A.DX20 ;AND CONTROLLER A TX02?
CAIA ;NO
MOVEI T2,MAGICV ;YES,
ANDI T2,177777 ;MAKE SURE 16 BITS
MOVEI T4,[ASCIZ/CRAM/] ;MESSAGE IN CASE OF ERROR
CAME T2,T1 ;VERIFY CRAM WORD
PUSHJ P,VRFTYP ;GIVE DATA
MOVEI T3,DXDR7 ;SELCT MBRA37
PUSHJ P,RDRGX ;READ IT IN
TRNE T1,IR.PER ;CHECK IF IR PARITY ERROR
ERROR <CRAM parity error during verification>
AOBJN Q1,VRFDX1 ;LOOP BACK FOR NEXT WORD
POP P,T2 ;CLEAN THE STACK
JRST VRFDX ;BACK FOR NEXT LINE
;VERIFY WORKING MEMEORY AGAIN WM LOAD LINE
VRFWM: PUSH P,T2 ;SAVE LOAD ADDR
PUSHJ P,PREWM ;SETS UP WORKING MEMORY
VRFWM1:
MOVEI T3,DXDR5 ;SELCT DXDR5 HAS WM BYTE
PUSHJ P,RDRGX ;READ WM ,AT LOC. C(MA), IN T1
ANDI T1,377 ;ONLY 8 BITS
MOVE T2,LINDAT(Q1) ;GET DATA WORD
MOVE T3,0(P) ;GET BASE LOAD ADDRESS BACK
ADDI T3,(Q1) ;OFFSET TO CURRENT WORD
MOVEI T4,[ASCIZ/Working memory/] ;MESSAGE FOR ERROR
CAME T2,T1 ;VERIFY WM WORD
PUSHJ P,VRFTYP ;TELL OF ERROR
AOBJN Q1,VRFWM2 ;GET READY FOR NEXT WM WORD
POP P,(P) ;BRING STACK INTO PHASE
PUSHJ P,POSWM ;RESTORE LOC 0 OF CRAM
JRST VRFDX ;GET NEXT LINE
VRFWM2: MOVEI T1,1400 ;MAKE MICROINTR. (MOVEI NOOP MA+1)
PUSHJ P,XI ;INCREMENT MA
JRST VRFWM1 ;BACK FOR NEXT WORD
VRFEND:
; SKIPN T2 ;IF T2 IS 0,
; MOVEI T2,1 ;TAKE DEFAULT STARTING ADDR.=1
; CAME T2,STALOC ;VERIFY DX20 STARTING ADDR.
; JRST ERR16 ;ERROR, NOT MATCH
SKIPE VERERR ;ANY VERIFY ERRORS?
ERROR <Verify error>
PREWT (DXDR1) ;SELCT PC
TRO T2,PC.EN+IR.EN ;SET BITS
PUSHJ P,WTRGX ;SET PC TO 0
MOVEI T3,DXDR0 ;SELCT IR
PUSHJ P,RDRGX ;GET LOC. 0 OF CRAM
MOVE Q1,T1 ;SAVE IT IN Q1
SKIPGE P2,A.STRT ;LOOK FOR STARTING ADDRS
MOVE P2,A.LOAD ;...
CAIN P2,V.STRT ;DEFAULT (DX10) START ADDR?
MOVEI P2,1 ;YES, SUBSTITUTE DEFAULT DX20 START
SKIPG P2 ;ONE SPECIFIED?
MOVEI P2,1 ;DEFAULT START ADDR IS 1
SKIPL A.LOAD ;LOAD ONLY?
MOVEI P2,0 ;YEP
SKIPE P2 ;SHOULD WE START IT
PUSHJ P,STADX ;YES - TRY TO
SKIPN P2 ;GIVE CORRECT MESSAGE
TELLCR DX20 loaded.
SKIPE P2
TELLCR DX20 started.
CLOSE CHI, ;TERMINATE INPUT CHL
RELEAS CHI,
PUSHJ P,PVERSN ;PRINT CONFIG INFO
JRST GOHOME ;WHEW
;PVERSN - PRINTS VERSION & EDIT NUMBER OF MICRO-CODE ON TERMINAL
;
; CALL PVERSN
;
PVERSN: OUTSTR [ASCIZ /Micro code version /]
LDB T1,VR.NUM
PUSHJ P,LOCT
OUTSTR [ASCIZ /(/]
LDB T1,ED.NUM
PUSHJ P,LOCT
OUTSTR [ASCIZ /)
/]
POPJ P,
;VRFTYP - GIVE DATA ON VERIFICATION ERRORS
;T1/DATA READ FROM MEMORY OF DX20
;T2/DATA READ FROM FILE
;T3/ADDRESS OF ERROR
;T4/MESSAGE PREFIX ADDRESS
; CALL VRFTYP
VRFTYP: OUTSTR [ASCIZ/? /]
OUTSTR (T4) ;APPEND DESCRIPTION FROM CALLER
OUTSTR [ASCIZ/ verification error at /]
PUSH P,T2 ;SAVE GOOD DATA
PUSH P,T1 ;SAVE BAD DATA
MOVE T1,T3 ;GET ADDRESS
PUSHJ P,L6OCT ;PRINT ADDRESS
OUTSTR [ASCIZ/, has /]
POP P,T1 ;GET BAD DATA
PUSHJ P,L6OCT ;TYPE IT
OUTSTR [ASCIZ/, should have /]
POP P,T1 ;GET GOOD DATA
PUSHJ P,L6OCT ;TYPE IT
OUTSTR [ASCIZ/
/]
SETOM VERERR ;SET ERROR FLAG
POPJ P, ;AND RETURN
;STADX - STARTS THE MICRO-CODE IN DX20
;
; CALL STADX
;
STADX: PREWT (DXMTR) ;STOP MICROPROCESOR
PUSHJ P,WTRGX ;
MOVE T2,P2 ;GET STARTING ADDR. FOR MICROCODE
TRO T2,PC.EN+PC.AI+IR.EN ;SET BITS
MOVEI T3,DXDR1 ;SELECT PC
PUSHJ P,WTRGX ;SET PC TO START ADDR.
PREWT (DXMTR) ;SELCT DXMTR
TRO T2,MP.STA ;SET START BIT
PUSHJ P,WTRGX ;START MICRO-PROCESSOR
POPJ P, ;RETURN
;GETLIN - READS IN A LINE OF DATA WORDS TO BE LOADED INTO CRAM OR
; WORKING MEMORY
;
; CALL GETLIN
;
; RETURN+1: ALWAYS
; LINDAT IS THE TALBE WHICH HAS THE CONVERTED DATA WORDS
; T1/ WORD COUNT OF DATA WORDS IN THE TABLE
; T2/ LOAD ADDR
; CFLAG PROPERLY SET, 1S=DATA WORDS FOR CRAM, 0= FOR WORKING MEMORY
; USES P1 AS PTR, P2 AS LOOP INDEX
GETLN0: PUSHJ P,GETC
CAIE P1,12
JRST GETLN0
GETLIN: MOVE T4,[LINWC,,LINWC+1] ;INITIALIZE WORK AREA
SETZM LINWC ;
BLT T4,CHKSUM
MOVEI T3,^D32*5 ;MAXIMUN NUMBER OF CHAR.S
SETZM CFLAG# ;CFLAG=1S MEANS FOR CRAM
PUSHJ P,GETC
CAIN P1,";" ;IS IT COMMENT LINE?
JRST GETLN0 ;YES, IGNORE IT
CAIE P1,"C" ;CRAM LOAD LINE?
JRST GTLNA ;NO, SEE IF WM LOAD LINE
SETOM CFLAG ;YES, SET FLAG
JRST GTLNB ;JUMP AROUND
GTLNA: CAIE P1,"W" ;WM LOAD LINE?
ERROR <1st character wrong in dataline>
GTLNB: PUSHJ P,GETC ;GET NEXT CHAR.
CAIE P1," " ;MUST BE BLANK
ERROR <2nd character wrong in dataline>
PUSHJ P,GTWRD ;GET NEXT WORD
ERROR <format error in dataline>
MOVEM T1,LINWC ;SAVE WORD COUNT FOR THE LINE
MOVEM T1,CHKSUM ;INITIALIZE CHECKSUM FOR THE LINE
PUSHJ P,GTWRD ;GET NEXT WORD
ERROR <format error in dataline>
ADDM T1,CHKSUM ;UPDATE CHKSUM
DPB T1,[POINT 16,LINWC,19] ;SAVE LOAD ADDR.
MOVSI P2,-^D32 ;SETUP LOOP INDEX FOR SUBSEQUENT WORDS
; LINDAT HOLDS AT MOST 32 WORDS
GETLI1: PUSHJ P,GTWRD ;GET NEXT WORD
JRST GETLI2 ;LAST WORD, CHKSUM, READ IN T1
ADDM T1,CHKSUM ;UPDATE CHKSUM
MOVEM T1,LINDAT(P2) ;SAVE DATA WORD
AOBJN P2,GETLI1 ;LOOP BACK
ERROR <too many words in dataline>
GETLI2: MOVEM T1,LINDAT(P2) ;SAVE EVEN CHKSUM
ADD T1,CHKSUM ;ADD CHKSUM INTO T1
TRNE T1,177777 ;CHECKSUM SHOULD BE 0
ERROR <checksum error in dataline>
LDB T1,[POINT 16,LINWC,35] ;WC IN T1
LDB T2,[POINT 16,LINWC,19] ;LOAD ADDR. IN T2
POPJ P, ;NONSKIP RETURN
;GTWRD - GET A DATA WORD FROM DATLIN WHICH IS A CHAR. STRING
; CONVERT THE ASCIIZED DATA WORD INTO BINARY
;
; CALL GTWRD
;
; RETURN+1: DATA WORD DELIMITED BY CR
; RETURN+2: DATA WORD DELIMITED BY ,
; T1/ CONVERTED DATA WORD
; USES P1 AS PTR
GTWRD: SETZ T1, ;T1 WILL HAVE RESULT DATA
GTWRD1: PUSHJ P,GETC
CAIN P1,"," ;SKIP IF NOT COMMA
JRST CPOPJ1 ;GOT THE DATA WORD
;SKIP RETURN
CAIN P1,15 ;SKIP IF NOT CR
JRST GTWRD1 ;CR, THROW IT AWAY AND LOOK FOR LF
CAIN P1,12
POPJ P, ;RETURN, GOT LAST DATA WORD IN LINE
LSH T1,6 ;MAKE ROOM
CAIE P1," " ;SKIP IF BLANK
DPB P1,[POINT 6,T1,35] ;PUT IN T1, UNASCIIZED THE BYTE
JRST GTWRD1 ;GET NEXT CHAR.
;PREWM - SETS UP THE LOAD ADDR. FOR WORKING MEMORY
; ALSO, SAVES LOC. 0 OF CRAM FOR MICROINSTR. EXECUTION
; T2/ LOAD ADDR.
;
; CALL PREWM
;
; RETURN+1: ALWAYS
PREWM: MOVEM T2,WMADR# ;SAVE LOAD ADDR.
PREWT (DXDR1) ;SELCT PC
TRO T2,IR.EN+PC.EN ;PC=0, SET FLAGS
PUSHJ P,WTRGX ;SET PC
MOVEI T3,DXDR0 ;SELCT IR
PUSHJ P,RDRGX ;READ IR FROM CRAM, PC=0
MOVEM T1,PC0SAV# ;SAVE LOC. 0
;SET MA & MAEX BITS
MOVE T1,WMADR ;GET LOAD ADDR.
ANDI T1,377 ;MAX. ADDR. 256
TRO T1,1000 ;MAKE MICROINTR. (MOVEI LOAD MA)
PUSHJ P,XI ;SET MA REGISTER
MOVE T1,WMADR ;GET LOAD ADDR. AGAIN
LSH T1,-^D8 ;KEEP 2 MAEX BITS
TRO T1,400 ;MAKE MICROINTR. (MOVEI LOAD MAEX)
JRST XI ;SET MAEX BITS AND RETURN
;POSWM - RESTORES LOC. 0 OF CRAM AFTER WORKING WITH WORKING MEMORY
;
; CALL POSWM
;
; RETURN+1: ALWAYS
POSWM: PREWT (DXDR1) ;SELCT PC
TRO T2,PC.EN+MS.EN ;PC=0
PUSHJ P,WTRGX ;SET PC
MOVE T2,PC0SAV ;GET C(LOC 0 OF CRAM)
MOVEI T3,DXDR0 ;SELCT IR
JRST WTRGX ;WRITE CRAM FROM IR
; AND RETURN
;PRECR - SETS UP PC FOR LOADING OR VERIFYING CRAM
; T2/ LOAD ADDR.
;
; CALL PRECR
;
PRECR: ANDI T2,7777 ;MAKE SURE 12 BITS PC
TRO T2,MS.EN+PC.EN+PC.AI ;SET BITS
MOVEI T3,DXDR1 ;SELCT PC
JRST WTRGX ;WRITE PC AND RETURN
;XI - EXECUTE INSTR. IN T1
;
; CALL XI
;
; RETURN+1: ALWAYS
; CHANGES T2,T3,&T4
; PRESERVES T1
XI: PREWT (DXMTR) ;SELCT DXMTR
TRO T2,MP.SC ;CLEAR START BIT & SET SINGLE CYCLE BIT
PUSHJ P,WTRGX ;STOP MICROPROCESSOR
PREWT (DXDR1) ;CLR PC
TRO T2,PC.EN+MS.EN ; AND SET BITS
PUSHJ P,WTRGX ;DO IT
PREWT (DXDR0) ;LOAD IR WITH INSTR.
MOVE T2,T1 ; AND LOAD IT IN LOC. 0, ALSO
PUSHJ P,WTRGX ;
PREWT (DXDR1) ;SELCT PC REG.
TRO T2,IR.EN+PC.AI ;SET IR.EN & PC.AI BIT
PUSHJ P,WTRGX ;PC HAS 0
PREWT (DXMTR) ;READY TO EXECUTE
TRO T2,MP.SC+MP.STA ;SET SINGLE STEP & START BITS
PUSHJ P,WTRGX ;GO START MICROCONTROLLER
PREWT (DXMTR) ;CLEAR START BIT
TRO T2,MP.SC ;LEAVE SINGLE CYCLE BIT ON
JRST WTRGX ;DO IT AND RETURN
SUBTTL MODULE FOR RH20 HANDLING ROUTINES
;DEVXCT - EXECUTES IOT(INPUT/OUTPUT TRANSFER INSTR.) FOUND AT CALL+1
; T3/ DEVICE CODE
;
; CALL DEVXCT
; RETURN+1: ALWAYS
DEVXCT: MOVE T4,@(P) ;FETCH IOT
IOR T4,T3 ;GET DEVICE CODE
XCT T4 ;EXECUTE IT
JRST CPOPJ1 ;RETURN - SKIP OVER IOT INTR.
;WTREG - WRITES INTERNAL OR EXTERNAL REGISTER
; T3/ REGISTER SELECT NUMBER
; T4/ DRIVE NUMBER
; T2/ BIT 18-35 ARE SPECIFIED
;
; CALL WTREG
; RETURN+1:ALWAYS
; DESTROYS T2
WTREG: DPB T3,DO.RS ;SET RS FIELD BIT 0-5 IN T2
TLO T2,(DO.LR) ;SET LR LOAD
JUMPL T2,WTREG1 ;JUMP IF INTERNAL REG.
TLO T2,<(DO.DRE)>(T4) ;SET DRAES BIT & DRIVE NUMBER
;DO.EP BIT 0 ALREADY
WTREG1: XCT RH2DTO ;WRITE IT
PUSH P,T1 ;SAVE T1
XCT RH2CNI ;GET CONI
TRNE T1,CI.RAE ;WAS RAE ERROR?
JRST WTREG2 ;YES, JUMP
POP P,T1 ;RESTORE T1
POPJ P, ;JUST RETURN
WTREG2: MOVE T2,T1 ;READY TO CLEAR RAE
ANDI T2,CO.RAE+CO.ATE+CI.PIA ;SET CONO BITS
XCT RH2CNO ;DO CONO
WARNCR <RAE error on write to RH20>
POP P,T1 ;RESTORE T1
POPJ P, ;RETURN
;WTRGX - SAME AS WTREG, EXCEPT DRVNUM HAS DRIVE NUMBER
WTRGX: MOVE T4,DRVNUM ;GET DRIVE NUMBER
JRST WTREG ;WTREG DOES THE REST OF WORK
;RDREG - READS INTERNAL OR EXTERNAL REGISTER
; T3/ REGISTER NUMBER
; T4/ DRIVE NUMBER
;
; CALL RDREG
;
; RETURN+1: ALWAYS
; T1 GETS VALUE
RDREG: SETZB T2,T1 ;CLEAR THEM
DPB T3,DO.RS ;SET REGISTER SELECT
; DO.LR IS 0 ALREADY
JUMPL T2,RDREG1 ;JUMP ,IF INTERNAL
TLO T2,<(DO.DRE)>(T4) ;SET DRAES BIT & DRIVE NUMBER
;DO.EP BIT 0 ALREADY
RDREG1: XCT RH2DTO ;SET PREPARATION REGISTER
XCT RH2DTI ;READ IN T1
PUSH P,T1 ;SAVE RESULT
XCT RH2CNI ;GET CONI IN T1
TRNE T1,CI.RAE ;WAS RAE ERROR?
JRST RDREG2 ;YES, JUMP
JUMPL T2,RDEXIT ;JUMP,IF INTERNAL REGISTER
POP P,T1 ;GET RESULT
TLNN T1,(DI.CPE) ;CONTROL BUS PAR ERROR?
TLNN T1,(DI.TRA) ;OR NOT TRA(TRA=0)
JUMPN T1,RDREG3 ;ERROR, JUMP IF AN RH20 EXISTS
RDEXIT: ANDI T1,177777 ;CLEAR OUT GARBAGE
POPJ P, ;RETURN
RDREG2: MOVE T2,T1 ;GET CONI BITS IN T2
ANDI T2,CO.RAE+CO.ATE+CI.PIA ;SET CONO BITS
XCT RH2CNO ;DO CONO
TRNN F,DR.CHK ;IS CHECKING FOR DRIVE?
WARNCR <RAE error on read of RH20>
POP P,T1 ;RESTORE RESULT
JRST RDEXIT ;RETURN
RDREG3: PUSH P, T1 ;SAVE RESULT AGAIN
WARNCR < CPE or TRA error on read of RH20>
POP P,T1 ;RESTORE RESULT
JRST RDEXIT ;EXIT
;RDRGX - SAME AS RDREG, EXCEPT DRVNUM HAS DRIVE NUMBER
RDRGX: MOVE T4,DRVNUM ;GET DRIVE NUMBER
JRST RDREG ;RDREG DOES THE WORK
;CHKDRV - CHECK IF SPECIFIED DRIVE ON GIVEN RH20 IS DX20
; T4/ DRIVE NUMBER
;
; CALL CHKDRV
;
; RETURN+1: FAIL RETURN, NOT DX20
; RETURN+2: SUCCESS RETURN
CHKDRV: MOVEI T3,DXDTR ;GET REGISTER NUMBER
TRO F,DR.CHK ;MARK CHECKING FOR DRIVE
PUSHJ P,RDREG ;READ DRIVE TYPE REGISTER
TRZ F,DR.CHK ;RESET THE MARK FLAG
MOVE T2,A.DX20 ;GET TYPE OF DX20
SKIPN T3,A.TYPE ;IF NO /TYPE GIVEN
MOVE T3,TYPTAB(T2) ;USE DEFAULT FOR THIS CONTROLLER TYPE
LDB T2,DT.TYP ;GET TYPE IN T2
CAME T2,T3 ;SKIP IF DX20
POPJ P, ;FAIL, RETURN
JRST CPOPJ1 ;SUCCESS SKIP RETURN
SUBTTL ROUTINES TO PRINT RHNUM AND DRVNUM
;PRHDRV - PRINTS OUT RHNUM FOR RH20, DRVNUM FOR DX20
; CALL PRHDRV
; RETURN+1:ALWAYS
PRHDRV: OUTSTR [ASCIZ/
DX20 Selected: RH20=/]
MOVE T1,RHNUM ;GET C(RHNUM)
PUSHJ P,LOCT ;TYPE IT
OUTSTR [ASCIZ/ DX20=/]
MOVE T1,DRVNUM ;GET C(DRVNUM)
PUSHJ P,LOCT ;TYPE IT
OUTSTR [ASCIZ /
/]
POPJ P,
SUBTTL STORAGE
XLIST ;LITERALS
LIT
LIST
;TABLES INDEXED BY THE TYPE SPECIFIED BY THE /DX20 SWITCH. TX02
;MUST BE THE FIRST ENTRY IN THE TABLE
FILTAB: SIXBIT/DXMCA/ ;DX20/TX02 UCODE IS IN DXMCA.ADX
TX2OFS==.-FILTAB-1
SIXBIT/DXMCD/ ;DX20/RP20 UCODE IS IN DXMCD.ADX
TYPTAB: EXP TY.DX2 ;DX20/TX02 DRIVE TYPE IS 60
EXP TY.RP2 ;DX20/RP20 DRIVE TYPE IS 61
HEDPNT: BLOCK 1 ;POINTER FOR CONSTRUCTING HEADER
HEADER: BLOCK ^D20 ;BLOCK FOR HEADER
HEDEND:
CCINT: EXITX ;^C INTERCEPT BLOCK
1B34
CCINTP: BLOCK 1
BLOCK 1
;DX10 IOT'S
PDCBAS: PHASE 0
PDCCNO:! CONO PDC,(T1)
PDCCNI:! CONI PDC,T1
PDCDTO:! DATAO PDC,T1
PDCDTI:! DATAI PDC,T1
DEPHASE
PDC2BS: CONO PDC2,(T1)
CONI PDC2,T1
DATAO PDC2,T1
DATAI PDC2,T1
;BYTE POINTERS INTO MEM8
MPNTR: POINT 12,MEM8
POINT 12,MEM8,11
POINT 12,MEM8,23
OCHLOC: TTOCH ;PRINT SWITCH
FWAZER:! ;START OF AREA TO CLEAR
A.TYPE: BLOCK 1
PDLST: BLOCK PDSIZ+1
DEV: BLOCK 1 ;DEVICE
NAME: BLOCK 1 ;FILE NAME
EXT: BLOCK 1 ;FILE EXTENSION,,-1 IF . SEEN
DIRECT: BLOCK 1 ;DIRECTORY
DIRPTH: BLOCK 9 ;SFD PATH
INHDR: BLOCK 3 ;INPUT HEADER
OUTHDR: BLOCK 3 ;OUTPUT HEADER
RH2CNI: BLOCK 1 ;STORE IOT'S
RH2CNO: BLOCK 1
RH2DTI: BLOCK 1
RH2DTO: BLOCK 1
XRHNUM: BLOCK 1 ;SAVE THE RH20 NUMBER HAS THE DX20
XRHCNI: BLOCK 1 ;IO INSTR. FOR THE RH20 HAS THE DX20
XRHCNO: BLOCK 1
XRHDTI: BLOCK 1
XRHDTO: BLOCK 1
LINWC: BLOCK 1 ;LOAD ADDR,,WORD COUNT OF DATA LINE
LINDAT: BLOCK ^D32 ;SO MANY DATA WORDS
CHKSUM: BLOCK 1 ;CHECKSUM FOR DATALINE FROM FILE
FILNAM: BLOCK 2
ADDRES: BLOCK 1
VERERR: BLOCK 1 ;FLAG FOR ADDRESS CHECKING
SW8: BLOCK 1 ;PLACE TO REMEMBER PDP-8 CONSOL SWITCHES
BINFLG: BLOCK 1 ;BIN/RIM FLAG
PISAVE: BLOCK 1 ;PLACE TO SAVE DX10 STATUS
APNTR: BLOCK 1 ;POINTER TO MEM8
FEATUR: BLOCK 1 ;FEATURE REGISTER
VERMP: BLOCK 1 ;VERSION # OF MICRO-CODE
EDTMP: BLOCK 1 ;EDIT LEVEL OF MICRO-CODE
FIRZER: BLOCK 1 ;FIRST LOCATION OF ZEROS
LASZER: BLOCK 1 ;LAST ..
A8FLG: BLOCK 1 ;0 := .BIN FILE, -1 := .A8 FILE
MEM8: BLOCK ^D4096/3+1 ;PDP-8 MEMORY
LWAZER==.-1 ;END OF AREA TO CLEAR
FWAONE:! ;START OF AREA TO PRESET TO -1
A.CLR: BLOCK 1 ;/CLEAR:N
A.DUMP: BLOCK 1 ;/DUMP:N
A.END: BLOCK 1 ;/END:N
A.LOAD: BLOCK 1 ;/LOAD:N
A.STRT: BLOCK 1 ;/START:N
A.CHL: BLOCK 1 ;/UNIT:N
A.CPU: BLOCK 1 ;/CPU:N
A.DX10: BLOCK 1 ;/DX10
A.DX20: BLOCK 1 ;/DX20:TYPE
LWAONE==.-1 ;END OF AREA TO PRESET TO -1
END START