Trailing-Edge
-
PDP-10 Archives
-
k20v7d
-
unsupported/rp07.mac
There are no other files named rp07.mac in the archive.
UNIVERSAL DEFS -- RP07 specific macro definitions for RDREG
SUBTTL N. B. Mahoney/NBM
;This file contains the RP07 specific macro definitions for RDREG
;to interpret the RP07 massbus registers. The format of the macros
;is decribed when each macro is defined.
.DIRECTIVE .XTABM,FLBLST,.NOBIN
SALL
;Copyright (C) 1980,1981,1982,1983 by
;Digital Equipment Corporation, Maynard, Mass.
;
;
;This software is furnished under a license and may be used and copied
;only in accordance with the terms of such license and with the
;inclusion of the above copyright notice. This software or any other
;copies thereof may not be provided or otherwise made available to any
;other person. No title to and ownership of the software is hereby
;transferred.
;
;The information in this software is subject to change without notice
;and should not be construed as a commitment by Digital Equipment
;Corporation.
;
;Digital assumes no responsibility for the use or reliability of its
;software on equipment which is not supplied by Digital.
RP7VER==1 ;Major version
RP7MIN==0 ;Minor version
RP7EDT==0 ;Edit number
RP7WHO==0 ;Who edited
SUBTTL Assembly parameters and drive type register definitions
;The following definition controls whether RDREG will ask for the
;DATAO/DATAI drive select field in addition to the RH20 device
;code. For those devices that are always in massbus slot 0 (the
;DX20 for example), set FTDSEL to a 0 and RDREG will always use
;a drive select field of zero. For those devices that do require
;a drive select code, set FTDSEL to -1 and RDREG will ask for and
;use the drive select value specified by the user.
FTDSEL==-1 ;Need drive select for RP07's
;The following macro defines the drive type register values for those
;devices that we can interpret. The arguments to the DTRTYP macro
;are as follows:
;
; 1 - Octal value of drive type (right 9 bits)
; 2 - Corresponding mnemonic for this drive type (this mnemonic
; is used in the second level macro definitions below)
DEFINE DRVTYP,<
DTRTYP 42,RP07 ;;RP07s have a DT of 42
>
SUBTTL First level massbus register definitions
;The following macro defines the registers that we want to read and
;interpret in the device. The arguments to the XX macro are as
;follows:
;
; 1 - Massbus register number (register select field)
; 2 - Mnemonic for the register
;
;Note that the CONI definition MUST be first. RDREG depends on this
;and will work incorrectly if it is not.
DEFINE REGS,<
XLIST
XX 0,CONI ;;CONI - Must be first
XX 0,CR ;;Control register
XX 1,SR ;;Status register
XX 2,ER ;;Error register
XX 3,MR ;;Maintenance register
XX 4,AS ;;Attention summary register
XX 5,DTSA ;;Desired track/Sector address
XX 6,DT ;;Drive type register
XX 7,LAR ;;Look ahead register
XX 11,OFR ;;Offset register
XX 12,DCR ;;Desired cylinder register
XX 13,CCR ;;Current cylinder register
XX 14,ER2 ;;Error register 2
XX 15,ER3 ;;Error register 3
XX 16,EPO ;;ECC position register
XX 17,EPA ;;ECC pattern register
XX 70,SBAR ;;Secondary block address register
XX 71,STCR ;;Secondary transfer control register
XX 72,PBAR ;;Primary block address register
XX 73,PTCR ;;Primary transfer control register
XX 74,IVIR ;;Interrupt vector index register
LIST
>
SUBTTL Second level massbus register definitions
;The following macros define the bits and fields in each of the
;massbus registers that we want to interpret. For each massbus
;register mnemonic that we defined in the first level macro definition
;above, we define a macro with the same name here that gives the
;bit and field definitions for that register. The arguments to
;the FIELDS macro are as follows:
;
; 1 - The bit mask of the bit or field in the 36 bit word
; 2 - The text associated with the bit or field
; 3 - One of BIT, VAL, or NVAL to indicate that this entity is a
; bit, a field containing a positive number, or a field containing
; a negative number, repectively. RDREG only interprets BIT values
; if the bit is on. VAL values are always printed as a field. NVAL
; values are first negated and then always printed as a field.
; 4 - Either ALL or one of the drive type mnemonics defined by
; the DRVTYP macro above. ALL values are interpreted for
; all of the legal drive types. Values that are given with
; a specific drive type mnemonic are only interpreted if the
; device is of that drive type.
DEFINE CR,<
FIELDS 1B35,<Go>,BIT,ALL
FIELDS 37B34,<Fnc>,VAL,ALL
FIELDS 1B24,<DVA>,BIT,ALL
>
DEFINE SR,<
FIELDS 1B20,<Attention>,BIT,ALL
FIELDS 1B21,<Composite error>,BIT,ALL
FIELDS 1B22,<Pos in Progress>,BIT,ALL
FIELDS 1B23,<On-line>,BIT,ALL
FIELDS 1B24,<Write lock>,BIT,ALL
FIELDS 1B25,<Last Sector>,BIT,ALL
FIELDS 1B26,<Programmable>,BIT,ALL
FIELDS 1B27,<Drive present>,BIT,ALL
FIELDS 1B28,<Drive ready>,BIT,ALL
FIELDS 1B29,<Valid Vol>,BIT,ALL
FIELDS 1B33,<Interleaved>,BIT,ALL
FIELDS 1B34,<Early warning>,BIT,ALL
FIELDS 1B35,<Offset mode>,BIT,ALL
>
DEFINE ER,<
FIELDS 1B35,<ILF>,BIT,ALL
FIELDS 1B34,<ILR>,BIT,ALL
FIELDS 1B33,<RMR>,BIT,ALL
FIELDS 1B32,<Par err>,BIT,ALL
FIELDS 1B31,<FMT err>,BIT,ALL
FIELDS 1B30,<Wr clock fail>,BIT,ALL
FIELDS 1B29,<ECC hard err>,BIT,ALL
FIELDS 1B28,<Hdr compare err>,BIT,ALL
FIELDS 1B27,<Hdr CRC err>,BIT,ALL
FIELDS 1B26,<Addr overflow err>,BIT,ALL
FIELDS 1B25,<Invalid addr err>,BIT,ALL
FIELDS 1B24,<Wr lock err>,BIT,ALL
FIELDS 1B23,<Drive Tim err>,BIT,ALL
FIELDS 1B22,<Op Incomp>,BIT,ALL
FIELDS 1B21,<Unsafe>,BIT,ALL
FIELDS 1B20,<Data check>,BIT,ALL
>
DEFINE MR,<
FIELDS 377B35,<Parameter>,VAL,ALL
FIELDS 177B27,<Routine num>,VAL,ALL
FIELDS 1B20,<Diag mode>,BIT,ALL
>
DEFINE AS,<
FIELDS 377B35,<Attentions>,VAL,ALL
>
DEFINE DTSA,<
FIELDS 177B35,<Sector addr>,VAL,ALL
FIELDS 77B27,<Track addr>,VAL,ALL
>
DEFINE DT,<
FIELDS 77B35,<Drive type>,VAL,ALL
FIELDS 1B24,<Drive Request>,BIT,ALL
>
DEFINE LAR,<
FIELDS 177B29,<Sector count>,VAL,ALL
>
DEFINE OFR,<
FIELDS 1B25,<Hdr compare inh>,BIT,ALL
FIELDS 1B24,<ECC inh>,BIT,ALL
FIELDS 1B23,<Format>,BIT,ALL
FIELDS 1B21,<Move trk desc>,BIT,ALL
FIELDS 1B20,<Cmd mod>,BIT,ALL
>
DEFINE DCR,<
FIELDS 1777B35,<Des cyl addr>,VAL,ALL
>
DEFINE CCR,<
FIELDS 1777B35,<Curr cyl addr>,VAL,ALL
>
DEFINE ER2,<
FIELDS 377B35,<Err code>,VAL,ALL
FIELDS 1B27,<Write unsafe>,BIT,ALL
FIELDS 1B26,<Write overrun>,BIT,ALL
FIELDS 1B25,<RW unsafe>,BIT,ALL
FIELDS 1B24,<RW unsafe>,BIT,ALL
FIELDS 1B23,<RW unsafe>,BIT,ALL
FIELDS 1B22,<CROM par>,BIT,ALL
FIELDS 1B20,<Prgrm err>,BIT,ALL
>
DEFINE ER3,<
FIELDS 1B35,<RUN timeout>,BIT,ALL
FIELDS 1B34,<Sync cl fail>,BIT,ALL
FIELDS 1B33,<Sync byte err>,BIT,ALL
FIELDS 1B32,<Data par err>,BIT,ALL
FIELDS 1B31,<SERDES data fail>,BIT,ALL
FIELDS 1B30,<DC unsafe>,BIT,ALL
FIELDS 1B29,<Index unsafe>,BIT,ALL
FIELDS 1B28,<Device check>,BIT,ALL
FIELDS 1B27,<Proc handshk fail>,BIT,ALL
FIELDS 1B26,<Loss cyl err>,BIT,ALL
FIELDS 1B25,<Loss bit err>,BIT,ALL
FIELDS 1B24,<Ctl logic fail>,BIT,ALL
FIELDS 1B23,<Wr curr sense fail>,BIT,ALL
FIELDS 1B22,<Defect skip err>,BIT,ALL
FIELDS 1B21,<Seek incomp>,BIT,ALL
FIELDS 1B20,<Bad sec err>,BIT,ALL
>
DEFINE EPO,<
FIELDS 17777B35,<ECC err addr>,VAL,ALL
>
DEFINE EPA,<
FIELDS 3777B35,<Err burst fld>,VAL,ALL
>
DEFINE SBAR,<
FIELDS 177777B35,<Bl addr or Fr cnt>,VAL,ALL
>
DEFINE STCR,<
FIELDS 1777B29,<Block cnt>,NVAL,ALL
FIELDS 77B35,<Command>,VAL,ALL
>
DEFINE PBAR,<
FIELDS 177777B35,<Bl addr or Fr cnt>,VAL,ALL
>
DEFINE PTCR,<
FIELDS 1777B29,<Block cnt>,NVAL,ALL
FIELDS 77B35,<Command>,VAL,ALL
>
DEFINE IVIR,<
FIELDS 777B35,<Interrupt vector>,VAL,ALL
>
DEFINE CONI,<
FIELDS 1B18,<DB par err>,BIT,ALL
FIELDS 1B19,<Drv exc>,BIT,ALL
FIELDS 1B20,<Long WC>,BIT,ALL
FIELDS 1B21,<Short WC>,BIT,ALL
FIELDS 1B22,<Chan err>,BIT,ALL
FIELDS 1B23,<Drive resp err>,BIT,ALL
FIELDS 1B24,<Reg acc err>,BIT,ALL
FIELDS 1B25,<Chan rdy>,BIT,ALL
FIELDS 1B26,<Overrun>,BIT,ALL
FIELDS 1B27,<MBE>,BIT,ALL
FIELDS 1B28,<Attn>,BIT,ALL
FIELDS 1B29,<STCR full>,BIT,ALL
FIELDS 1B30,<AIE>,BIT,ALL
FIELDS 1B31,<PTCR full>,BIT,ALL
FIELDS 1B32,<Done>,BIT,ALL
FIELDS 7B35,<PI>,VAL,ALL
>
END